VIDEO
CASSETTE
RECORDER
OWNER’S
MANUAL
SSV6001
TABLE OF CONTENTS
■ IMPORTANT SAFEGUARDS..................................... 2
■ PRECAUTIONS ............................................................ 3
■ FEATURES ................................................................... 4
■ OPERATING CONTROLS AND FUNCTIONS......... 4
■ PREPARATION FOR USE .......................................... 6
■ INITIAL SET UP FOR USE ........................................ 7
■ SET UP FOR USE AGAIN........................................... 8
■ PLAYBACK FUNCTION.............................................. 9
■ RECORDING FUNCTION ........................................ 10
■ TIMER RECORDING................................................. 11
■ SPECIAL FEATURES................................................ 12
■ TROUBLESHOOTING GUIDE................................. 12
■ SPECIFICATIONS ..................................................... 13
■ MAINTENANCE......................................................... 13
■ INSTRUCCIONES EN ESPAÑOL............................ 14
■ WARRANTY ................................................................ 16
SUPPLIED ACCESSORIES
ACCESSORIES
Coaxial Cable
Remote Control Unit
Batteries
PART NO.
WPZ0901LW001
N9374UD or N9377UD
AA x 2
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
As an ENERGY
S
TAR®
Partner, our company has
determined that this product meets
If you need additional operating assistance after reading this
the ENERGY S
TAR® guidelines for
S
TAR® is
owner’s manual or to order replacement accessories, please call
energy efficiency. ENERGY
a U.S. registered mark.
TOLL FREE : 1-800-968-3429.
Please read before using this equipment.
PRECAUTIONS
INSTALL LOCATION
For safety and optimum performance of your VCR:
REMOTE CONTROL
We do not recommend the use of universal remote con-
trols. Not all of the functions may be controlled with a
universal remote control.
If you decide to use a universal remote control with this
unit, please be aware that the code number given may
not operate this unit. In this case, please call the manu-
facturer of the universal remote control.
■
Install the VCR in a horizontal and stable position.
Do not place anything directly on top of the VCR. Do
not place the VCR directly on top of the TV.
■
Shield it from direct sunlight and keep it away from
sources of intense heat. Avoid dusty or humid places.
Avoid places with insufficient ventilation for proper
heat dissipation. Do not block the ventilation holes
on the sides of the VCR. Avoid locations subject to
strong vibration or strong magnetic fields.
FCC WARNING
This equipment may generate or use radio frequency
energy. Changes or modifications to this equipment may
cause harmful interference unless the modifications are
expressly approved in the instruction manual. The user
could lose the authority to operate this equipment if an
unauthorized change or modification is made.
AVOID THE HAZARDS OF ELECTRICAL
SHOCK AND FIRE
■
Do not handle the power cord with wet hands.
■
Do not pull on the power cord when disconnecting it
from AC wall outlet. Grasp it by the plug.
IMPORTANT COPYRIGHT INFORMATION
■
If, by accident, water is spilled on your VCR, unplug
the power cord immediately and take the unit to our
Authorized Service Center for servicing.
Unauthorized recording or use of broadcast television
programming, video tape, film or other copyrighted ma-
terial may violate applicable copyright laws. We as-
sume no responsibility for the unauthorized duplication,
use, or other acts which infringe upon the rights of copy-
right owners.
■
Do not put your fingers or objects into the VCR cas-
sette holder.
MOISTURE CONDENSATION
WARNING
Moisture condensation may occur inside the unit when
it is moved from a cold place to a warm place, or after
heating a cold room or under conditions of high humid-
ity. Do not use the VCR at least for2 hours until itsinside
is dry.
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and
can be reused. Please dispose of any materials in accord-
ance with your local recycling regulations.
Batteries should never be thrown away or incinerated
but disposed of in accordance with your local regula-
tions concerning chemical wastes.
VIDEO CASSETTE TAPE
■
This VCR will operate with any cassette that has the
SERIAL NUMBER
mark. For best results, we recommend the use
of high-quality tapes. Do not use poor quality ordam-
aged tapes.
The serial number of this product may be found on the
back of the VCR. No other VCR has the same serial
number as yours. You should record the number and
other vital information here and retain this book as a
permanent record of your purchase to aid identification
in case of theft. Serial numbers are not kept on file.
■
Avoid moisture. Moisture condensation may occur
on the tape if it is moved from a cold place to a warm
place or visa versa. Before using a tape with these
conditions, to avoid damage of the tape and your
VCR, wait until the tape has warmed to room tem-
perature and the moisture has evaporated.
Avoid extreme heat, high humidity and magnetic
fields.
Date of Purchase
Dealer Purchase from
Dealer Address
Dealer Phone No.
Model No.
■
■
Do not tamper with the cassette mechanism.
■
Do not touch the tape with your fingers.
Serial No.
■
You can prevent accidental erasing
of a recording by breaking off the
tab on the back edge of the cassette.
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLEC-
TRIQUES, INTRODUIRE LA LAME LA PLUS
LARGE DE LA FICHE DANS LA BORNE CORRE-
SPONDANTE DE LA PRISE ET POUSSER
JUSQU’AU FOND.
■
If you decide to record on the tape
Tab
again, cover the hole with plastic
tape.
Download from Www.Somanuals.-co3m-. All Manuals Search And Download.
EN
0J01
FEATURES
Hardware specifications
■ Auto Head Cleaner
■ 4 Head HiFi Stereo
Playback
■ S-VHS Quasi Playback (SQPB)
(Allows you to view a tape recorded in S-VHS format.)
■ Auto Repeat
■ Bilingual on-screen menu display selectable in
English or Spanish
■ 2 Step Picture Search Operation
■ 181 channel capability PLL frequency synthesizer
tuner with direct station call
(A cable converter box may be necessary to view
scrambled cable channels.)
■
Index Search
■ Time Search
Recording
■ 1 Year, 7 events (including Daily and Weekly
Timer Recording)
■ OTR (One Touch Recording)
Automatic functions
■ Auto power on and off system
■ Digital Auto Tracking (DTR)
OPERATING CONTROLS AND FUNCTIONS
VCR FRONT PANEL
REMOTE CONTROL
2
4 5 6
1
3
STOP/EJECT
PLAY
POWER
VCR/TV EJECT
3
REW
F.FWD
7
3
8
1
2
5
8
0
REC/OTR
PAUSE/STILL
CHANNEL
6
VIDEO
L
AUDIO
R
4
7
12
TAPE IN
TIMER
REC
POWER
VCR/TV
MENU
15
9
MENU
+100 SEARCH MODE
8
26 23
7
10
11
12
22
13
14
VCR REAR PANEL9
20
19
18
4
14
16
17
DISPLAY SLOW EXIT COUNTER
21
23 24
MEMORY
PLARYESET
REW
F.FWD
2
3
5
6
ANT
IN
AUDIO
L
STOP
PAUSE/STILL
RECORD
OUT IN
R
13
VIDEO
OUT
CH4
OUT INCH3
25 26 27 28
1. Cassette Compartment
4. PLAY button– Press to begin playback.
2. REW button– Press to rewind the tape, or to view
the picture rapidly in reverse during the playback
mode. (Rewind Search)
Press to enter digits when setting program (For ex-
ample: setting clock or timer program).
