Sylvania DVD Player CDVC800D User Manual

OWNER’S

MANUAL

DVD PLAYER with VIDEO CASSETTE RECORDER

CDVC800D

ReWritable

Recordable

POWER

OPEN/CLOSE

CHANNEL

STOP/EJECT

PLAY

DVD

VCR

VIDEO

AUDIO

OUTPUT

DVD

VCR TIMER REC REC

STOP

PLAY

REW

F.FWD

If you need additional assistance for set-up or operating

after reading owner’s manual, please call

TOLL FREE : 1 800 287-4871.

Please read before using this equipment.

IMPORTANT SAFEGUARDS

1. Read Instructions - All the safety and operating instruc-

ing of the mast and supporting structure, grounding of the

lead-in wire to an antenna discharge unit, size of grounding

conductors, location of antenna-discharge unit, connection

to grounding electrodes, and requirements for the grounding

electrode. (Fig. A)

tions should be read before the appliance is operated.

2. Retain Instructions- The safety and operating instructions

should be retained for future reference.

3. Heed Warnings - All warnings on the appliance and in the

operating instructions should be adhered to.

4. Follow Instructions - All operating and use instructions

should be followed.

FIGURE A

ANTENNA

LEAD

EXAMPLE OF ANTENNA GROUNDING

WIRE

AS PER NATIONAL ELECTRICAL CODE

GROUND

CLAMP

5. Cleaning - Unplug this video product from the wall outlet

before cleaning. Do not use liquid cleaners or aerosol clean-

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

ers.

Use

damp

cloth

for

cleaning.

EXCEPTION: A product that is meant for uninterrupted ser-

vice and, that for some specific reason, such as the possibil-

ity of the loss of an authorization code for a CATV convert-

er, is not intended to be unplugged by the user for cleaning

or any other purpose, may exclude the reference to unplug-

ging the appliance in the cleaning description otherwise

required in item 5.

6. Attachments - Do not use attachments not recommended by

the video product manufacturer as they may cause hazards.

7. Water and Moisture - Do not use this video product near

water, for example, near a bath tub, wash bowl, kitchen sink,

or laundry tub, in a wet basement, or near a swimming pool,

and the like.

ELECTRIC

SERVICE

EQUIPMENT

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMP

NEC – NATIONAL ELECTRICAL CODE

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

S2898A

14. Lightning - For added protection for this video product dur-

ing a lightning storm, or when it is left unattended and

unused for long periods of time, unplug it from the wall out-

let and disconnect the antenna or cable system. This will pre-

vent damage to the video product due to lightning and

power-line surges.

15. Power Lines - An outside antenna system should not be

located in the vicinity of overhead power lines or other elec-

tric light or power circuits, or where it can fall into such

power lines or circuits. When installing an outside antenna

system, extreme care should be taken to keep from touching

such power lines or circuits as contact with them might be

fatal.

8. Accessories - Do not place this video

product on an unstable cart, stand, tripod,

bracket, or table. The video product may

fall, causing serious injury to a child or

adult, and serious damage to the appli-

ance. Use only with a cart, stand, tripod,

bracket, or table recommended by the

16. Overloading - Do not overload wall outlets and extension

manufacturer, or sold with the video

cords as this can result in a risk of fire or electric shock.

product. Any mounting of the appliance should follow the

manufacturer's instructions and should use a mounting

accessory recommended by the manufacturer. An appliance

and cart combination should be moved with care. Quick

stops, excessive force, and uneven surfaces may cause the

appliance and cart combination to overturn.

17. Object and Liquid Entry - Never push objects of any kind

into this video product through any openings as they may

touch dangerous voltage points or short-out parts that could

result in a fire or electric shock. Never spill liquid of any

kind on the video product.

18. Servicing - Do not attempt to service this video product

yourself as opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all servicing to

qualified service personnel.

19. Damage Requiring Service - Unplug this video product

from the wall outlet and refer servicing to qualified service

personnel under the following conditions:

a. When the power-supply cord or plug is damaged.

b. If liquid has been spilled, or objects have fallen into the

9. Ventilation - Slots and openings in the cabinet are provided

for ventilation and to ensure reliable operation of the video

product and to protect it from overheating, and these open-

ings must not be blocked or covered. The openings should

never be blocked by placing the video product on a bed,

sofa, rug, or other similar surface. This video product should

not be placed in a built-in installation such as a bookcase or

rack unless proper ventilation is provided or the manufac-

turer's instructions have been adhered to.

10. Power Sources - This video product should be operated

only from the type of power source indicated on the mark-

ing label. If you are not sure of the type of power supply to

your home, consult your appliance dealer or local power

company. For products intended to operate from battery

power, or other sources, refer to the operating instructions.

11. Grounding or Polarization - This video product is

equipped with a polarized alternating-current line plug (a

plug having one blade wider than the other). This plug will

fit into the power outlet only one way. This is a safety fea-

ture. If you are unable to insert the plug fully into the outlet,

try reversing the plug. If the plug should still fail to fit, con-

tact your electrician to replace your obsolete outlet. Do not

defeat the safety purpose of the polarized plug.

12. Power Cord Protection - Power supply cords should be

routed so that they are not likely to be walked on or pinched

by items placed upon or against them, paying particular

attention to cords at plugs, convenience receptacles, and the

point where they exit from the appliance.

video product.

c. If the video product has been exposed to rain or water.

d. If the video product does not operate normally by following

the operating instructions. Adjust only those controls that

are covered by the operating instructions as an improper

adjustment of other controls may result in damage and will

often require extensive work by a qualified technician to

restore the video product to its normal operation.

e. If the video product has been dropped or damaged in any

way.

f. When the video product exhibits a distinct change in perfor-

mance this indicates a need for service.

20. Replacement Parts - When replacement parts are required,

be sure the service technician has used replacement parts

specified by the manufacturer or have the same characteris-

tics as the original part. Unauthorized substitutions may

result in fire, electric shock or other hazards.

21. Safety Check - Upon completion of any service or repairs to

this video product, ask the service technician to perform

safety checks to determine that the video product is in prop-

er operating condition.

22. Heat - This video product should be situated away from heat

sources such as radiators, heat registers, stoves, or other

products (including amplifiers) that produce heat.

13. Outdoor Antenna Grounding - If an outside antenna or

cable system is connected to the video product, be sure the

antenna or cable system is grounded so as to provide some

protection against voltage surges and built-up static charges.

Article 810 of the National Electrical Code, ANSI/NFPA

No. 70, provides information with regard to proper ground-

–

1L25

A NOTE ABOUT RECYCLING

This product’s packaging materials are recyclable and can be reused. Please dispose of all materials in

accordance with your local recycling regulations.

Batteries should never be thrown away or incinerated but disposed of in accordance with your local

regulations concerning chemical wastes.

The serial number of this product may be found on the back of the DVD/VCR COMBINATION UNIT. This ser-

ial number is unique to your machine. You should record the number and other vital information here and retain

this book as a permanent record of your purchase to aid identification in case of theft. Serial numbers are not

kept on file.

Date of Purchase

Dealer Purchase from

Dealer Address

Dealer Phone No.

Model No.

Serial No.

ABOUT COPYRIGHT

Unauthorized copying, broadcasting, public performance and lending of discs are prohibited.

This product incorporates copyright protection technology that is protected by method claims of certain U.S.

patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use

of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for

home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse

engineering or disassembly is prohibited.

SUPPLIED ACCESSORIES

RF Cable

Remote control

Two AA batteries

A/V cables

(NA220UD)

(NA270UD)

(approx. 3 feet (100 cm)

long) (WPZ0102TM015)

WPZ0901TM002

SYMBOLS USED IN THIS MANUAL

The following symbols below appear in some headings and notes in this manual, with the following meanings

VCR

: Description refers to playback of video cassette tapes.

DVD-V

: Description refers to playback of DVD video discs.

: Description refers to playback of audio CDs.

MP3

: Description refers to playback of MP3 discs.

QUICK

: Description refers to the items to be set in the QUICK mode.

