12843 Foothill Blvd.,
Suite D
Sylmar, CA 91342
818 898 3380 voice
818 898 3360 fax
Model No. 4000CL-MAV-PBIO
(&4000CL-MAV-T-PBIO)
250 CLIP FAST ACCESS SYSTEM
with Peripheral Bus Interface Option
Sony DP Protocol
for SONY MAV-555 Video Servers
USER MANUAL
1 4000CL-MAV, 250 Clip Fast Access System, for Sony MAV-555, with PBIO option
REFERENCE . . .
15
15.
16.
SETUP MENU
FUNCTION TABLE
15
17
18
18
18
18
18
19
20
17. SPECIFICATIONS
ST300
RS422 SERIAL CONNECTOR
POWER CONNECTOR
AUX CONNECTOR (PBUS IN) RS422 SERIAL CONNECTOR
GPI IN/OUT CONNECTOR
18.
KEY LAYOUT
Manual Version.............................................................3.1 040303
Document No.....…........ 4000CL-MAV-PBIO_User_ Manual.doc
3 4000CL-MAV, 250 Clip Fast Access System, for Sony MAV-555, with PBIO option
1. REVISION HISTORY
120602 Rev. 3.0 Added GPI’s
040303 Rev. 3.1 Added Key Layout
4 4000CL-MAV, 250 Clip Fast Access System, for Sony MAV-555, with PBIO option
Getting Started . . .
2. SYSTEM DESCRIPTION
‰
NOW, production switchers can load & play video clips on Sony MAV DDRs.
‰
Use the EMEM or SNAPSHOT Learn & Recall functions of the production switcher to load
and play a video clip from a Recall or timeline.
‰
Use the Run and Trigger functions of the production switcher to Play, Stop or Recue the video
clip.
‰
‰
Instantly load a video clip at the press of a button.
Instantly load a FILL clip & KEY clip at the press of ONE button, then play out both channels
in sync. LOOP up to 4 channels.
‰
Control up to 4 video channels individually or ganged.
FEATURES
The 4000CL-MAV-PBIO, 400 Clip Instant Access System consists of the ST300-SSM with
Cliplist software.
With this Option, the ST300 has 4 Peripheral Device Addresses, one for each VTR that it controls.
This allows the production switcher to control any and all VTRs connected to the ST300.
Upon receipt of the Learn command from the production switcher, the ST300 saves the CLIP IDs
of the currently loaded clips, the current time of each clip, the VTRs they are loaded on, and the
current GANG mode, into the appropriate Cue Point.
When the Recall command is received, the ST300 loads the “Learned” Clips onto the “Learned”
VTRs, cues the Clip to the “Learned” time, then restores the “Learned” GANG mode.
The Trigger function on the production switcher puts the selected VTRs into Play, Stop, Recue or
other available modes.
DEFINITIONS
‰
‰
‰
Throughout this document, “Video Server” refers to the MAV-555.
The ST300-S/SM as the ST300.
Words surrounded by brackets, for example, [ENTER], are keys on the ST300.
[XXX] + [XXX] means hold the two keys down simultaneously.
‰
“Softkeys” are the row of keys directly below the display that perform multiple functions in
MENU and other modes.
5 4000CL-MAV, 250 Clip Fast Access System, for Sony MAV-555, with PBIO option
3. SYSTEM INSTALLATION
a.
ST300-S/SM, VTR/DDR CONTROLLER
1)
2)
3)
Plug one end of a 9-conductor, RS422 serial cable into the 9-pin connector
(VTR 1, 2, 3 or 4) on the rear of the ST300. Plug the other end of the cable into
the 9-pin REMOTE connector on the Video Server.
Connect the +5, +12, -12 VDC POWER SUPPLY into the POWER connector
on the rear of the ST300. Plug the Power Supply into an outlet, 90 VAC to 240
VAC.
Check SETUP MENU prior to using the ST300 to confirm proper Record mode
and other User settable modes.
b.