Press to select the setting modes from the on screen
menu.
Press to cancel a setting of timer program. Press to
correct digits when setting program (For example: 5. F.FWD button– Press to rapidly advance the tape, or
setting clock or timer program). Press to add or delete
channel numbers during channel preset.
view the picture rapidly in forward during playback.
(Forward Search)
3. EJECT button– Press to remove the tape from the
When setting program (For example: setting clock or
timer program), press to determine your selection
and proceed to the next step you want to input. Press
to determine the setting modes from the on screen
menu. Press to add or delete channel numbers during
channel preset.
VCR.
STOP button– Press to stop the tape motion.
Press to enter digits when setting program (For ex-
ample: setting clock or timer program). Press to se-
lect the setting modes from the on screen menu.
Download from Www.Somanuals.-co4m-. All Manuals Search And Download.
EN
0J01
6. PAUSE/STILL button– Press to temporarily stop 16. DISPLAY button– Press to display the current time,
the tape during recording or to view a still picture
during playback.
Frame Advance function– Press to advance the
picture by one frame at a time during still mode.
channel number, real time tape counter, and other in-
formation on the TV screen. (only on the remote con-
trol)
Each time you press this button, TV screen will
change as shown. The status display (STOP, PLAY
etc.) and the tape speed display (SP, LP (playback
only), or SLP) will disappear after 5 seconds.
7. POWER button– Press to turn VCR on and off.
Press to activate timer recording, when the timer pro-
gram has been set.
8. VCR/TV button– Press to select TV or VCR mode.
<COUNT mode>
<CLOCK mode>
<OFF mode>
STOP
STOP
5:40PM
CH 02
VCR position: to view playback, to monitor video
recordings or watch TV using the VCR tuner.
Press
once
Press
once
SP
0:12:34
SP
TV position: to watch TV or to view one program
while recording another.
Press once
9. Remote sensor window– Receives the infrared
signals from the remote control.
10. Indicators
17. SLOW button– Press to start slow motion playback.
(only on the remote control)
POWER indicator– Indicates that the power is
turned on.
VCR/TV indicator– Indicates that the VCR is in the
VCR position.
TAPE IN indicator– Indicates that there is a tape in
the VCR.
TIMER indicator– Indicates that the timer recording
or OTR has been set.
18. COUNTER MEMORY button– Press to set counter
memory on and off. (only on the remote control)
19. COUNTER RESET button– Press to reset counter
to 0:00:00. (only on the remote control)
EXIT button– Press to exit the menu on the TV
screen. (only on the remote control)
20. SEARCH MODE button– Press to perform a Time
Search or an Index Search. (only on the remote con-
trol)
REC indicator– Indicates that it is recording.
Flashes when a recording has been paused.
21. Power cord– Connect to a standard AC outlet
11. TAPE SPEED button– Press to choose the desired
(120V/60Hz).
recording speed : SP/SLP. (only on the VCR)
22. AUDIO OUT jacks– Connect to the audio input
12. CHANNEL Up or Down buttons– Press to select
jacks of your audio equipment or another VCR.
the desired channels for viewing or recording.
23. AUDIO IN jacks– Connect to the audio output jacks
Tracking function– Press to minimize video ‘noise’
(lines or dots on screen) during playback (only on the
VCR) or slow mode.
Press to stabilize the picture in the Still mode when
the picture begins to vibrate vertically.
of your audio equipment or another VCR.
24. ANT. IN terminal– Connect to an antenna, Cable
system or Satellite system.
25. VIDEO OUT jack– Connect to the video input jack
of your video camera or another VCR.
13. RECORD button– Press for manual recording.
26. VIDEO IN jack– Connect to the video output jack of
OTR button– Press to activate One Touch Record-
ing. (only on the VCR)
your video camera or another VCR.
27. CH3/CH4 selector switch– Use to select a video
14. MENU button– Press to display the menu on the TV
output channel (3 or 4) for VCR playback.
screen. Press to exit the menu on the TV screen.
28. ANT. OUT terminal– Connects to the antenna input
15. NUMBER buttons– Press to select desired channels
for viewing or recording. To select channels from 1
to 9, first press "0" button then 1 to 9. (only on the
remote control)
terminal on your TV.
INSTALLING THE BATTERIES
+100 button– When selecting cable channels which
are higher than 99, press this button first, then press
the last two digits. (To select channel 125, first press
"+100" button then press "2" and "5"). (only on the
remote control)
1) Open the battery compartment cover by pressing the
cover on the remote unit in the direction of the arrow.
2) Insert 2 "AA" penlight batteries into the battery com-
partment in the direction indicated by the polarity
(+/-) markings.
3) Replace the cover.
Install 2 X AA battery
Download from Www.Somanuals.-co5m-. All Manuals Search And Download.
EN
0J01
PREPARATION FOR USE
ANTENNA/CABLE CONNECTIONS
For some of the most common types of connections, please refer to the diagram below. Use only one connection.
For any further complex connections, please contact your local dealer. (You may need additional accessories which
are not supplied).
1 Disconnect the antenna or cable from your TV.
2
Connect the antenna orcable totheANT.IN(Topjack)
of your VCR.
3 Connect one end of the coaxial cable (supplied) to
4
Connect the other end of the coaxial cable (supplied)
to the UHF/VHF antenna jack of your TV.
the ANT.OUT (Bottom jack) of your VCR.
Basic Connections
[Cable Box or Satellite Box]
OUT
IN
From
Cable or
Satellite
Company
ANT
AUDIO
L
OR
IN
IN
OUT
R
Indoor or
VIDEO
OUT
Audio/Video cables
(not supplied)
Outdoor
Coaxial Cable
(Supplied)
CH3 CH4
IN
Antenna
OUT
OR
From
Cable Company
(No Cable Box)
Back of the VCR
IN
R
IN
L
VIDEO
AUDIO
OR
VHF
UHF
VHF
OR
UHF
ANT in
STEREO
TV A/V Terminal
TV Antenna Terminal
USING OPTIONAL AUDIO/VIDEO
OUTPUT JACKS
If your TV has A/V input jacks, you may connect your
VCR’s AUDIO/VIDEO OUTPUT jacks to the
audio/video input jacks on back of your TV.
Direct audio/video connections usually result in a better
picture and sound quality for tape playback. Please see
your TV’s owner’s manual for A/V input connections.
USING AUDIO/VIDEO INPUT JACKS
You can use the A/V input jacks on the front or the back
of the VCR.
1) When you connect the external source to input jacks
on the back of the VCR, select "L1" position for re-
cording by pressing the 0, 0, 1 on the remote control
or CHANNEL Up/Down button.
2) When you connect the external source to input jacks
on the front of the VCR, select "L2" position for re-
cording by pressing the 0, 0, 2 on the remote control
or CHANNEL Up/Down button.
Note: "L1" or "L2" is found before the lowest memo-
rized channel. (Example: CH2)
Note to CATV system installer
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected
to the grounding system of the building, as close to the point of cable entry as practical.
Download from Www.Somanuals.-co6m-. All Manuals Search And Download.