–

1L25

TABLE OF CONTENTS

ꢀ LASER SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

ꢀ PLAYING A DISC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

BASIC PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

GENERAL FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

PAUSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

DISC MENU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

TITLE MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

STEP BY STEP PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . 23

RESUME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

FAST FORWARD / REVERSE SEARCH . . . . . . . . . . . . . . . 23

SLOW FORWARD / SLOW REVERSE . . . . . . . . . . . . . . . . 23

ZOOM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

TRACK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

TITLE / CHAPTER SEARCH. . . . . . . . . . . . . . . . . . . . . . . . 24

TIME SEARCH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

PROGRAM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

RANDOM PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

MP3 PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

ON-SCREEN INFORMATION . . . . . . . . . . . . . . . . . . . . . . . 26

TRACK SELECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

RANDOM PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

PROGRAM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

AUDIO LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

STEREO SOUND MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

SUBTITLE LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

CAMERA ANGLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

CHANGING THE ON-SCREEN DISPLAY . . . . . . . . . . . . . 28

PARENTAL CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

MARKER SETUP SCREEN . . . . . . . . . . . . . . . . . . . . . . . . . 29

ꢀ DVD SETUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

AUDIO SETTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

BLACK LEVEL SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . 30

VIRTUAL SURROUND . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

DISPLAY SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

LANGUAGE SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

ꢀ TROUBLESHOOTING GUIDE. . . . . . . . . . . . . . . . . . . . . . 32

ꢀ MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

ꢀ SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

ꢀ IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . 3

ABOUT COPYRIGHT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

SUPPLIED ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . 4

SYMBOLS USED IN THIS MANUAL. . . . . . . . . . . . . . . . . . 4

ꢀ FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

ꢀ PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

ꢀ ABOUT THE DISCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

PLAYABLE DISCS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

DISC TYPES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

ꢀ OPERATING CONTROLS AND FUNCTIONS. . . . . . . . . . . 8

DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

DISPLAYS DURING OPERATION . . . . . . . . . . . . . . . . . . . 11

LOADING THE BATTERIES . . . . . . . . . . . . . . . . . . . . . . . . 11

ꢀ VCR/DVD SWITCHING . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

ꢀ HOOKUPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

CONNECTING TO A TV WITHOUT A/V TERMINALS. . . 13

CONNECTING TO A TV WITH A/V TERMINALS. . . . . . . 13

CONNECTING TO A TV THAT HAS AN S-VIDEO INPUT

JACK OR COMPONENT VIDEO IN JACKS. . . . . . . . . . . . 14

CONNECTING TO A STEREO AMPLIFIER EQUIPPED

WITH DIGITAL INPUT JACKS SUCH AS MD DECK OR

DAT DECK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

CONNECTING TO A RECEIVER WITH

DOLBY DIGITAL DECODER . . . . . . . . . . . . . . . . . . . . . . . 15

CONNECTING TO AN ANALOG AUDIO SYSTEM. . . . . . 15

ꢀ SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

AUTOMATIC CHANNEL SET UP. . . . . . . . . . . . . . . . . . . . 16

TO CHANGE THE ON-SCREEN LANGUAGE. . . . . . . . . . 17

CLOCK SET UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

ꢀ PLAYBACK FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

NORMAL PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

AUTO REPEAT PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . 18

SEARCH FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

ꢀ RECORDING FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . 19

NORMAL RECORDING . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

OTR (One Touch Recording). . . . . . . . . . . . . . . . . . . . . . . . . 19

TIMER RECORDING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

HINTS FOR TIMER RECORDING . . . . . . . . . . . . . . . . . . . 20

ꢀ SPECIAL FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

COPYING A VIDEO TAPE. . . . . . . . . . . . . . . . . . . . . . . . . . 21

MTS (Multi-Channel Television Sound) SYSTEM . . . . . . . . 21

AUTO REWIND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

REAL TIME TAPE COUNTER. . . . . . . . . . . . . . . . . . . . . . . 22

–

1L25

FEATURES

¡Virtual Surround Sound

DVD

Mode

¡Component Video Out Jacks

¡Dolby Digital sound

This DVD/VCR COMBINATION UNIT can output a

Dolby Digital audio signal.

Jacks located on the back of the DVD/VCR COMBINA-

TION UNIT which are used to send high-quality video to

a TV via Component Video In Jacks.

¡Still/fast/slow/step playback

¡Bit rate indication

¡Random playback for audio CD and MP3

¡Program playback for audio CD and MP3

¡DVD menus in a desired language

¡DRC (Dynamic range control)

You can control the range of sound volume.

¡Black Level Setting

¡Screen saver/Auto power-off functions

The screen saver program starts when there is no input

from the player for five minutes in the stop mode. When

the screen saver program is activated for 30 minutes, the

power automatically turns off.

VCR

Mode

Hardware specifications

¡Auto Head Cleaner

¡4 Head HiFi Stereo

¡Subtitles in a desired language

¡Selecting a camera angle

¡Trilingual on-screen menu display selectable in

English, French, or Spanish

¡Choices for audio language and sound mode

¡Parental lock

¡181 channel capability PLL frequency synthesiz-

er tuner with direct station call

(A cable converter box may be necessary to view scram-

bled cable channels.)

¡Automatic detection of discs

This player automatically detects if the loaded disc is

DVD, audio CD or MP3 on disc.

Automatic functions

¡Playback MP3 disc

¡Auto power on system

Automatically turns the VCR on when you insert the cas-

sette.

¡Direct Search

¡On-screen display

¡Digital Auto Tracking (DTR)

Information about the current operation can be displayed

on the TV screen, allowing you to confirm the currently

active functions (such as program playback), on the TV

screen using the remote control.

Playback

¡Auto Repeat

¡2 Step Picture Search Operation

¡Index Search

¡Search

Chapter search / Title search / Track search / Time search

¡Time Search

¡Repeat

Chapter / Title / Track / Group / All / A-B

Recording

¡Zoom

¡1Year, 8 events (including Daily and WeeklyTimer

Recording)

¡Marker

The part designated by user can be called back.

¡OTR (One Touch Recording)

¡Resume Play

PRECAUTIONS

AVOID THE HAZARDS OF

INSTALLATION LOCATION

ELECTRICAL SHOCK AND FIRE

For safety and optimum performance of your

DVD/VCR COMBINATION UNIT:

• Do not handle the power cord with wet hands.

• Do not pull on the power cord when disconnecting it

from AC wall outlet. Grasp it by the plug.

• If, by accident, water is spilled on your DVD/VCR

COMBINATION UNIT, unplug the power cord imme-

diately and take the unit to our Authorized Service

Center for servicing.

• Install the DVD/VCR COMBINATION UNIT in a hor-

izontal and stable position. Do not place anything

directly on top of the DVD/VCR COMBINATION

UNIT. Do not place the DVD/VCR COMBINATION

UNIT directly on top of the TV.

• Shield it from direct sunlight and keep it away from

sources of intense heat. Avoid dusty or humid

places. Avoid places with insufficient ventilation for

proper heat dissipation. Do not block the ventilation

holes on the sides of the DVD/VCR COMBINATION

UNIT. Avoid locations subject to strong vibration or

strong magnetic fields.

• Do not put your fingers or objects into the DVD/VCR

COMBINATION UNIT cassette holder.

MOISTURE CONDENSATION WARNING

Moisture condensation may occur inside the unit when

it is moved from a cold place to a warm place, or after

heating a cold room or under conditions of high

humidity. Do not use the DVD/VCR COMBINATION

UNIT at least for 2 hours until its inside is dry.

–

1L25

ABOUT THE DISCS

PLAYABLE DISCS

DISC TYPES

The following discs can be played back on this

DVD/VCR COMBINATION UNIT.

[

]

DVD

Data on a DVD is divided into sections called "titles", and

then into subsections called "chapters", each of which is

given a title or chapter number. Playback conditions are

preset on some DVD video discs, and these playback con-

ditions take priority over user operations on this player. If

a function you selected does not run as desired, refer to

the manual accompanying the disc.