PRODUCTION SWITCHER
1)
Connect a standard cable (RS422, 9-pin serial cable) to the “AUX” connector on
the rear of the ST300. Connect the other end of the cable to the Peripheral Bus
Connector on the production switcher. (Communication Format- 38.4K, N, 8,1)
2)
The ST300 has 4 Peripheral Device Addresses, one for each VTR that it
controls. To set the Device Address for each VTR:
a)
Press [MENU] and turn the Wheel until “Peripheral Address” is
displayed.
b)
c)
Press VTR[1], VTR[2], VTR[3] or VTR[4] to select a VTR.
Assign a Peripheral Device Address for that VTR, from 0 to 23,
by entering the desired address using the numeric keypad.
NOTE: Address 24 or greater will turn PBIO off.
d)
Select the next VTR, and then assign a Peripheral Device Address for
it. Each VTR must have its own unique address.
3)
4)
To select a Production Switcher type (Default = Grass Valley Group).
a)
b)
Press [MENU] and turn the Wheel until “SWITCHER” is displayed.
Press the Softkeys to toggle between Sony and Grass Valley.
For version 3.0 hardware, there is an option to set Parity to match the parity of
the production switcher. In hardware versions 2.0 and 2.1, this option is not
offered, as the hardware automatically adjusts for the parity.
5)
6)
When done, press [ESC] to exit the MENU.
Configure the production switcher:
Enable the Peripheral Bus.
Enable the Peripheral Device Addresses assigned to the ST300.
Enable the appropriate Learn/Recall levels.
Enable the Timeline or Recall Trigger function.
6 4000CL-MAV, 250 Clip Fast Access System, for Sony MAV-555, with PBIO option
CONNECTION DIAGRAM
7 4000CL-MAV, 250 Clip Fast Access System, for Sony MAV-555, with PBIO option
4. VIDEO SERVER SETUP
a.
b.
c.
The SONY MAV unit must have the following or higher software versions: V1.1
Clips loaded from the front panel of the MAV will not be displayed on the ST300.
SETUP MENU/RECORD MODE. Crash and Lockout are the only modes supported.
5. LOAD A CLIP
a.
Select VTR. Connection must be to the Player port in order to load existing clips.
b.
Press [CLIP LIST]. The CLIP LIST indicator will turn on. The display prompts:
“WHEEL-scroll files, ENTER-enter file ID”
c.
Turn the Wheel to scroll through the list of available CLIPs.
OR
ENTER a numeric file ID, using the numeric keypad.
d.
e.
Press [LOAD] to load the desired clip.
Repeat steps a - d until clips are loaded into the desired VTRs.
Set the GANG mode, if required. (Refer to the Function Table for Details.)
f.
Press [ESC] at anytime to exit CLIP LIST.
6. LEARN ON THE ST300
a.
LOAD a clip as described above on the ST300.
b.
Select the desired Cue Point by pressing [NEXT CUE], [LAST CUE].
OR
By manually entering the Cue Point using the numeric keypad.
The selected Cue Point number is shown on the bottom line of the display.
c.
Press [SHIFT] + [MARK] to initiate the LEARN.
The ST300 will save loaded CLIP ID and current IN time to the selected Cue Point. The
display shows:
Select VTR:
Mark-Learn, ESC-Cancel
d.
e.
Press VTR[1], VTR[2], VTR[3] or VTR[4] to select the VTRs.
Press [MARK]. The ST300 will: LEARN (save) the current configuration, which
consists of: Cue Point, CLIP IDs, In Times and Ganged VTRs.
8 4000CL-MAV, 250 Clip Fast Access System, for Sony MAV-555, with PBIO option
7. LEARN ON THE PRODUCTION SWITCHER
a.
Select and enable the Peripheral Device Addresses for the ST300.
b.
Do a LEARN to the desired REGISTER. The ST300 will: LEARN (save) the VTR#,
loaded CLIP ID and current IN time to the REGISTER number in the ST300.