EN
0J01
INITIAL SET UP FOR USE
5
Begin channel preset
SETTING THE CH3/CH4
SWITCH
by pressing the F.FWD button
once. The tuner scans and
memorizes allactivechannels
in your area.
CH 01
If your TV does not have A/V terminals:
AUTO SET UP
When the VCR is in the Playback mode or when the
VCR is in the VCR position, your TV will receive sig-
nals from the VCR on either channel 3 or 4.
■
The VCR distinguishes be-
tween standard TV channels
and cable channels.
To use the VCR with your TV, set the selector switch to
CH3 or CH4 (which is located
6
After scanning, the tuner stops on the lowest
in the back of your VCR),
memorized channel. The TV screen returns to TV
mode.
whichever is not used for nor-
OUT
CH3
CH4
CH3 CH4
mal broadcasts in your area.
Then set your TV to the same
channel.
■
If "AUTO SET UP" appears on the TV screen again,
check the cable connections. Press the F.FWD button
once again and the VCR will begin preset again.
[Back of the VCR]
AUTOMATIC CHANNEL SET UP
You can automatically program the tuner to scan only
the channels you receive in your area.
TO SELECT A DESIRED CHANNEL
You can select the desired channel by using the CHAN-
NELUp or Down button or directly pressing the number
buttons on the remote control.
■
Channel memory programming is NOT needed
Note for using the number buttons:
when you connected the VCR to a cable box or
satellite box as in "Basic connections" on page 6. In
this case, select the VCR and TV to channel 3 or 4
the same channel as the CH3 or CH4 switch on the
back of the VCR. Then, the channel you want to re-
cord or view may be selected at the cable box or sat-
ellite box.
■
When selecting cable channels which are higher than
99, press the +100 button first, then press the last two
digits.
■
You must precede single-digit channel numbers with
a zero (For example: 02, 03, 04 and so on).
■
Follow the steps below once. Repeat it only if there
CLOCK SET UP
Set the clock accurately for proper automatic timer re-
cording. We suggest that you use a TV or radio station
as your time source.
is a power failure orif the VCR is unplugged formore
than 30 seconds. (In these cases, the programmed
channels are erased.)
■
You must follow the steps below before attempting
to play or record a video tape. If you want to play or
record a video tape BEFORE programming the tuner,
you can cancel it by pressing the RESET/EXIT but-
ton. To program the tuner again, see "CHANNEL
SET UP AGAIN" on the next page.
1
Select main menu by pressing the MENU button.
(If the clock is not set, the CLOCK SET menu ap-
pears first. In this case, follow step [3].)
2
Select "CLOCK SET" by pressing the PLAY or
STOP button. Then, press the F.FWD button.
1 You need to connect the antenna or cable to the VCR
first. Then, connect the VCR power plug into a stand-
ard AC outlet.
3
Set the clock.
Set the month
Press the PLAY or STOP button repeatedly.
Then, press the F.FWD button.
Press the PLAY or STOP button repeatedly.
Then, press the F.FWD button.
Press the PLAY or STOP button repeatedly.
Then, press the F.FWD button.
2 Turn on the TV and set the TV to channel 3 or 4.
Now set the CH3/CH4 switch on the back of the VCR
to match the channel selected on the TV.
Set the day
Set the year
3 Turn on the VCR by pressing the POWER button.
Both the POWER indicator and the VCR/TV indica-
tor on the VCR come on.
The day of the week will appear automatically.
Press the PLAY or STOP button repeatedly.
Then, press the F.FWD button.
Set the hour
Press the PLAY or STOP button repeatedly.
Set the minute
Set the AM or PM
4 Select the On Screen Lan-
LANGUAGE SELECT
Then, press the F.FWD button.
————————————————
CLOCK SET
guage ("ENGLISH" or
Press the PLAY or STOP button
repeatedly.
B
ENGLISH
[ON]
"ESPAÑOL") by pressing
the PLAY or STOP button.
Then, press the F.FWD but-
ton.
MONTH DAY
03 19
YEAR
MON 2001
ESPAÑOL
/
HOUR MINUTE
05 40
AM/PM
PM AM
PM
:
■
To go back one step, press the REW button.
Start the clock by pressing the RESET/EXIT or
4
F.FWD button after setting the AM or PM.
Download from Www.Somanuals.-co7m-. All Manuals Search And Download.
EN
0J01
SET UP FOR USE AGAIN
TO ADD/DELETE CHANNELS
CHANNEL SET UP AGAIN
When the VCR automatically programs the tunerto scan
only the channels you receive in your area, some chan-
nels may be skipped due to a weak signal. You can
manually add the channel in the VCR memory. (Of
course, you can later delete the added channel from the
memory again.)
1
Select main menu by press-
- M E N U -
ing the MENU button.
TIMER PROGRAMMING
AUTO REPEAT
CHANNEL SET UP
CLOCK SET
[OFF]
B
LANGUAGE SELECT
AUDIO OUT
TV STEREO
SAP
2
Select "CHANNEL SET UP"
by pressing the PLAY or STOP
button. Then, press the F.FWD
button.
[ON]
1 Select main menu by press-
- M E N U -
ing the MENU button.
TIMER PROGRAMMING
AUTO REPEAT
CHANNEL SET UP
CLOCK SET
[OFF]
3
Select "AUTO SET UP" by
pressing the PLAY or STOP
button. Then, press the F.FWD
button. After scanning, the
tuner stops at the lowest memo-
rized channel.
B
CHANNEL SET UP
——————————————————
2 Select "CHANNEL SET UP"
by pressing the PLAY or STOP
button. Then, press the F.FWD
button.
LANGUAGE SELECT
AUDIO OUT
TV STEREO
[ON]
B
AUTO SET UP
SAP
MANUAL SET UP
■
The VCR distinguishes between standard TV chan-
nels and cable channels.
3 Select "MANUAL SET UP"
by pressing the PLAY or STOP
button. Then, press the F.FWD
button.
CHANNEL SET UP
——————————————————
AUTO SET UP
B
MANUAL SET UP
SELECTING THE ON SCREEN
LANGUAGE
1
Select main menu by press-
- M E N U -
ing the MENU button.
TIMER PROGRAMMING
AUTO REPEAT
CHANNEL SET UP
CLOCK SET
[OFF]
4 Enter the desired channel
number by pressing the
PLAY or STOP button.
B
LANGUAGE SELECT
AUDIO OUT
TV STEREO
SAP
2
Select "LANGUAGE SE-
LECT" by pressing the
PLAY or STOP button. Then,
press the F.FWD button.
MANUAL SET UP
———————————————
[ON]
CHANNEL 30 ( TV )
DELETE
3
Select the On Screen Lan-
guage ("ENGLISH" or
"ESPAÑOL") bypressing the
LANGUAGE SELECT
——————————————
B
ENGLISH
[ON]
5 Add or Delete it from memory by pressing the
F.FWD or REW button so that "ADD" or "DELETE"
flashes on the TV screen accordingly.
ESPAÑOL
PLAY or STOP button.
MANUAL SET UP
———————————————
MANUAL SET UP
———————————————
CHANNEL 30 ( TV )
DELETE
CHANNEL 30 ( TV )
ADD
4
Exit the preset mode by pressing the RESET/EXIT
button.