DVD video

DVD+R/RW*

CD-R/RW*

DVD-R/RW*

Audio CD

MP3*

* Depending on the types or the writing method of the

medium some discs can not be played.

Example

• Some DVD-R/RW, DVD+R/RW, or CD-R/RW discs

made on personal computers, or on DVD recorders may

not be played back properly due to factors such as

scratches, dirt or special properties of the disc.

Title 1

Title 2

Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2

• Discs made on personal computers may not be played

back properly due to different environments or the set-

tings of the application you use. We recommend always

to use the standardized, properly formatted discs.

(Please contact the sales agency for more detail).

[

]

AUDIO CD

This player conforms to the NTSC color system. You can-

not play discs recorded in other color systems such as

PAL or SECAM.

Data on an audio CD is divided into sections called

“tracks”, each of which is given a track number.

¡Some discs include region codes as shown below.

Example

Track 1

Track 2

Track 3

Track 4

Track 5

Track 6

¡The number inside the symbol refers to a region of the

world, and a disc encoded in a specific region format

can only be played back on DVD/VCR COMBINA-

TION UNIT with the same region code.

The following discs cannot be played back on this

DVD/VCR COMBINATION UNIT.

[

]

MP3

Data on an MP3 is divided into sections called "groups",

and then into subsections called "tracks", each of which is

given a group or track number.

DVD with region codes other than 1 or ALL.

DVD-ROM

Example

Group 1

Group 2

DVD-RAM (Never play back, otherwise malfunc-

tion may result.)

Track 1

Track 2

Track 3

Track 4

Track 1

Track 2

CD-ROM

VSD

CDV (Only plays back the audio part.)

CD-G (Only plays back the sound.)

CD-I (Never play back, otherwise malfunction

may result.)

SACD

Photo CD (Never play back, otherwise malfunc-

tion may result.)

Any other discs without compatibility indications.

–

1L25

OPERATING CONTROLS AND FUNCTIONS

FRONT PANEL

6 7

POWER

OPEN/CLOSE

CHANNEL

STOP/EJECT

PLAY

DVD

VCR

VIDEO

AUDIO

OUTPUT

DVD

VCR TIMER REC REC

STOP

PLAY

REW

F.FWD

18 16 14

17 15

REMOTE CONTROL

7. POWER Light

This light appears when the power is on.

8. STOP/EJECT Button (VCR)

EJECT Button

POWER SPEED AUDIO

Press to remove the tape from the VCR.

STOP Button

SKIP/CH.

Press to stop the tape motion.

9. PLAY Button(VCR) [page 18]

Press to begin playback.

VCR/TV

SLOW

10. CHANNEL Buttons [page 16]

In VCR mode, press to change TV channels on the

VCR; press to adjust the tracking during normal or slow

motion playback; press to remove vertical jitter in a Still

picture.

DISPLAY DVD

VCR

PAUSE

PLAY

STOP

11. AUDIO In Jacks [page 21]

Connect audio cables coming from the audio out jacks

of a camcorder, another VCR, or an audio source here.

12. VIDEO In Jack [page 21]

RECORD

Connect a video cable coming from the video out jack

of a camcorder, another VCR, or a video source (laser

disc player, camcorder, etc.) here.

ENTER

SETUP

TITLE

RETURN

MODE

CLEAR/

13. F.FWD Button (VCR) [page 18]

Press to rapidly advance the tape, or view the picture

rapidly in forward during playback. (Forward Search).

14. REW Button (VCR) [page 18]

MODE ZOOM

C.RESET

SUBTITLE ANGLE REPEAT

T-SET

Press to rewind the tape, or to view the picture rapidly

in reverse during the playback mode (Rewind Search).

15. REC/OTR Button [page 19]

1. Disc loading tray

2. OPEN/CLOSE Button [page 22]

Press once to start a recording. Press repeatedly to start

a One-Touch Recording.

Press to insert discs into or remove them from the tray.

3. DVD OUTPUT Light (Green) [page 12]

16. REC Light [page 19]

This light appears when the DVD output mode is select-

Lights up during recording.

ed. You can only watch DVDs when the green DVD 17. TIMER REC Light [page 20]

OUTPUT light is on. To make the green DVD OUT-

PUT light come on, press DVD on the remote control or

OUTPUT on the front panel.

This light appears when the DVD/VCR is in standby

mode for a timer recording or during a One-Touch

Recording. It flashes if T-SET is pressed for a timer

recording, but there is no tape in the DVD/VCR. It

flashes when all timer recordings or One-Touch

Recordings are finished.

4. VCR OUTPUT Light (Green) [page 12]

This light appears when the VCR output mode is select-

ed. You can only watch tapes when the green VCR

OUTPUT light is on. To make the green VCR OUTPUT

light come on, VCR on the remote control or OUTPUT

on the front panel.

5. CASSETTE COMPARTMENT

6. POWER Button [page 16]

Press to turn the power on and off.

–

8 –

1L25

18. OUTPUT Button [page 12]

32. TITLE Button [page 23]

Press to select DVD mode or VCR mode.

GYou can switch the output mode either by pressing

33. SETUP Button [pages 28-31]

Press to enter DVD player setup mode.

OUTPUT on the front panel, or by pressing DVD or 34. ZOOM Button [page 24]

VCR on the remote control. However, if you press

Enlarges part of a DVD-reproduced image.

OUTPUT on the front panel first, you need to re- 35. MODE Button [pages 26, 27, and 30]

select the corresponding mode by pressing DVD or

VCR on the remote control.

Activates program playback or random playback mode

when playing CDs or MP3. Sets Black level and virtual

surround.

19. Remote Sensor Window

20. Display

36. SUBTITLE Button [page 27]

Press to select the desired subtitle language.

36. T-SET Button [page 20]

21. PLAY Button (DVD) [page 22]

Press to begin playback.

22. STOP Button (DVD) [page 22]

Press to put the VCR into standby mode for a timer

recording.

Stops operation of the disc.

23. SPEED Button [page 19]

Press to select the VCR’s recording speed (SP or SLP)

24. POWER Button

37. ANGLE Button [page 27]

Press to change the camera angle to see the sequence

being played back from a different angle.

38. REPEAT Button [page 25]

Repeats playback of the current disc, title, chapter or

track.

Press to turn the power on and off.

25. Number Buttons

GDVD mode [page 24]

Press to select numbered items in a menu.

+10

Use this button to enter number 10 and above.

GVCR mode [page 16]

39. A-B REPEAT Button [page 25]

Repeats playback of a selected section.

40. SEARCH MODE Button

GDVD mode [page 24]

Press to select TV channels on the VCR.

To select channels, enter channel numbers as a two-

digit number for the quickest results. For example, to

select channel 6, press 0 then 6.

26. DISPLAY Button

Press to access or remove the Search display,

which allows you to go directly to a specific

Title/Chapter/Track/Time.

GVCR mode [page 18]

Press to perform a Time Search or an Index Search.

41. CLEAR/C.RESET Button

GDVD mode [pages 24, 25]

GDVD mode [page 28]

Press to access or remove the display screen during

DVD or Audio CD playback.

GVCR mode [page 21]

Press to access or remove the VCR’s on-screen status

display.

Press to reset the setting.

GVCR mode [page 18]

Press to reset the counter. Press to exit from the

MENU screen.

27. DVD Button [page 12]

42. RETURN Button [page 30]

Press to select DVD mode for the remote control.

GYou can switch the OUTPUT mode either by pressing

GDVD mode

Returns to the previous operation.

OUTPUT on the front panel, or by pressing DVD or 43. Arrow Buttons

VCR on the remote control. However, if you press

OUTPUT on the front panel first, you need to re-

select the corresponding mode by pressing

DVD or VCR on the remote control.

Use when making settings while watching the display

on a TV screen.

GVCR mode [page 16]

p/o Buttons

28. h Button

Press to enter digits when setting program (For exam-

ple: setting clock or timer program). Press to select

the setting modes from the on screen menu.