8. RECALL ON THE ST300
a.
Select the desired Cue Point by pressing [NEXT CUE], [LAST CUE].
OR
By manually entering the Cue Point using the numeric keypad.
The selected Cue Point number is shown on the bottom line of the display.
b.
Press [LOAD] on the ST300. The ST300 will automatically load the LEARNED clip on
the selected VTR and cue the clip to the LEARNED time.
9. RECALL ON THE PRODUCTION SWITCHER
a.
RECALL the desired REGISTER NUMBER.
b.
The ST300 will automatically load the Learned clips on the Learned VTRs, cue the clips
to the Learned time, then set the Learned GANG mode.
9 4000CL-MAV, 250 Clip Fast Access System, for Sony MAV-555, with PBIO option
10. TRIGGERS FROM THE PRODUCTION SWITCHER
Firing a trigger, using either the Timeline or Run function on the production switcher, causes the
ST300 to put the Video Server into the following modes, based upon the trigger value:
GRASS VALLEY GROUP
Trigger Value
Mode
0
1
2
3
4
5
Play
Recue to beginning of clip
Slo-mo using ST300 Preset Speed
Reverse Play
Still Frame
None
6 or greater
Play
SONY
Trigger Value
Mode
0
1
2
3
4
5
Recue to beginning of clip
Play
Slo-mo using ST300 Preset Speed
Reverse Play
Still Frame
None
6 or greater
Play
To control more than one VTR, enable the Peripheral Device Address for the required VTRs. The
Trigger will be sent to the enabled devices.
OR
GANG the required VTRs on the ST300. See the Menu Table for GANG instructions. Enable the
Peripheral Device Address for one of the GANGed VTRs. The Trigger will be sent to the enabled
VTR. The other VTRs in the GANG will perform the same action.
10 4000CL-MAV, 250 Clip Fast Access System, for Sony MAV-555, with PBIO option
Advanced Features . . .
11. CREATE NEW CLIPS
NOTE: Record duration must be set BEFORE creating a new clip.
a.
Press [SHIFT] + [RECORD].
The first line of the display shows current record duration.
The second line of the display prompts “Enter record length.”
b.
c.
Enter the desired record length using numeric keypad.
Press [ENTER] to save the entered time and exit.
OR
Press [ESC] to exit without saving.
NOTE: Default record duration is 30 minutes.
d.
e.
Select VTR. Connection must be to the Recorder port on MAV-555 to create a clip.
Press [CLIP LIST]. The CLIP LIST indicator will turn on. The display prompts:
The display will show: “Enter New File Name.”
f.
Enter numeric CLIP ID up to 8 characters using the numeric keypad.
g.
Press [LOAD] to create the selected CLIP ID.
OR
Press ESC to exit at anytime.
NOTE: The only functions available for new clips are RECORD and STOP. In order to playback
a newly recorded clip, you must reload it on a Player port.
11 4000CL-MAV, 250 Clip Fast Access System, for Sony MAV-555, with PBIO option
12. TRIMMING A CLIP
a.
SETTING THE IN (OUT) POINT
1)
Press [IN] ([OUT]). The IN (OUT) indicator turns on.
The display shows: “IN (OUT) xx:xx:xx:xx,” where xx:xx:xx:xx is the saved
time.
OR
Press [SHIFT] + [IN] ([OUT]) to manually enter a new IN (OUT) time.
2)
Press [ENTER] to save the entered time.
OR
Press [ESC] to exit without saving.
NOTE: When manually entering IN and OUT points, they are always marked based on
tape time, not LTC, no matter what time mode is selected.
b.
VIEW THE IN (OUT) POINT
1)
When the IN (OUT) indicator is on,
Press [IN] ([OUT]) to view the existing IN (OUT) Point.
2)
While viewing the IN (OUT) Point:
Press [MARK] to overwrite the saved time with the current time.
Press [RECUE] to search to the IN (OUT) point.
c.