- DELETED -
- MEMORIZED -
6
Exit the preset mode by pressing the RESET/EXIT
button.
Download from Www.Somanuals.-co8m-. All Manuals Search And Download.
EN
0J01
PLAYBACK FUNCTION
NORMAL PLAYBACK
SEARCH FUNCTIONS
1 Insert the prerecorded tape. The
VCR will turn on. If the safety tab
has been removed, the VCR will
start playback automatically.
PICTURE SEARCH
If you want to skip or repeat a scene while in the play
mode, press the F.FWD or REW button.
■
Press it again and the VCR will now search in super
high speed. (in the LP / SLP modes only)
2 Turn on the TV and set the TV to channel 3 or 4.
Now set the CH3/CH4 switch on the back of the VCR
to match the channel selected on the TV.
TIME SEARCH
You can skip a program for a desired length of time.
3 Begin playback by pressing the PLAY button.
1) Press the SEARCH MODE
■
Tracking adjustment will be set automatically (Digi-
tal Tracking function) when you start playback. To
adjust the tracking manually, press the CHANNEL
Up or Down button on the VCR.
When a tape has reached the end, the VCR will re-
wind the tape to the beginning, eject the tape, and turn
off the VCR automatically.
TIME SEARCH
2 : 5 0
button so that the Time
Search menu appears.
2) Enter your desired time to
skip by pressing the PLAY or
STOP button within 30 sec-
onds.
■
■
3) Press the F.FWD or REW button to start time search.
If you want to go in the forward direction, press the
F.FWD button. If you want to go in the reverse di-
rection, press the REW button.
S-VHS Quasi Playback (SQPB)
This unit allows you to view a tape recorded in S-VHS
format. (Noise lines may appear on the picture.)
4 To stop playback, press the STOP button.
■
After time search, the VCR will play the tape auto-
matically.
STILL/SLOW
1) You can freeze the picture on TV screen by pressing
INDEX SEARCH
The index signal is recorded on the tape automatically
when the recording is started. If you want to view a re-
the PAUSE/STILL button during playback.
■
You can advance the picture by one frame at a time
by pressing the PAUSE/STILL button during the still cording at a specific start point, it can easily be done.
mode.
1) Press the SEARCH MODE
button so that the Index
Search menu appears.
INDEX SEARCH
03
2) You can see the slow motion by pressing the SLOW
button during playback or the still mode.
■
If the noise bar appears on the TV screen, you can re- 2) Enter your desired number by
duce it by pressing the CHANNEL Up or Down button.
pressing the PLAY or STOP
button within 30 seconds.
■
■
After the VCR has been in Still/Slow mode for 5 min-
utes, it will stop automatically to protect the tape and
the video head.
3) Press the F.FWD or REW button to start index
search. If you want to go in the forward direction,
press the F.FWD button. If you want to go in the
reverse direction, press the REW button.
To return playback, press the PLAY button.
■
AUTO REPEAT PLAYBACK
Use this feature allows you to play a tape over and over.
After index search, the VCR will play the tape auto-
matically.
1) Select main menu by pressing the MENU button.
2) Select "AUTO REPEAT" by pressing the PLAY or
STOP button.
3) Begin auto repeat playback by pressing the F.FWD
button so that [ON] will appear next to "AUTO RE-
PEAT" on the TV screen.
■
If the on-screen menu still remains, press the RE-
SET/EXIT button to exit the menu.
■
To cancel the auto repeat mode, press the F.FWD
button at step [3] so that [OFF] appear next to
"AUTO REPEAT" on the TV screen.
When you set the auto repeat mode to [ON] while the
counter memory mode is ON, the VCR will exit the
counter memory mode automatically.
■
Download from Www.Somanuals.-co9m-. All Manuals Search And Download.
EN
0J01
RECORDING FUNCTION
Before recording, make sure:
1] Press the MENU button and select "TV STEREO" or
"SAP" by pressing the PLAY or STOP button. Then,
press the F.FWD button so that [ON] appears next to
your desired item on the TV screen. To exit, press the
RESET/EXIT button.
Although a program may be broadcast in both stereo
and second audio, you must select the recording mode
in TV STEREO or SAP before you record a broadcast.
■
The desired channel is selected by pressing the num-
ber buttons on the remote control or the CHANNEL
Up/Down button. (If you connected the VCR to a
cable box or satellite box as in "Basic connections"
on page 6, select the VCR to channel 3 or 4 the same
channel as the CH3 or CH4 switch on the back of the
VCR. Then, select the channel you want to record at
the cable box or satellite box. In this case, you can
ONLY record and view the SAME channel. )
■
2] Press the MENU button and select "AUDIO OUT"
by pressing the PLAY or STOP button. Then, press
the F.FWD button. Next, select "HIFI" or "MONO"
by pressing the PLAY or STOP button. To exit, press
the RESET/EXIT button.
■
There is a tape with its safety tab into the VCR.
■
The desired recording speed is selected in SP(stand-
ard play) or SLP(super long play) mode by pressing
the TAPE SPEED button on the VCR.
■
While the VCR is set in HIFI stereo mode, HIFI appears on
the TV screen. While the VCR is set in monaural(MONO)
mode, HIFI disappears from the TV screen.
Tape Speed
Recording/Playback Time
Type of tape
T60
T120
T160
SP mode
1 hour
3 hours
2 hours
6 hours
2-2/3 hours
8 hours
MTS RECORDING/MONITOR MODE
SLP mode
Type of
broadcast
Display on STEREO/SAP
Hi-Fi audio track
(2-channel)
Normal audio
track
■
TV STEREO or SAP is selected.
the TV
screen
Selection
L-channel
R-channel
Regular
(monaural
audio)
-None-
-Invalid-
Mono
L
Mono
R
Mono
L+R
VIEWING AND RECORDING
THE SAME PROGRAM
Stereo
broadcast
STEREO
SAP
-Invalid-
1) Begin the recording by pressing the RECORD button.
Bilingual
broadcast
TV STEREO* Main audio
program
Main audio
program
Main audio
program
■
To temporarily stop recording or resume it, press the
SAP*
Sub audio
program
Sub audio
program
Sub audio
program
PAUSE/STILL button. After the VCR has been in
Pause mode for 5 minutes, it will stop automatically
to protect the tape and the video head.
Stereo &
Bilingual
broadcast
STEREO
SAP
TV STEREO*
SAP*
L
R
L+R
Sub audio
program
Sub audio
program
Sub audio
program
2) Stop the recording by pressing the STOP button
when recording is completed.
* You must select the recording mode in TV STEREO or SAP before you record a broadcast.
COPYING A VIDEO TAPE
You can make copies of video tapes made by friends or
relatives for your enjoyment.
Warning:Unauthorized recordings of copyrighted
video tapes may be an infringement of copyright laws.
OTR(One Touch Recording)
This function enables you to set the recording length sim-
ply by pressing the REC/OTR button on the VCR.
1) Begin OTR by pressing the REC/OTR button on the
VCR repeatedly until the desired recording length
appears.
Connect the recording VCR(this unit), the playing VCR(an-
other source) and your TV using the following diagram.