B Button

GDVD mode [page 23]

Press to view the DVD picture in fast reverse motion.

Press PAUSE, then press this button to begin slow

motion playback. Press this button repeatedly to

change the reverse speed of slow motion.

GVCR mode [page 18]

When setting program (For example: setting clock or

timer program), press to determine your selection and

proceed to the next step you want to input. Press to

determine the setting modes from the on screen

menu. Press to add or delete channel numbers during

channel preset.

Press to rewind the tape, or to view the picture rapid-

ly in reverse during the playback mode (Rewind

Search).

29. STOP Button

s Button

GDVD mode

Press to cancel a setting of timer program. Press to

correct digits when setting program (For example:

setting clock or timer program). Press to add or delete

channel numbers during channel preset.

44. ENTER Button

Press to stop the disc motion.

GVCR mode

Press to stop the tape motion.

30. RECORD Button [page 19]

Press once to start a recording.

31. MENU Button

GDVD mode [page 22]

Press to accept a setting.

GDVD mode [page 23]

Press to display the menu of the Disc.

GVCR mode [page 17]

Press to access the VCR menu.

–

1L25

49. SLOW Button [page 18]

During tape playback, press to view the video tape in

slow motion. Press again to resume normal playback.

This button does not affect DVD playback.

50. VCR/TV Button [page 19]

Use to select VCR or TV position.

GVCR Position

45. g Button

GDVD mode [page 23]

Press to fast forward the Disc. Press PAUSE, then

press this button to begin slow motion playback.

Press this button repeatedly to change the forward

speed of slow motion.

GVCR mode [page 18]

To view playback, to monitor video recordings or to

watch TV using the VCR tuner.

GTV Position

To watch TV or to view one program while recording

another.

Press to rapidly advance the tape, or view the picture

rapidly in forward during playback (Forward Search).

46. PLAY Button

GDVD mode

Press to begin playback.

51. SKIP/CH. Buttons

GVCR mode

GDVD mode

Press to begin playback.

Press to skip Chapters or Tracks.

GVCR mode

47. VCR Button [page 12]

Press to select VCR mode for the remote control.

GYou can switch the OUTPUT mode either by pressing

OUTPUT on the front panel, or by pressing DVD or

VCR on the remote control. However, if you press

OUTPUT on the front panel first, you need to re-

select the corresponding mode by pressing DVD or

VCR on the remote control.

Press to change TV channels on the VCR.

52. AUDIO Button [page 27]

Press to select a desired audio language or sound mode.

48. PAUSE Button

Notes

GDVD mode [page 22]

¡To use the remote control to operate the DVD/VCR

COMBINATION UNIT and its features, press DVD

on the remote control before pressing other DVD’s

operation buttons. Verify that the green DVD OUT-

PUT Light is on.

Press to pause Disc playback. Press repeatedly to

advance the DVD picture step by step (or one frame

at a time).

GVCR mode [page 19]

While recording, press to temporarily stop the record-

ing (pause). Press a second time to resume normal ¡To use the remote control to operate the VCR and its

recording. You can not pause

One-Touch

features, press VCR on the remote control before

pressing other VCR’s operation buttons. Verify that

the green VCR OUTPUT Light is on.

Recording. Or, press during tape playback to freeze

the picture. Press to advance the picture one frame at

a time during still mode.

REAR VIEW

54 55

DVD

DVD/VCR

VCR

AUDIO OUT AUDIO IN

S-VIDEO COMPONENT AUDIO

DIGITAL

AUDIO OUT

OUT

VIDEO OUT

OUT

ANT-IN

COAXIAL

ANT-OUT

VIDEO OUT VIDEO IN

53. ANT-IN (Antenna In) Jack

56.AC Power Cord

Connect your antenna, Cable Box, or Satellite decoder

box.

Connect to a standard AC outlet to supply power to the

DVD/VCR COMBINATION UNIT.

DVD Playback only

54. DVD/VCR AUDIO OUT Jacks

Connect the supplied audio cables here and to the Audio

In jacks of a television or other audio equipment.

55. AUDIO IN Jacks

57. COMPONENT VIDEO OUT Jacks

Connect optional component video cables here and to

the component Video In jacks of a television.

58. COAXIAL Jack

Connect audio cables coming from the audio out jacks

of a camcorder, another VCR, or an audio source here.

Connect an optional coaxial digital audio cable here and

to the Coaxial Digital Audio In jack of a decoder or

audio receiver.

–

1L25

59. DVD ANALOG AUDIO OUT Jacks

Connect the supplied audio cables here and to the Audio

In jacks of a television or other audio equipment (DVD

only).

62. DVD/VCR VIDEO OUT Jack

Connect the yellow video cable (supplied) here and to

the TV’s Video In jack.

63. ANT-OUT (Antenna Out) Jack

Use the supplied RF coaxial cable to connect this jack

to the ANTENNA IN Jack on your TV.

60. S-VIDEO OUT Jack

Connect an optional S-Video cable here and to the S-

Video In jack of a television. (DVD only)

61. VIDEO IN Jack

Caution: Do not touch the inner pins of the jacks on

the rear panel. Electrostatic discharge may cause

permanent damage to the player.

Connect a cable coming from the video out jack of a

camcorder, another VCR, or an audio-visual source

(laser disc player, video disc player, etc.) here.

DISPLAY

DISPLAYS DURING OPERATION

DVD

Lights up when a DVD

is inserted into the tray.

No disc inserted or playing

DVD menu

Stays on when the

Stays on when repeat

A-B repeat function

track function is on.

is on.

Tray open

Stays on when

Stays on when the

repeat chapter

repeat function is on.

function is on.

Tray closed

Stays on when

repeat title

function is on.

Loading the Disc

LOADING THE BATTERIES

1. Open the battery compartment

cover.

Lights up when the

Lights up when a

inserted disc comes

CD is inserted into

to a pause.

the tray.

Stays on when the inserted

disc is being played back.

Displays how long a current title

2. Insert two AA batteries, with each

one oriented correctly.

or track has been played back. When

a chapter or track has switched, the

number of a new title, chapter or

track is displayed.

3. Close the cover.

VCR

Stays on during playback

when the repeat function

is on.

Notes

¡Do not mix alkaline and manganese batteries.

¡Do not mix old and new batteries.

Lights up when the playback

is in a still or in a slow mode.

Works as a clock, or a tape counter.

Also displays a channel number,

and remaining time for OTR

Stays on when the inserted

cassette is being played back.

–

1L25

VCR/DVD SWITCHING

Because this product is a combination of a VCR and DVD player, you must first select

which component you wish to operate with the OUTPUT BUTTON.

VCR MODE

DVD MODE

Press VCR on the remote control.

(Verify that the VCR OUTPUT Light is lit.)

Press DVD on the remote control.

(Verify that the DVD OUTPUT Light is lit.)

Notes

¡Pressing only OUTPUT on the front panel does not switch the mode of the remote control. You always need

to select the correct mode on the remote control too.

POWER

OPEN/CLOSE

CHANNEL

STOP/EJECT

PLAY

POWER SPEED AUDIO

DVD

VCR

VIDEO

AUDIO

OUTPUT

DVD

VCR TIMER REC REC

STOP

PLAY

REW

F.FWD

SKIP/CH.

VCR/TV

SLOW

DVD button

DVD OUTPUT Light

DISPLAY DVD

VCR

PAUSE

VCR button

OUTPUT

PLAY

STOP

DVD

VCR TIM

RECORD

VCR OUTPUT Light

ENTER

SETUP

TITLE

RETURN

MODE

CLEAR/

MODE ZOOM

C.RESET

OUTPUT button

SUBTITLE ANGLE REPEAT

T-SET

–

1L25

HOOKUPS

CAUTION:

¡Be sure to turn off the DVD/VCR COMBINATION UNIT and equipment to be connected.

¡Read through the operation manual for the equipment to be connected.

¡Be sure that the colors of the jacks and plugs match up when using VIDEO/AUDIO cables.