CLEARING AN IN (OUT) POINT
Press and hold [DEL] then press and release [IN] ([OUT]).
The IN (OUT) indicator turns off.
d.
TRIM CLIPS
1)
2)
3)
4)
5)
LOAD the clip to be trimmed.
Mark IN and OUT points as described above.
Press [SHIFT] + [TRIM]. The display prompts “Enter new file name.”
Enter new file name (up to 8 characters) using the numeric keypad.
Press [ENTER] or [LOAD] to save the new CLIP ID.
OR
Press [ESC] to exit without saving.
If the saving is successful, the new clip is created. The beginning of the clip is the
marked IN point and the end of the clip is the OUT point. The new clip can be loaded
using the CLIP LIST function. Upon saving the new clip, marked IN and OUT points are
cleared.
NOTE: Do not create trimmed clips with a duration of less than 18 frames.
12 4000CL-MAV, 250 Clip Fast Access System, for Sony MAV-555, with PBIO option
13. VIEW CONTENTS OF CUE POINT
a.
Use [NEXT CUE] or [LAST CUE] to access Cue Point.
Contents loaded at this Cue Point (CLIP ID) will be displayed.
OR
b.
Use numeric keypad to enter Cue Point number.
Press [ENTER].
Contents are displayed.
14. TRANSFERRING CUELIST
a.
TRANSMIT CUE LIST FUNCTION
The TRANSMIT CUELIST function allows you to transmit your list of Cue Points to a
PC, using the provided utility software on the PC, or to another ST300.
1)
TO TRANSMIT CUE POINTS TO THE ST300
a)
Connect the VTR4 connector on the rear of the ST300 to the VTR4
connector of the receiving ST300, using an RS422 9-pin cable with TX
and RX lines crossed.
(A “turnaround” cable)
b)
c)
d)
e)
f)
Press [MENU] and scroll the wheel to “Transmit CUE List?
YES=Enter, Exit=ESC.”
Press [ENTER] to start transmitting. The Display shows “Waiting to
transmit.”
When the Receiver is ready, transfer starts automatically.
The Display now shows “Transmitting cuelist.”
After the transfer is over, the display shows “Transfer is over” for one
second, then shows “Waiting to transmit” again.
Connect another ST300 to transmit the list again.
OR
Press [ESC] twice to exit.
2)
TO TRANSMIT CUE POINTS TO THE PC
a)
b)
Connect the VTR4 connector on the back of the ST300 to one of the
COM ports on the PC using a RS422 to RS232 adapter.
Repeat steps b-f of the TO TRANSMIT CUE POINTS TO THE ST300
section.
13 4000CL-MAV, 250 Clip Fast Access System, for Sony MAV-555, with PBIO option
b.
RECEIVE CUELIST FUNCTION
The RECEIVE CUELIST function allows you to receive your list of Cue Points from a
PC or from another ST300.
1)
TO RECEIVE CUE POINTS FROM THE ST300
a)
Connect the VTR4 connector on the back of the ST300 from the VTR4
connector of the transmitting ST300 using RS422 9-pin cable with TX
and RX lines crossed. (A “Turnaround” Cable)
b)
c)
d)
e)
Press [MENU] and scroll the wheel to “Receive CUE List?
YES=Enter, Exit=ESC.”
Press [ENTER] to start receiving. The Display shows “Waiting to
receive.”
When the Transmitter is ready, transfer starts automatically.
The Display now shows “Receiving cuelist.”
After the transfer is over the display shows “Done-Success! Press any
key…”
f)
Press any key. The display shows “Receive cuelist?” message.
g)
Press [ESC] to exit the MENU mode.
2)
TO RECEIVE CUE POINTS FROM THE PC
a)
b)
Connect the VTR4 connector on the back of the ST300 to one of the
COM ports on the PC using RS422 to RS232 adapter.
Repeat steps b-g of the TO RECEIVE CUE POINTS FROM THE
ST300 section.