[TV set]
(Use for monitoring)
■
Recording stops when 0:00 is reached.
Audio/Video cables
(not supplied)
[Recording VCR]
(this unit)
Press
Display
Recorded Length
1 press
(normal recording)
ANT
AUDIO
L
IN
Coaxial cable
(supplied)
IN
OUT
OUT
2 presses
3 presses
↓
0:30
1:00
↓
30 minutes
60 minutes
↓
LEFT RIGHT
R
IN
VIDEO
VIDEO
OUT
AUDIO
ANT in
CH3 CH4
IN
OUT
[Playing VCR]
(another source)
17 presses
8:00
480 minutes
1) Insert a pre-recorded tape into the playing VCR.
2) Insert a tape with its safety tab into the recording VCR.
18 presses
(normal recording)
MTS (Multi-Channel Television
Sound) SYSTEM
When you play a VHS tape, or receive a broadcast on
the VCR tuner channel you are watching, the status
shown below will appear when you press the DISPLAY
button on the remote control. When you record the MTS
broadcast signal, you need setting MTS mode.
3) Press the TAPE SPEED button on therecording VCR
to select the desired recording speed (SP/SLP).
4) Select the "L1" or "L2"position on the recording VCR.
See page 6, under "Using audio/video input jacks".
5) Press the REC/OTR button on the recording VCR.
6) Begin playback of the tape in the playing VCR.
■
For best results during dubbing, use the VCR’s front
panel controls whenever possible. The remote con-
STOP
12:00AM
CH 32
STEREO
SAP
trol might affect the playing VCR’s operation.
1]
2]
■
Always use video-quality shielded cables with RCA-
type connectors. Standard audio cables are not rec-
ommended.
SP
0:00:00
HIFI
Download from Www.Somanuals-.c1om0.-All Manuals Search And Download.
EN
0J01
■
You can use a video disc player, satellite receiver, or
other audio/video component with A/V outputs in
place of the playing VCR.
TO MONITOR THE RECORDING
1) Turn on the TV and set the TV to channel 3 or 4. Now
set the CH3/CH4 switch on the back of the VCR to
match the channel selected on the TV.
2) Press the VCR/TV button on the recording VCR so
that the VCR/TV indicator comes on.
TIMER RECORDING
YoumaysettheVCRtostartrecordingwhileyouareaway.
You can set seven programs to record on specific days,
daily or weekly within a 1 year period.
1) Insert a tape with its safety tab into the VCR.
2) Select main menu by pressing the MENU button.
HINTS FOR TIMER
RECORDING
If there is a power failure or the VCR is unplugged
for more than 30 seconds, the clock setting and all
timer settings will be lost.
■
3) Select "TIMER PROGRAMMING" by pressing the
PLAY or STOP button. Then, press the F.FWD button.
■
If the tape runs out before the end time, the VCR will
switch to the Stop mode immediately, eject the tape
and the VCR power will be turned off. The TIMER
indicator will flash.
■
If you have not yet set the clock, "CLOCK SET" ap-
pears. If so, follow the steps [3] and [4] in "CLOCK
SET UP " section. Then, set the timer recording.
■
If a tape is not in the VCR or does not have the safety
tab, the TIMER indicator flashes and timer recording
cannot be performed. Please insert a recordable tape.
4) Set the timer.
Set the program number (1~7)
PROGRAM NUMBER
4
DATE
START TIME
END
CHANNEL
- - / -
- - : - - - -
- - : - - - -
- -
Program number which is not set up flashes.
Press the PLAY or STOP button repeatedly
for the desired program number.
TIME
TO STOP AN AUTOMATIC TIMER
PROGRAM ALREADY STARTED
REC SPEED
- -
Then, press the F.FWD button.
Select once, daily or weekly recording
For once: Press the PLAY or STOP button
to point to "ONCE".
For daily (Monday~Friday):
Press the PLAY or STOP button
to point to "DAILY".
For weekly: Press the PLAY or STOP
button to point to "WEEKLY".
Then, press the F.FWD button.
Press the STOP/EJECT button on the VCR.
TO CHECK, CORRECT, OR CANCEL AN
AUTOMATIC TIMER PROGRAM
1) Turn the power on.
2) Select main menu by pressing the MENU button.
3) Select "TIMER PROGRAMMING" by pressing the
PLAY or STOP button. Then, press the F.FWD button.
4) Select the program number which you want to check
by pressing the PLAY or STOP button. The details
of the selected program appears on the TV screen.
PROGRAM NUMBER
4
ONCE
DAILY
WEEKLY
Set the date
First, press the PLAY or STOP button for the month,
then, press the F.FWD button.
Next, press the PLAY or STOP button for the day.
Then, press the F.FWD button.
Set the start time
First, press the PLAY or STOP button for the hour,
then, press the F.FWD button.
Next, press the PLAY or STOP button for the minute,
then, press the F.FWD button.
And then, press the PLAY or STOP button for AM or PM.
Then, press the F.FWD button.
Set the end time
Follow the instructions of "Set the start time"
to set the end time.
■
Go to the digit you want to change by pressing the
F.FWD or REW button. Then, enter correct num-
bers by pressing the PLAY or STOP button.
■
You may cancel the entire program by pressing the
REW button during the program number flashes.
5) Press the RESET/EXIT button to exit.
6) Press the POWER button to return to timer stand-
by mode.
Set the channel number
Press the PLAY or STOP button repeatedly
AVOIDING OVERLAPPING PROGRAMS
There may be times when a program will not record.
When programs overlap:
for the desired channel number.
Then, press the F.FWD button.
If you connected the VCR to a cable box or satellite box as in
"Basic connections" on page 6, select the VCR to channel 3
or 4 the same channel as the CH3 or CH4 switch on the back
of the VCR. Then, select the channel you want to record at
the cable box or satellite box. Leave the cable box or satellite
■
The program with the earliest start time has priority.
■
Once the earliest program finishes, the overlapping
program with the lower number will begin recording
in sequence.
box on for timer recording.
ONE TIME PROGRAM
PROGRAM NUMBER
4
Set the tape speed
Press the PLAY or STOP button repeatedly
for the desired tape speed.
DATE
START TIME
END
CHANNEL
05/03 THU
07:30 PM
08:30 PM
16
TIME
■
The illustration below demonstrates the sequence of
recordings.
REC SPEED
SP
SP
SLP
Then, press the F.FWD button.
Recording Sequence
■
To go back one step, press the REW button.
Program 1
5) To set another program, repeat step [4]. To exit, press
the RESET/EXIT button.
6) Press the POWER button to set the timer. The TIMER
indicator on the VCR comes on.
(10:00AM-11:00AM)
Program 2
(9:00AM-10:00AM)
Program 3
(9:30AM-12:00PM)
9:00AM
10:00AM
11:00AM
12:00PM
*Recording period is SHADED
Download from Www.Somanuals-.c1om1.-All Manuals Search And Download.
EN
0J01
SPECIAL FEATURES
COUNTER MEMORY FUNCTION
Use this feature to memorize the beginning of recording
start point.
AUTO REWIND
When a tape has reached the end during recording, play-
back, or fast-forward, the tape will automatically rewind
to the beginning. After rewinding finishes, the VCR will
eject the tape and turn itself to off.