¡Be sure to keep the DVD/VCR COMBINATION UNIT connection cables separate from the TV antenna cable

when you install the DVD/VCR COMBINATION UNIT, because it may cause electrical interference when you

are watching television programs.

CONNECTING TO A TV WITHOUT A/V TERMINALS

1. Disconnect the AC power cord of the TV from the

[VHF/UHF

[Back of the DVD/VCR]

[Indoor antenna]

AC outlet.

combination antenna]

[Back of the

UHF/VHF combination TV]

2. Disconnect the antenna or cable from the TV.

3. Connect the antenna or cable to the ANT-IN jack of

the DVD/VCR COMBINATION UNIT.

4. Connect the DVD/VCR COMBINATION UNIT to

the TV using the RF cable.

5. Plug the AC power cords of the DVD/VCR COM-

BINATION UNIT and TV into the AC outlets.

RF cable

(supplied)

DVD/VCR

VCR

AUDIO OUT AUDIO IN

ANT-IN

UHF/VHF

[Cable box or satellite box]

ANT-OUT

VIDEO OUT VIDEO IN

OUT

From Cable or

Satellite Company

RF OUTPUT CHANNEL for DVD/VCR

1. Connect the DVD/VCR COMBINATION UNIT to a TV using RF cable (see above steps).

2. Select channel 3 on your TV.

3. Press PLAY.

¡If noise appears, change the RF output channel of the DVD/VCR COMBINATION UNIT to channel 4 by

pressing PLAY on the VCR for 3 seconds during playback.

There is case that the RF output channel does not change by situation (For example, when you adjust tracking using

(

)

CHANNEL

In this case, stop the playback, and start the playback again. After that, press PLAY on the VCR for 3 seconds.

If there is a power failure or the DVD/VCR COMBINATION UNIT is unplugged for more than 30 seconds, the RF

output channel setting will return to CH3

Note to CATV system installer

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that pro-

vides guidelines for proper grounding and, in particular, specifies that the cable ground should be connected

to the grounding system of the building, as close to the point of cable entry as practical.

CONNECTING TO A TV WITH A/V TERMINALS

DVD

DVD/VCR

VCR

AUDIO OUT AUDIO IN

S-VIDEO COMPONENT AUDIO

DIGITAL

OUT

VIDEO OUT

OUT

AUDIO OUT

Antenna/Cable signal

ANT-IN

A/V-compatible or

wide screen TV

COAXIAL

ANT-OUT

VIDEO OUT VIDEO IN

To ANT. IN

of TV

To VIDEO INPUT jack

To Right (red) and Left (white)

To AUDIO INPUT jacks

To VIDEO OUT jack

[Fig. 1]

To AUDIO OUT jacks

Notes

¡Connect the DVD/VCR COMBINATION UNIT directly to a TV. If the A/V cables are connected into a

VCR first, picture may be distorted due to the copy protection system.

–

1L25

CONNECTING TO A TV THAT HAS AN S-VIDEO INPUT JACK OR

COMPONENT VIDEO IN JACKS

FOR TVs WITH S-VIDEO INPUT JACK

Use an S-Video cable (commercially available) in place of the yellow video cable to enjoy higher quality pic-

tures.

The S-Video connection only supplies video (picture) in the DVD mode of the DVD/VCR COMBINATION

UNIT. Therefore, in order to use the VCR features or view TV channels on the DVD/VCR COMBINATION

UNIT, you still need to either connect the RF cable between the ANT-OUT jack of the DVD/VCR COMBINA-

TION UNIT and the TV’s Antenna In jack, or connect the yellow video cable as described earlier (Fig.1). To

connect the supplied RF cable, see page 13.

DVD

DVD/VCR

VCR

AUDIO OUT AUDIO IN

S-VIDEO COMPONENT AUDIO

DIGITAL

AUDIO OUT

OUT

VIDEO OUT

OUT

ANT-IN

A/V-compatible or

wide screen TV

COAXIAL

ANT-OUT

VIDEO OUT VIDEO IN

To S-VIDEO INPUT jack

To S-VIDEO OUT jack

To Right (red) and Left (white)

To AUDIO INPUT jacks

[Fig. 2]

To AUDIO OUT jacks

FOR TVs WITH

COMPONENT VIDEO IN JACKS

Use a component video cable (commercially available) in place of the yellow DVD/VCR video cable and S-

VIDEO jack to enjoy higher quality pictures.

The component video connection only supplies video (picture) in the DVD mode of the DVD/VCR COMBI-

NATION UNIT. Therefore, in order to use the VCR features or view TV channels at the DVD/VCR COMBI-

NATION UNIT, you still need to either connect the RF coaxial cable between the ANT-OUT jack of the

DVD/VCR COMBINATION UNIT and the TV’s Antenna In jack, or connect the yellow VCR video cable as

described earlier (Fig. 1). To connect the supplied RF cable, see page 13.

To Right (red) and Left (white)

AUDIO OUTPUT jacks

To Right (red) and Left (white)

AUDIO INPUT jacks

A/V-compatible

wide screen TV

DVD

DVD/VCR

VCR

AUDIO OUT AUDIO IN

S-VIDEO COMPONENT AUDIO

DIGITAL

OUT

VIDEO OUT

OUT

AUDIO OUT

ANT-IN

COAXIAL

ANT-OUT

VIDEO OUT VIDEO IN

To COMPONENT VIDEO

INPUT jacks

To COMPONENT VIDEO

OUT jacks

[Fig. 3]

CONNECTING TO A STEREO AMPLIFIER EQUIPPED WITH

DIGITAL INPUT JACKS SUCH AS MD DECK OR DAT DECK

Use an audio coaxial digital cable (commercially available) for the audio connections.

Connecting to an amplifier equipped with digital input jacks such as MD Deck or DAT Deck.

DVD

DVD/VCR

VCR

AUDIO OUT AUDIO IN

S-VIDEO COMPONENT AUDIO

DIGITAL

AUDIO OUT

(Stereo Receiver)

Amplifier equipped with digital

input jacks, MD deck,

DAT deck, etc.

OUT

VIDEO OUT

OUT

ANT-IN

COAXIAL

ANT-OUT

VIDEO OUT VIDEO IN

To COAXIAL DIGITAL

AUDIO OUT jack

[Fig. 4]

To COAXIAL DIGITAL AUDIO INPUT jack

Notes

¡The audio source on a disc in the 5.1 channel Dolby Digital surround format cannot be recorded as digital

sound by an MD or DAT deck.

¡Set DOLBY DIGITAL to OFF for audio output in the setup mode. Playing a DVD disc using incorrect set-

tings may generate noise distortion, and may also damage the speakers. (See page 29 to set DOLBY DIGITAL

to OFF.)

–

1L25

CONNECTING TO A RECEIVER WITH DOLBY DIGITAL DECODER

If using this DVD/VCR COMBINATION UNIT to play a DVD disc in 5.1 channel Dolby Digital surround, the

DVD/VCR COMBINATION UNIT outputs a Dolby Digital data stream from its COAXIAL DIGITAL AUDIO

OUT jack. By hooking the DVD/VCR COMBINATION UNIT up to a Dolby Digital receiver, you can enjoy a

more convincing, realistic ambience with powerful and high-quality surround sound as heard in movie theaters.

Use an audio coaxial digital cable (commercially available) for the audio connections.

DVD

DVD/VCR

VCR

AUDIO OUT AUDIO IN

S-VIDEO COMPONENT

DVD

DIGITAL

AUDIO OUT

OUT

VIDEO OUT AUDIO OUT

ANT-IN

COAXIAL

ANT-OUT

VIDEO OUT VIDEO IN

Center speaker

Front speaker

(right)

Front speaker

(left)

To COAXIAL DIGITAL

AUDIO OUT jack

Receiver with

Dolby Digital Decoder

To COAXIAL DIGITAL

AUDIO INPUT jack

Subwoofer

Surround

speaker

(left)

Surround

speaker

(right)

[Fig. 5]

¡If the output is Dolby Digital audio, connect to a Dolby Digital decoder, and set Dolby Digital to ON for audio

output in the setup mode.