14 4000CL-MAV, 250 Clip Fast Access System, for Sony MAV-555, with PBIO option
Reference . . .
15. SETUP MENU
Press [MENU]. The MENU indicator will turn on.
Turn the Wheel to select item to change.
Press [MENU] OR use the Softkeys to change the desired mode for that option.
Turn the Wheel at anytime to select another item.
Press [ESC] at anytime to exit SETUP MENU. The MENU indicator will turn off.
MENU MODES
RECORD
(Turning Wheel Clockwise)
Press [MENU] to select the desired record mode: Lockout, Crash (Full).
WIND MODE
Press Softkey to select:
HOLD (Fast wind is maintained only while key is depressed.)
OR
LATCH (Fast wind is initiated and maintained with momentary key press.)
Select fast wind speed (3.9 to 23.7) by pressing Softkey below SPD.
ST300 display shows:
SLOMO
SLOMO with:
WHEEL
(Non T-Bar version)
SpdRange
Preset
SLOMO with:
TBAR
ST300 display shows:
(T-Bar version)
Wheel
SpdRange
Preset
NOTE - The T-BAR has a fixed speed range of 0 Æ +200 with a detent at
+100 % play speed.
Press Softkey [TBAR] (or [WHEEL]) to toggle between them.
For Wheel only:
Press Softkey [SPDRANGE] to select SLOMO speed ranges.
Press Softkey to select: 0 Æ +200 OR -100 Æ +200.
Press Softkey [BACK] to return to SLOMO MENU.
Press [ESC] to exit OR turn the Wheel to select another item.
For Wheel only:
Press Softkey [PRSET] to select the SLOMO Preset Speed Mode.
Press Softkey [UPDATE]. When exiting SLOMO mode, the last used speed is
saved in the Preset Speed register.
Press Softkey [STATIC]. The Preset Speed register is NOT updated when
exiting SLOMO mode. It is only changed by [SHIFT] + [SLOMO] (PRESET
SLOMO).
15 4000CL-MAV, 250 Clip Fast Access System, for Sony MAV-555, with PBIO option
ST300 SETUP
ST300 SETUP
Clear Cues
SetDefault
Press Softkey beneath ClearCues to clear all Cue Points to 00:00:00:00.
Press Softkey [YES] when asked “Are You Sure?”
Press Softkey beneath SetDefault to set ST300 to default settings.
Press Softkey [YES] when asked “Are You Sure?”
DISPLAY
SOFTWARE
VERSION
The version number for the currently installed software is displayed.
PARITY
In hardware version 3.0 only, set the parity to the same as the switcher.
For hardware versions 2.0 and 2.1, no adjustment is provided or required.
RECORD
Press Softkey to select single button or 2-button record.
RECORD = [REC] Only OR [REC] + [PLAY].
PBIO ADDRESS
Select to match the switcher output. (ALL hardware versions)
SWITCHER TYPE
Select to match the switcher type. (ALL Hardware versions)
TRANSMIT CUELIST Transmit cuelist to another ST300 or to a PC.
RECEIVE CUELIST
Receive cuelist from another ST300 or PC.
16 4000CL-MAV, 250 Clip Fast Access System, for Sony MAV-555, with PBIO option
16. FUNCTION TABLE
Function
Key Press
Description
GOTO ENTERED
TIME
[SHIFT] + [RECUE]
Search the VTR to the manually entered time.
Use the ST300 numeric keypad.
Press [ENTER] or [RECUE].
FFWD
JOG
[FFWD]
Press and HOLD to shuttle. Release key to stop. Set WIND
Speed in MENU.
[JOG]
Select JOG mode and enable Wheel.
Step to the previous Cue Point Location.
Step to the next Cue Point Location.
LAST CUE
NEXT CUE
RECORD
[LAST CUE]
[NEXT CUE]
[REC]
Places VTR into the Record mode selected by RECORD
MODE in the SETUP MENU.