1) Press the COUNTER RE-
REC
SET button on the remote
control to reset the counter.
■
The tape will not auto-rewind during timer recording
or One Touch Recording.
When the Counter Memory is activated, the tape will
rewind to the M0:00:00 and the VCR will go into the
Stop mode.
2) Press the COUNTER
MEMORY button on the
■
SP
M
0:00:00
remote control so that "M"
appears on the TV screen.
3) Record the program.
REAL TIME TAPE COUNTER
This shows the elapsed recording or playback time in
hours, minutes, and seconds. (The displayed time
will not change during blank portions on the tape.)
The "–" indication will appear when the tape is re-
wound further than "0:00:00" on the tape counter.
4) After recording, press the STOP button then the
REW button.
■
■
When "0:00:00" is reached, rewinding operation
goes to stop. And you can view the recording pro-
gram.
■
■
The COUNTER MEMORY button does not function
if the auto repeat mode is set to [ON]. In this case, set
the auto repeat mode to [OFF].
■
To cancel the counter memory mode, press the
COUNTER MEMORY button so that "M" disap-
pears from the TV screen.
TROUBLESHOOTING GUIDE
If you have followed the instructions contained in this manual and have difficulty in operating your VCR, locate
the PROBLEM in the left column below. Check the corresponding CORRECTIVE ACTION column to remedy
the problem.
PROBLEM
CORRECTIVE ACTION
Make sure the power plug is connected to an AC outlet.
Make sure the power is turned on.
Make sure the timer recording is set correctly.
Make sure the power is off.
Make sure the VCR clock is set correctly.
Make sure the tape has a safety tab. If needed, cover the hole with
plastic tape.
■
■
■
■
■
■
No power.
Timer recording is not possible.
Cannot go into Record mode.
■
■
Playback picture is partially noisy.
Adjust tracking control for a better picture by pressing the
CHANNEL Up or Down button on the VCR.
Head cleaning may be necessary. Refer to "AUTO HEAD
CLEANING" .
Cannot view a tape but the audio is
OK.
■
■
Make sure the VCR is not in the Menu mode.
Set your TV to the VCR mode and/or press the VCR/TV button so that
the VCR/TV indicator on the VCR comes on.
No picture or poor picture on
playback.
■
■
■
Fine tune your TV.
Re-check the ANT. IN and ANT. OUT connections. See page 6.
Set your TV to the TV mode and/or press the VCR/TV button so that
the VCR/TV indicator on the VCR disappears.
On-the-air TV programs cannot be
seen.
■
■
■
No VCR operation from the infrared
Remote Control.
Make sure the power plug is connected to an AC outlet.
Check batteries in remote control.
You cannot copy a copyrighted video tape. You are experiencing
copy guard protection.
Video or color fades in and out when
making a copy of a video tape.
Download from Www.Somanuals-.c1om2.-All Manuals Search And Download.
EN
0J01
SPECIFICATIONS
Television system :
Video heads :
Tape cassette :
Tape speed
Recording :
Playback :
Tuner channel
NTSC, TV standard
Rotary four-head
Video output level :
Video output impedance : 75Ω
1Vp-p
Audio output level :
Video input level :
Audio input level :
Power requirement :
Power consumption :
Dimensions :
-6dBv (1KHz)
0.5~2.0Vp-p
-10dBv
120V, 60Hz
14 Watts
video cassette
SP, SLP
SP, LP, SLP
W
H
14-1/4" (360mm)
3-5/8" (92mm)
VHF :
UHF :
#2~#13
#14~#69
D
8-1/2" (215.5mm)
Cable channel :
RF converter :
Converter output :
Timer indication :
Operating temperature : 5 C~40 C (41 F~104 F)
Terminals
5A, A-5 ~ A-1, A ~ W+84
Built-in VHF converter
VHF Channel 3 or 4.
AM/PM 12-hour system
Weight :
5.3 lbs. (2.4 Kg.) (approx.)
■
Designs and specifications are subject to change
without notice and without legal obligation.
o
o
o
o
■
If there is a discrepancy between languages, the de-
fault language will be English.
Antenna input :
Antenna output :
Video input/output :
F type connector x 1
F type connector x 1
RCA connector x 3
Audio input/output : RCA connector x 6
MAINTENANCE
SERVICING
AUTO HEAD CLEANING
■
Should your VCR become inoperative, do not try to cor-
rect the problem by yourself. There are no user-service-
able parts inside. Turn off, unplug the power plug, and
please call our help line at 1-800-968-3429, to locate an
Authorized Service Center.
Automatically cleans video heads as you insert or re-
move a cassette, so you can see a clear picture.
■
Playback picture may become blurred or interrupted
while the TV program reception is clear. Dirt accu-
mulated on the video heads after long periods of use,
or the usage of rental or worn tapes can cause this
problem.
CABINET CLEANING
If a streaky or snowy picture appears during play-
back, the video heads in your VCR may need to be
cleaned.
■
Wipe the front panel and other exterior surfaces of
the VCR with a soft cloth immersed in lukewarm
water and wrung dry.
1. Please visit your local Audio/Video store and pur-
chase a good quality VHS Video Head Cleaner.
2. If a Video Head Cleaner does not solve the problem,
please call our help line at 1-800-968-3429, to locate
an Authorized Service Center.
■
Never use a solvent or alcohol. Do not spray insecti-
cide liquid near the VCR. Such chemicals may cause
damage and discoloration to the exposed surfaces.
NOTES:
■
Remember to read the instructions included with the
video head cleaner before use.
■
Clean video heads only when problems occur.
Download from Www.Somanuals-.c1om3.-All Manuals Search And Download.
EN
0J01
CONEXIONES DE ANTENA/TELEVISIÓN POR CABLE
Para conocer algunos de los tipos de conexión más comunes, consulte 3. Conecte un extremo del cable coaxial (suministrado) a ANT.OUT
las explicaciones siguientes. Utilice solamente una conexión. Para ha-
cer conexiones más complejas, consulte a su concesionario local. (Tal
vez necesite accesorios adicionales que no han sido incluidos.)
(toma inferior) de su videograbadora.
4. Conecte el otro extremo del cable coaxial (suministrado) a la toma
de antena UHF/VHF de su televisor.
NOTA: Para obtener más información, consulte la sección "Conexio- 5. Si su televisor no tiene terminales A/V: Ponga el conmutador se-
nes de antena/televisión por cable" en la página 6.
lector en CH3 o CH4 (en la parte trasera de su videograbadora), el
que no se utilice para las
1. Desconecte la antena o la caja de televisión por cable de su tele-
visor.
2. Conecte la antena o la caja de televisión por cable a ANT.IN (toma
superior) de su videograbadora.
emisiones normales en su
zona. Luego ajuste el televi-
OUT
CH3
CH4
CH3 CH4
sor al mismo canal.