Unless connected to a Dolby Digital receiver, set DOLBY DIGITAL to OFF for audio output in the setup mode.

Playing a DVD using incorrect settings may generate noise distortion, and may also damage the speakers

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of

Dolby Laboratories.

CONNECTING TO AN ANALOG AUDIO SYSTEM

DVD

DVD/VCR

VCR

AUDIO OUT AUDIO IN

S-VIDEO COMPONENT

DVD

DIGITAL

OUT

VIDEO OUT AUDIO OUT

AUDIO OUT

To AUDIO OUT jacks

ANT-IN

COAXIAL

ANT-OUT

VIDEO OUT VIDEO IN

Stereo system

To Right (red) and Left (white)

AUDIO INPUT jacks

To ANALOG AUDIO INPUT jacks

To Right (red) and Left (white)

ANALOG AUDIO OUT jacks

[Fig. 6]

Notes

¡Be sure to turn off the power to all components in the system before connecting another component.

¡Refer to the Owner's Manuals for stereo systems and any other components to be connected to the DVD/VCR

COMBINATION UNIT.

–

1L25

SETUP

AUTOMATIC CHANNEL SET UP

After scanning, the tuner stops on the low-

est memorized channel. The TV screen

returns to TV mode.

VCR

You can automatically program the tuner to scan only

the channels you receive in your area.

¡If “AUTO SET UP” appears on the TV screen again,

check the cable connections. Press B once again and

the VCR will begin preset again.

¡Channel memory programming is NOT needed

when you connect the VCR to a cable box or a satel-

lite box as in "CONNECTING TO A TV WITHOUT

A/V TERMINALS" on page 13. In this case, select

channel 3 on your TV. Then, the channel you want to

record or view may be selected at the cable box or

satellite box.

¡If noise appears, change the RF output channel of

the VCR to channel 4 by pressing PLAY for 3 sec-

onds during playback. Then select the same chan-

nel (CH4) on your TV.

TO SELECT A DESIRED CHANNEL

You can select the desired channel by using CHAN-

NEL (o/p) or by directly pressing Number on the

remote control.

Note for using the Number:

¡When selecting cable channels which are higher

than 99, enter channel numbers as a three-digit num-

ber.(For example: 117, press 1,1,7)

¡You must precede single-digit channel numbers with

a zero (For example: 02, 03, 04 and so on).

¡Follow the steps below once. Repeat only if there

is a power failure or if the VCR is unplugged for

more than 30 seconds. (In these cases, the pro-

grammed channels are erased.)

¡You must follow the steps below before attempting

to play or record a video tape. If you want to play

or record a video tape BEFORE programming the

tuner, you can cancel it by pressing

TO PRESET THE CHANNELS AGAIN

Press MENU until the main menu appears.

(If you have already set the clock, you only

have to press it once. If not, you have to

press it twice).

CLEAR/C.RESET.

You need to connect the antenna or cable to

the VCR first. Then, connect the DVD /VCR

power plug to a standard AC outlet.

Select “CHANNEL SET UP” by pressing

or L. Then, press B.

Turn on the TV and set the TV to channel 3.

¡If noise appears, change the RF output channel of

the VCR to channel 4 by pressing PLAY for 3 sec-

onds during playback. Then select the same chan-

nel (CH4) on your TV. (See “RF OUTPUT

CHANNEL” on page 13 for the detail.)

Select “AUTO SET UP” by pressing K or L.

Then, press B.

¡After scanning, the tuner stops on the lowest memo-

rized channel.

Turn on the VCR by pressing POWER. the

POWER light will come on.

Select the On Screen Language (“ENG-

LISH”, “FRANÇAIS” or

“ESPAÑOL”) by pressing

or L. Then, press B.

5 Begin channel preset by pressing B once.

The tuner scans and memorizes all active

channels in your area.

CH 01

¡The VCR distinguishes between

standard TV channels and cable

channels.

AUTO SET UP

–

1L25

TO ADD/DELETE CHANNELS

CLOCK SET UP

When scanning, some channels may be skipped due to

a weak signal. In such cases, you can add the channels

to the VCR memory manually.

VCR

Select main menu by pressing MENU.

Press MENU until the main menu appears.

¡If the clock is not set, the CLOCK SET menu

appears first. In this case, follow step [3].

(If you have already set the

- MENU -

TIMER PROGRAMMING

[OFF]

AUTO REPEAT

CHANNEL SET UP

CLOCK SET

clock, you only have to

press it once. If not you

have to press it twice).

LANGUAGE SELECT

AUDIO OUT

[ON]

TV STEREO

SAP

Select "CLOCK SET" by pressing K or L.

Then, press B.

Set the clock.

Select "CHANNEL SET UP" by pressing

or L. Then, press B.

1) Set the month

Select "MANUAL SET UP" by pressing K or

L. Then, press B.

Press K or L repeatedly.

Then, press B.

Enter the desired channel number by press-

ing K or L.

2) Set the day

Press K or L repeatedly.

Then, press B.

Add or Delete it from memory by pressing

B or s so that "ADD" or "DELETE" flashes

on the TV screen accordingly.

3) Set the year

Press K or L repeatedly.

Then, press B.

The day of the week will appear automatically.

Exit the Preset mode by pressing

CLEAR/C.RESET.

4) Set the hour

Press K or L repeatedly.

Then, press B.

TO CHANGE THE ON-SCREEN

LANGUAGE

5) Set the minute

Press K or L repeatedly.

Then, press B.

VCR

Press MENU twice to call up the main

menu. (If you have already set the clock,

you only have to press it once).

6) Set AM or PM

CLOCK SET

MONTH DAY

YEAR

Press K or L repeatedly.

03 17 MON 2003

HOUR MINUTE AM/PM

PM AM

Select "LANGUAGE SELECT" by pressing

or L. Then, press B.

¡To go back one step, press s.

Select "ENGLISH", "FRANCAIS" or

"ESPAÑOL" by pressing K or L. Then, press

CLEAR/C.RESET.

Start the clock by pressing

CLEAR/C.RESET or B.

¡If you accidentally select Spanish or French and

need English: Press MENU and choose SELEC.

IDIOMA, or SELECTION LANGUE. Press B,

and select ENGLISH by pressing K or L.

Finally, press CLEAR/C.RESET.

–

1L25

PLAYBACK FUNCTION

NORMAL PLAYBACK

Select "AUTO REPEAT" by pressing K or L.

VCR

Begin auto repeat playback by pressing

so that ON appears next to "AUTO

REPEAT".

Insert a prerecorded tape. The VCR will turn

on.

¡If the safety tab has been removed, the

VCR will start playback automatically.

If the on-screen menu still remains, CLEAR/C.RESET

to exit the menu.

¡To cancel the Auto repeat mode, press B at step [3]

so that OFF appears next to "AUTO REPEAT".

Turn on the TV and set the TV to channel 3.

If noise appears, change the RF output channel of the

VCR to channel 4 by pressing PLAY for 3 seconds dur-

ing playback. Then select the same channel (CH4) on

your TV. (See “RF OUTPUT CHANNEL” on page 13

for the detail.)

SEARCH FUNCTIONS

VCR

PICTURE SEARCH

Begin playback by pressing PLAY.

If you want to skip or repeat a scene during playback,

press D or E.

¡Tracking adjustment will be done automatically

(Digital Tracking function) when you start playback.

To adjust the tracking manually, press SKIP/CH. on

the remote or CHANNEL (o/p) on the VCR.

¡Press it again and the VCR will now search at super

high speed. (in the LP/SLP modes only).

INDEX SEARCH

¡When a tape has reached the end, the VCR will

rewind the tape to the beginning, and eject the tape.

An index mark will be assigned at the beginning of

each recording you made. You may skip to a specific

marked point by following the steps below.

To stop playback, press STOP.