Press [RECORD] or [RECORD] + [PLAY].
REWIND
[RWD]
Press and HOLD to shuttle. Release key to stop. Set WIND
Speed in MENU.
SHUTTLE
SLOMO
[SHUTTLE]
Select SHUTTLE mode and enable Wheel.
[SLOMO]
Press [SLOMO] to slo-mo the VTR. Turn the Wheel (or move
the T-Bar if available) to change the play speed. Press
SLOMO] to STILL frame.
OR
Press any transport key to exit SLOMO.
SLO-MO SPEED
PRESET
[SHIFT] + [SLOMO]
For WHEEL ONLY: Press [SHIFT] + [SLOMO] to preset the
slo-mo speed. Turn the Wheel to select desired speed. Press
[ESC] or any transport key to exit.
STOP
[STOP]
Press once to STILL frame VTR.
Press again to put VTR into STOP mode.
GANG VTRs
[SHIFT] + [VTR #1]
OR
[SHIFT] + [VTR #2]
OR
Press and Hold [SHIFT]. Then when lights go out, press VTR
keys to include in the gang. Press [SHIFT] to escape gang
setup mode. Flashing LED indicates VTR or HDD being
monitored for status.
[SHIFT] + [VTR #3]
OR
[SHIFT] + [VTR #4]
TIME MODE
SELECT
[TIME MODE]
Press to toggle between Timecode (TC), VITC (VT) or Tape
Timer (TM) display modes.
17 4000CL-MAV, 250 Clip Fast Access System, for Sony MAV-555, with PBIO option
17. SPECIFICATIONS
ST300
Power:
Size:
90 VAC to 265 VAC adapter supplied with IEC connector
(L” x W” x H”) 12” x 6” x 1.5” (front) 3.0” (rear)
4 lbs.
Weight:
Rear Panel Connectors: VTR1, VTR2, VTR3, VTR4 … All DB9F
GPI......................................….. DBF15F
Power....................…................ DB9M
Aux .............................…......… DB9F
Display:
Easy to read 2-line, back-lit LCD display
(User adjustable contrast)
Jog/Shuttle Wheel:
Optional “T”-bar:
With mechanical detents
Slo-mo 0-200% of Play Speed
RS422 SERIAL CONNECTOR
9-Pin D-Type, Female
Pin #
1
2
3
4
5
Frame Ground
Receive A Í
Transmit B Î
Transmit Common
Spar
6
7
8
9
Receive Common
Receive B Í
Transmit A Î
Frame Ground
POWER CONNECTOR
9-Pin D-Type, Male
Pin #
1
2
3
4
5
+5v DC
+5v DC
Ground
+12 VDC
–12 VDC
6
7
8
9
+5 VDC
Ground
Ground
Ground
AUX CONNECTOR (PBUS IN) RS422 SERIAL CONNECTOR
9-Pin D-Type, Female (DB9F)
Pin #
1
2
3
4
5
Frame Ground
No Connection
Receive B Í
Common
6
7
8
9
Common
No Connection
Receive A Í
Frame Ground
Spare
18 4000CL-MAV, 250 Clip Fast Access System, for Sony MAV-555, with PBIO option
GPI IN/OUT CONNECTOR
15-Pin D-Type, Female (DB15F)
Pin #
1
2
3
4
5
6
7
8
GPI 1 Out
GPI 2 Out
GPI 3 Out
GPI 4 Out
GPI 5 Out
GPI 6 Out
GPI 7 Out
Ground
Pin#
9
GPI 1 In – Play
GPI 2 In – Stop
GPI 3 In – Recue
GPI 4 In – Next cue
GPI 5 In – Last cue
GPI 6 In – Recall
GPI 7 In
10
11
12
13
14
15
19 4000CL-MAV, 250 Clip Fast Access System, for Sony MAV-555, with PBIO option
18. KEY LAYOUT
20 4000CL-MAV, 250 Clip Fast Access System, for Sony MAV-555, with PBIO option
|