[Parte trasera de la videograbadora]
[Caja de televisión por cable o caja de emisiones de satélite]
Conexiones básicas
OUT
IN
De empresa
de televisión
por cable o
ANT
AUDIO
L
de emisiones
O
IN
de satélite
IN
OUT
R
Antena
interior o
exterior
VIDEO
OUT
Cables de audio/vídeo
(no suministrado)
Cable coaxial
(suministrado)
CH3 CH4
IN
OUT
O
De empresa
de televisión
por cable
Parte trasera de
la videograbadora
(Ninguna caja
de televisión
por cable)
IN
R
IN
L
AUDIO
VIDEO
O
VHF
UHF
VHF
UHF
O
ANT in
EQUIPO ESTÉREO
Terminal TV A/V
Terminal de antena del televisor
PREPARACIÓN DE CANALES
(La antena o la caja de televisión por
cable deberá estar conectada)
PREPARACIÓN DEL RELOJ
1. Pulse el botón MENU hasta que aparezca el menú principal.
(Si el reloj no está puesto en hora y se pulsa el botón MENU, el
menú AJUSTE DE RELOJ aparece en primer lugar. En este caso,
siga el paso 3.)
2. Pulse el botón PLAY o STOP para indicar a "AJUSTE DE RE-
LOJ". Luego, pulse el botón F.FWD.
NOTA: Cuando utilice su nueva videograbadora por primera vez, o
en el caso de ser necesario después de producirse un fallo en la ali-
mentación, la videograbadora se pondrá inicialmente en el modo de
preajuste cuando se pulse el botón POWER.
Si conecta una caja de televisión por cable o una caja de emisiones vía
satélite, consulte la sección "Preparación automática de canales" del
manual del propietario.
1. Encienda el televisor y ponga el televisor en el canal 3 ó 4. Ahora
ponga el conmutador de la parte trasera de la videograbadora para
que concuerde con el canal seleccionado en el televisor.
3.
Ajuste el mes.
Ajuste el día.
Ajuste el año.
Ajuste la ora.
Ajuste el minuto.
Pulse repetidamente el botón PLAY o STOP.
Luego, pulse el botón F.FWD.
Pulse repetidamente el botón PLAY o STOP.
Luego, pulse el botón F.FWD.
Pulse repetidamente el botón PLAY o STOP.
Luego, pulse el botón F.FWD.
2. Pulse el botón POWER para encender la video-
SELEC. IDIOMA
Pulse repetidamente el botón PLAY o STOP.
Luego, pulse el botón F.FWD.
——————————————
grabadora.
ENGLISH
3. Seleccione "ENGLISH" o "ESPAÑOL" (Spa-
B ESPAÑOL [ON]
Pulse repetidamente el botón PLAY o STOP.
Luego, pulse el botón F.FWD.
nish) pulsando el botón PLAY o STOP. Y luego
pulse el botón F.FWD.
AJUSTE DE RELOJ
Pulse repetidamente
el botón PLAY o STOP.
4. Pulse una vez el botón F.FWD.
Ajuste la
mañana (AM) o
la tarde (PM).
MES
0 3
DIA
1 9
AÑO
LUN 2001
El sintonizador explora y memoriza todos los canales activos de
su zona. Tras la exploración, el sintonizador se detiene en el canal
memorizado más bajo.
/
HORA MINUTO
05 40
AM/PM
PM AM
PM
:
●
Para volver atrás un paso, pulse el botón REW.
4. Después de establecer AM o PM, pulse el botón RESET/EXIT o
F.FWD para poner en funcionamiento el reloj.
Download from Www.Somanuals-.c1om4.-All Manuals Search And Download.
ES
0J01
CONTROLES DE FUNCIONAMIENTO Y FUNCIONES
2
4
5
6
1
3
PANEL DELANTERO
MANDO A DISTANCIA
STOP/EJECT
PLAY
DE LA VIDEOGRABADORA
REW
F.FWD
POWER
VCR/TV EJECT
3
7
3
8
12
REC/OTR
PAUSE/STILL
1
2
5
8
0
VIDEO
L
AUDIO
R
TAPE IN
TIMER
REC
POWER
VCR/TV
MENU
CHANNEL
6
4
7
15
9
8
26 23
21
7
9
10
11
12
22
13
14
MENU
+100 SEARCH MODE
20
19
18
4
14
16
17
PANEL TRASERO DE LA
VIDEOGRABADORA
DISPLAY SLOW EXIT COUNTER
23 24
MEMORY
PLARYESET
REW
F.FWD
AUDIO
L
ANT
IN
2
3
5
6
OUT IN
R
STOP
PAUSE/STILL
RECORD
VIDEO
OUT
13
OUT INCH3
CH4
25 26 27 28
1. Compartimiento del videocasete
12. Botones de selección de canales (CHANNEL) - Púlselos para se-
leccionar los canales deseados para ver o grabar.
2. Botón de rebobinado (REW) - Púlselo para rebobinar la cinta o para
ver rápidamente la imagen en retroceso durante el modo de reproducción.
(Búsqueda con rebobinado)
Púlselo para cancelar un ajuste de programa de temporizador. Púlselo para
corregir los dígitos al programar (por ejemplo: puesta en hora del reloj o un
programa de temporizador). Púlselo para añadir o borrar números de canales
durante el preajuste de canales.
Función de seguimiento – Pulse los botones para minimizar el "ruido"
de vídeo (líneas o puntos en la pantalla) durante la reproducción (sólo en la
videograbadora) o el modo de cámara lenta.
Púlselo para estabilizar la imagen en el modo de imagen fija cuando ésta
empieza a vibrar verticalmente.
13. Botón de grabación (RECORD) - Púlselo para realizar la grabación
manual.
3. Botón de expulsión (EJECT) - Púlselo para sacar el videocasete de la
videograbadora.
Botón de grabación con un toque (OTR) - Púlselo para activar la
grabación con un toque. (Sólo en la videograbadora)
14. Botón de menús (MENU) - Púlselo para visualizar los menús en la pan-
talla del televisor. Y vuelva a pulsarlo para salir de los menús de la pantalla
del televisor.
Botón de parada (STOP) - Púlselo para detener la cinta.
Púlselo para introducir los dígitos cuando establezca programas (por ejem-
plo: puesta en hora del reloj o un programa de temporizador). Púlselo para
seleccionar los modos de ajuste en el menú en pantalla.
4. Botón de reproducción (PLAY) - Púlselo para iniciar la reproducción.
Púlselo para introducir los dígitos cuando establezca programas (por ejem-
plo: puesta en hora del reloj o un programa de temporizador).
Púlselo para seleccionar los modos de ajuste en el menú en pantalla.
5. Botón de avance rápido (F.FWD) - Púlselo para avanzar rápidamente
la cinta o para ver rápidamente la imagen en avance durante la reproducción.
(Búsqueda en avance)
15. Botones de números (NUMBER) - Púlselos para seleccionar los cana-
les deseados para ver o grabar. Para seleccionar los canales del 1 al 9, pulse
primero el botón "0" y luego el botón 1 a 9. (Sólo en el mando a distancia)
Botón +100 - Cuando seleccione canales de televisión por cable cuyo nú-
mero sea superior al 99, pulse primero este botón, y luego pulse los dos
últimos dígitos. (Para seleccionar el canal 125, pulse primero el botón
"+100" y luego el "2" y el "5".) (Sólo en el mando a distancia)
Cuando establezca un programa (por ejemplo: puesta en hora del reloj o un
programade temporizador), púlselo para determinar su selección yproseguir
con el siguiente paso que desee introducir. Púlselo para determinar los mo-
dos de ajuste del menú en pantalla. Púlselo para añadir o borrar números de
canales durante el preajuste de canales.