¡If no corresponding symbols appear on the display

when you press buttons such as PLAY, RECORD,

D or E, that means no cassette tape is in the

VCR. Please insert a tape.

Press SEARCH MODE so that the Index

Search menu appears.

Enter the number of recordings you wish to

skip by pressing K or

INDEX SEARCH

Counter Reset

within 30 seconds.

¡You can reset the counter by pressing

CLEAR/C.RESET on the remote control twice.

STILL/SLOW

Press B or { to start index search.

You can freeze the picture on TV screen by pressing

PAUSE during playback.

¡If you want to go in the forward direction, press B.

¡If you want to go in the reverse direction, press {.

¡If you want to stop search function, press STOP.

¡After index search, the VCR will play the tape auto-

matically.

¡You can advance the picture one frame at a time by

pressing PAUSE during the Still mode.

¡You cannot manually adjust the tracking of a still

picture. However, if the picture begins to vibrate

vertically during the still mode, you can stabilize the

picture by pressing CHANNEL (o/p).

TIME SEARCH

This feature allows you to go to a specific point on a

tape by entering the exact amount of time you wish to

skip in order to reach the point.

¡If the picture is distorted or rolling vertically, adjust

the vertical hold control on your TV, if so equipped.

¡You can watch in the slow motion by pressing

SLOW during playback or the still mode.

¡If a noise bar appears on the TV screen, you can

reduce it by pressing CHANNEL (o/p).

¡After the VCR has been in Still/Slow mode for 5

minutes, it will stop automatically to protect the tape

and the video head from damage.

Press SEARCH-MODE twice so that the

Time Search menu appears.

TIME SEARCH

2 : 50

Enter your desired time to

skip by pressing K or

within 30 seconds.

¡To return to playback, press PLAY.

AUTO REPEAT PLAYBACK

Press B or { to start time search.

¡If you want to go in the forward direction, press B.

¡If you want to go in the reverse direction, press {.

¡If you want to stop search function, press STOP.

¡After time search, the VCR will play the tape auto-

matically.

VCR

This feature allows you to play a tape over and over.

Select main menu by pressing MENU.

–

1L25

RECORDING FUNCTION

VCR

OTR (One Touch Recording)

You can not copy a DVD to a videotape

VCR

It may be UNLAWFUL to record copyrighted materi-

al without the consent of the copyright owner.

Accidental Erasure Prevention

This feature allows you to set the recording length sim-

ply by pressing REC/OTR on the VCR.

To prevent accidental recording on a

recorded cassette, remove its record

safety tab. To record on it later, cover the

hole with cellophane tape.

Before recording, make sure:

Press REC/OTR to begin OTR. The TIMER

REC light comes on. Change the recording

length by pressing REC/OTR repeatedly.

Record safety tab

¡The desired channel is selected by pressing Number

on the remote control or CHANNEL (o/p). (If you

connected the VCR to a cable box or satellite box as

in "CONNECTING TO A TV WITHOUT A/V TER-

MINALS" on page 13, select channel 3 on your TV,

and select the specific INPUT channel assigned by

your cable box or your satellite box on the

DVD/VCR COMBINATION UNIT. Then, select the

channel you want to record with the cable box or the

satellite box. In this case, you can ONLY record and

view the SAME channel.)

REC

OTR(0:30)

OTR(1:00).....

(Normal recording)

OTR(8:00)

OTR(7:30)

If a tape ends during OTR, the VCR will stop, eject

the tape, and switch to the DVD mode automatically

as the TIMER REC light blinks. (If the DVD power

is off, the VCR will become STANDBY status)

¡When OTR is finished , the VCR turns off automat-

ically. To use the VCR again, press T-SET on the

remote, or STOP/EJECT on the DVD/VCR COM-

BINATION UNIT.

¡If noise appears, change the RF output channel of

the VCR to channel 4 by pressing PLAY for 3 sec-

onds during playback. Then select the same chan-

nel (CH4) on your TV.

¡There is a tape with a safety tab in the VCR.

¡The desired recording speed is selected in SP (stan-

dard play) or SLP (super long play) mode by press-

ing SPEED on the remote control.

TIMER RECORDING

VCR

Tape Speed

Recording/Playback Time

Type of tape

SP mode

SLP mode

T60

1 hour

3 hours

T120

2 hours

6 hours

T160

2-2/3 hours

8 hours

You may set the VCR to start recording while you are

away. You can set eight programs to record on specif-

ic days, daily or weekly within 1 year period.

If you have not yet set the clock, "CLOCK SET"

appears. If so, follow the steps [3] and [4] in

"CLOCK SET UP" section on page 17. Then, set

the timer recording.

NORMAL RECORDING

Insert a tape with its safety tab into the

DVD/VCR COMBINATION UNIT.

VCR

Begin the recording by pressing RECORD.

The REC Light comes on.

Select main menu by pressing MENU.

TIMER PROGRAMMING

Select "TIMER PROGRAM-

MING" by pressing K or L.

Then, press B. The set up

screen is displayed.

¡To temporarily stop recording or to resume it, press

PAUSE. After the VCR has been in Pause mode for

5 minutes, it will stop automatically to protect the

tape and the video head from damage.

PROG

DATE

12345678

START TIME

END TIME

CHANNEL

REC SPEED

Set the timer.

¡To go back one step, press s.

Press STOP when the recording is completed.

Note

¡When you wish to watch another program while

recording, select desired channel on your TV. If

noise appears press VCR/TV.

¡This is not possible when using a cable box or

satellite box.

1) Set the program number (1-8)

PROGRAM NUMBER

DATE

- - / - -

START TIME - - : - - - -

END TIME - - : - - - -

CHANNEL - -

REC SPEED - -

Program number which is not set up

flashes. Press K or L repeatedly

for the desired program number.

Then, press B.

–

1L25

¡If a tape ends during TIMER RECORDING, the

VCR will stop, eject the tape, and switch to the DVD

mode automatically as the TIMER REC light blinks.

(If the DVD power is off, the VCR will become

STANDBY status).

2) Set the frequency of the recording

For once: Press K or L to point to

"ONCE".

PROGRAM NUMBER

ONCE

DAILY

WEEKLY

For daily (Monday~Friday): Press

or L to point to "DAILY".

For weekly: Press K or L to point

to "WEEKLY".

If a tape is not in the VCR or does not have a safety tab,

the TIMER REC light flashes and timer recording will

not operate. Please insert a recordable tape.

Then, press B.

When all timer recordings are finished, the TIMER

REC light will flash. To use the VCR again as usual,

press T-SET to disable the flashing TIMER REC light,

then press VCR/TV to select the VCR position. Select

either VCR or DVD mode, then continue with the

other features as described in this manual.

ONE TIME PROGRAM

PROGRAM NUMBER

DATE - - / - -

START TIME - - : - - - -

END TIME - - : - - - -

3) Set the date

First, press K or L for the month.

Then, press B. Next, press K or

L for the day. Then, press B.

CHANNEL

- -

REC SPEED - -

When timer recordings are set, the TIMER REC light

will come on. To use the VCR as usual until the time for

the recording, press T-SET so that TIMER REC light

disappears. Press VCR/TV to choose the VCR position.

Select either VCR or DVD mode, then continue with

ONE TIME PROGRAM

4) Set the start time

PROGRAM NUMBER

DATE 05 /12 MON

START TIME - - : - - - -

END TIME - - : - - - -

CHANNEL - -

REC SPEED - -

First, press K or L for the hour.

Then, press B. Next, press K or

for the minute. Then, press B. And

then, press K or L for AM or PM. Then, press B.

the other features as described in this manual

If you want to use the DVD player during

a VCR timer recording or while the

TIMER REC light is on or flashes.

You can use the DVD player while the TIMER REC

light is on or flashes, or during a timer recording.

Press POWER to turn on the DVD. Press DVD on the

remote control to choose DVD mode, then continue

with the other DVD features as described in this man-

ual. You don’t have to set the TIMER off to use the

DVD only.