6. Botón de pausa/imagen fija (PAUSE/STILL) - Púlselo para detener
temporalmente la cinta durante la grabación o para ver una imagen fija du-
rante la reproducción.
16. Botón del visualizador (DISPLAY) - Púlselo para visualizar en la pan-
talla del televisor la hora actual, el número del canal, el contador de cinta en
tiempo real y otra información. (Sólo en el mando a distancia)
Cada vez que pulse este botón, la pantalla del televisor cambiará. La visua-
lización del estado (PARAR, REPRODUCIR, etc.) y la visualización de
velocidad de la cinta [SP, LP (reproducción solamente) o SLP] desaparecerá
después de 5 segundos.
17. Botón de cámara lenta (SLOW) - Púlselo para iniciar la reproducción
de cámara lenta. (Sólo en el mando a distancia)
18. Botón de memoria del contador (COUNTER MEMORY) - P ú l s e l o
para activar y desactivar lamemoriadelcontador. (Sólo en el mando adistancia)
19. Botón de reposición del contador (COUNTER RESET) - Púlselo
para reponer el contador a 0:00:00. (Sólo en el mando a distancia)
Función de avance de cuadro - Púlselo paraavanzar laimagencuadro
a cuadro durante el modo de imagen fija.
7. Botón de la alimentación (POWER) - Púlselo para encender y apagar
la videograbadora. Púlselo para activar la grabación con temporizador cuan-
do ésta haya sido establecida.
8. Botón de videograbadora/televisor (VCR/TV) - Púlselo para selec-
cionar el modo de la videograbadora (VCR) o del televisor (TV).
PosiciónVCR:para ver la reproducción, comprobarlasgrabacionesdevídeo
o ver programas de TV utilizando el sintonizador de la videograbadora.
Posición TV: para ver programas de TV o para ver un programa mientras se
graba otro.
9. Ventanilla sensora del mando a distancia - Recibe las señales in-
frarrojas procedentes del mando a distancia.
10. Indicadores
Botón de salida (EXIT) - Púlselo para salir de los menús en pantalla.
(Sólo en el mando a distancia)
20. Botón del modo de búsqueda (SEARCH MODE) - Púlselo para re-
alizar una búsqueda con tiempo o una búsqueda con índice. (Sólo en el
mando a distancia)
21. Cable de alimentación - Conéctelo a una toma de CA estándar (120
V/60 Hz).
22. Tomas de salida de audio (AUDIO OUT) - Conéctelas a las tomas de
entrada de audio de su equipo de audio o de otra videograbadora.
23. Tomas de entrada de audio (AUDIO IN) - Conéctelas a las tomas de
salida de audio de su equipo de audio o de otra videograbadora.
24. Terminal de entrada de antena (ANT. IN) - Aquí se conecta una ante-
na, sistema de televisión por cable o sistema de emisiones vía satélite.
25. Toma de salida de vídeo (VIDEO OUT) - Conéctela a la toma de en-
trada de vídeo de su videocámara o de otra videograbadora.
26. Toma de entrada de vídeo (VIDEO IN) - Conéctela a la toma de salida
de vídeo de su videocámara o de otra videograbadora.
Indicador de alimentación (POWER) - Indica que la alimentación
está conectada.
Indicador de videograbadora/televisor (VCR/TV) - Indica quelavi-
deograbadora está activada.
Indicador de videocasete introducido (TAPE IN) - Indica que hay
un videocasete en la videograbadora.
Indicador del temporizador (TIMER) - Indica que ha sido establecida
la grabación con temporizador u OTR.
27. Conmutador selector de canales CH3/CH4 - Se utiliza para seleccio-
naruncanaldesalidadevídeo(3 ó4)paralareproduccióndelavideograbadora.
28. Terminal de salida de antena (ANT. OUT) - Conéctelo al terminal de
entrada de la antena de su televisor.
Indicador de grabación (REC) - Indica que la videograbadora está gra-
bando. Parpadea cuando la grabación ha hecho una pausa.
11. Botón de velocidad de cinta (TAPE SPEED) - Púlselo para elegir la
velocidad de grabación deseada: SP/SLP. (Sólo en la videograbadora)
Download from Www.Somanuals-.c1om5.-All Manuals Search And Download.
ES
0J01
LIMITED WARRANTY
Funai Corporation will exchange or repair this product, at its option, in the event of defect in materials or workmanship as follows:
EXCHANGE DURATION:
1-90 DAYS:
FUNAI CORPORATION will exchange for a new unit without change for a period of ninety (90)
days from the date of original retail purchase.
91-365 DAYS: FUNAI CORPORATION will exchange for a factory-service-to-new-condition unit for a charge of
$49.00 for the period of ninety one (91) days to three hundred sixty five (365) days from the date of
original retail purchase.
REPAIR DURATION:
LABOR:
FUNAI CORPORATION will provide the labor without charge for a period of ninety (90) days from
the date of original retail purchase.
PARTS:
FUNAI CORPORATION will provide parts to replace defective parts without charge for a period of
one (1) year from the date of original retail purchase. Two (2) years for Picture Tube. Certain parts
are excluded from this warranty.
LIMITS AND EXCLUSIONS:
This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail purchase will be
required together with the product to obtain exchange or service under this warranty.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced or missing. This SYLVANIA
Limited warranty applies only to product purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship, which occur during normal use. It does not cover damage
which occurs in shipment, or failures which are caused by repairs, alterations, or parts not supplied by FUNAI CORPORATION, or
damage which results from accident, misuse, abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance,
commercial use such as hotel, rental or office use of this product, or damage which results from fire, flood, lightning or other acts of
God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE CONTROL
UNITS), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMONSTRATION OR FLOOR MODELS.
FUNAI CORPORATION AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE
INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES INCLUDING
THE WARRANTY OF MERCHANT ABILITY, AND FITNESS FOR A PARTICULAR PURPOSE, THAT ARE HEREBY
DISCLAIMED BY FUNAI CORPORATION AND ITS REPRESENTATIVES OR AGENTS IN THE UNITED STATES.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED CENTER. THIS
WARRANTY IS VALID WHEN THE PRODUCT IS DELIVERED PREPAID TO A FUNAI AUTHORIZED SERVICE FACILITY.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS THAT VARY
FROM STATE TO STATE, IF AT ANY TIME DURING THE WARRANTY PERIOD YOU ARE UNABLE TO OBTAIN
SATISFACTION WITH THE EXCHANGE OR REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORPORATION.
ATTENTION:
FUNAI CORPORATION RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT
WITHOUT PRIOR NOTICE.
For information about your product, or for information on how to exchange or repair your product,
telephone or write to the following:
FUNAI CORPORATION
Customer Service
100 North Street; Teterboro, NJ 07608
Telephone (800)968-3429
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
Printed in China
0VMN02761
H7905UD ★★★★★
|