ONE TIME PROGRAM

PROGRAM NUMBER

DATE 05 /12 MON

START TIME 07: 30 PM

END TIME - - : - - - -

5) Set the end time

Follow the instructions of

"Set the start time" to set

the end time.

CHANNEL

- -

REC SPEED - -

ONE TIME PROGRAM

6) Set the channel number

PROGRAM NUMBER

DATE 05 /12 MON

START TIME 07: 30 PM

END TIME 08: 30 PM

CHANNEL - -

REC SPEED - -

Press K or L repeatedly for the

desired channel number. Then,

press B.

TO STOP AN AUTOMATIC TIMER PRO-

GRAM ALREADY STARTED

Press STOP/EJECT on the DVD /VCR COMBINA-

TION UNIT.

If you connected the DVD/VCR COMBINATION UNIT to

a cable box or satellite box as in "DVD/VCR TO TV

CONNECTION" on page 13, select the DVD/VCR to channel 3

or 4 the same channel as RF output channel of the DVD/VCR.

Then, select the channel you want to record with the cable box

or satellite box.

TO CHECK, CORRECT, OR CANCEL AN

AUTOMATIC TIMER PROGRAM

Leave the cable box or satellite box on for timer recording.

ONE TIME PROGRAM

7) Set the tape speed

PROGRAM NUMBER

DATE 05 /12 MON

START TIME 07: 30 PM

END TIME 08: 30 PM

CHANNEL 16

Press T-SET.

Press K or L repeatedly for the

desired tape speed. Then, press B.

¡If the DVD output mode is selected, you have to

switch it to the VCR mode by pressing the VCR on

the remote control or the OUTPUT on the VCR.

REC SPEED SP

SLP

Select main menu by pressing MENU.

To set another program, repeat step [4]. To

exit, press CLEAR/C.RESET.

Select "TIMER PROGRAMMING" by press-

ing K or L. Then, press B.

Press T-SET to set the timer.

¡The TIMER REC light on the DVD/VCR COMBI-

NATION UNIT comes on. TIMER RECORDING

WILL NOT BE ACTIVATED UNLESS YOU

PRESS T-SET.

Select the program number you want to

check by pressing K or L.

¡The details of the selected program appears on the

TV screen.

¡Go to the digit you want to change by pressing B or

s. Then, enter correct numbers by pressing o or p.

HINTS FOR TIMER

RECORDING

¡You may cancel the entire program by pressing

while the program number flashes.

VCR

Press CLEAR/C.RESET to exit.

¡If there is a power failure or the VCR is unplugged

for more than 30 seconds, the clock setting and all

timer settings will be lost.

Press T-SET to return to timer stand-by mode

–

1L25

SPECIAL FEATURES

TO MONITOR THE RECORDING

COPYING A VIDEO TAPE

Turn on the TV and set the TV to channel 3.

VCR

¡If noise appears, change the RF output channel of

the VCR to channel 4 by pressing PLAY for 3 sec-

onds during playback. Then select the same channel

(CH4) on your TV. (See “RF OUTPUT

CHANNEL” on page 13 for the detail).

You can make copies of video tapes made by friends or

relatives for your enjoyment.

You can not copy a DVD to a videotape.

Warning:

Unauthorized recordings of copyrighted video tapes

may be an infringement of copyright laws.

Connect the recording VCR (this unit), the playing

VCR (another source) and your TV using the follow-

ing diagram.

¡You can use the AUDIO/VIDEO input jacks on the

front panel of the DVD/VCR instead of using the

jacks on the back.

Press VCR/TV on the recording VCR.

MTS (Multi-Channel Television

Sound) SYSTEM

VCR

[Recording VCR]

(this unit)

When you play a VHS tape, or receive a broadcast on

the VCR’s tuner, the current sta-

tus will appear when you press

DISPLAY on the remote control.

When you record a MTS broad-

cast signal, you need to set it to

MTS mode.

STOP

12:00AM

CH 32

STEREO

SAP

DVD/VCR

VCR

DVD

AUDIO OUT

S-VIDEO COMPONENT AUDIO

DIGITAL

AUDIO IN

1)*

2)*

OUT

VIDEO OUT OUT

AUDIO OUT

ANT-IN

COAXIAL

ANT-OUT VIDEO OUT

VIDEO IN

0:00:00

HIFI

RF cable

(supplied)

Audio/Video cables

(not supplied)

1)* Press MENU and select "TV STEREO" or

[TV set]

(Use for monitoring)

"SAP" by pressing K or L. Then, press

to select mode. To exit, press

OUT IN

CLEAR/C.RESET.

LEFT

AUDIO

RIGHT

¡Although a program may be broadcast in both stereo

and sub audio, you must select the Recording mode

to TV STEREO or SAP before you record a broad-

cast.

VIDEO

[Playing VCR]

(another source)

ANT in

Insert a pre-recorded tape into the playing VCR.

2)* Press MENU and select "AUDIO OUT" by

pressing K or L. Then, press B. Next,

select "HIFI" or "MONO" by pressing K or

L. To exit, press CLEAR/C.RESET.

Insert a tape with a safety tab into the

recording VCR.

Press SPEED on the recording VCR to select the

desired recording speed (SP/SLP)

¡While the VCR is set in HIFI stereo mode, HIFI

appears on the TV screen. While the VCR is set in

monaural (MONO) mode, HIFI disappears from the

TV screen.

Select the “L1” or “L2”position on the

recording VCR.

When you use the A/V input jacks on the back of the

DVD/VCR, select "L1" position by pressing [0], [0], [1]

on the remote control or the CHANNEL buttons (o/p).

MTS RECORDING/MONITOR MODE

Display on the

TV screen

Type of

STEREO/SAP

Selection

Hi-Fi audio track

(2-channel)

L-channel R-channel

Normal audio

track

When you use the A/V input jacks on the front of the

DVD/VCR, select "L2" position by pressing [0], [0], [2]

on the remote control or the CHANNEL buttons (o/p).

broadcast

Regular

(monaural audio)

-None-

-Invalid-

Mono

L+R

Stereo

broadcast

STEREO

SAP

-Invalid-

TV STEREO*

SAP*

Press REC/OTR on the recording VCR.

Main audio Main audio Main audio

program

Bilingual

broadcast

Begin playback of the tape in the playing

VCR.

Sub audio Sub audio

Sub audio

program

TV STEREO*

SAP*

L+R

Sub audio

program

Stereo &

Bilingual

broadcast

STEREO

SAP

¡For best results during dubbing, use the VCR’s front

panel controls whenever possible. The remote con-

trol might affect the playing VCR’s operation.

¡Always use video-quality shielded cables with

RCA-type connectors. Standard audio cables are not

recommended.

Sub audio Sub audio

program program

¡You can use a video disc player, satellite receiver, or

other audio/video component with A/V outputs in

place of the playing VCR.

–

1L25

AUTO REWIND

REAL TIME TAPE COUNTER

When a tape reaches the end during recording, play-

back, or fast-forward, the tape will automatically

rewind to the beginning. After rewinding finishes, the

VCR will eject the tape and switch itself off.

¡The VCR will not rewind the tape automatically dur-

ing timer recording or One Touch Recording.

¡This shows the elapsed recording or playback time

in hours, minutes, and seconds. (The displayed time

will not change during blank portions of the tape.)

¡The indication will appear when the tape is rewound

further than “0:00:00” on the tape counter.

PLAYING A DISC

Notes

BASIC PLAYBACK

¡A “prohibited icon” may appear at the top-right on

the TV screen during operation, warning that a pro-

hibited operation has been encountered by the DVD

or the disc.

¡With DVDs that use titles for playback program sig-

nals, playback may start from the second title, or it

may skip these titles.

¡During the playback of a two layered disc, pictures

may stop for a moment. This happens when the 1st

layer switches to the 2nd layer. This is not a mal-

function.

DVD-V

Getting started

¡Turn on the power of the TV, amplifier and any other

components which are connected to the DVD.

¡Make sure the TV and audio receiver (commercially

available) are set to the correct channel.

¡Select DVD mode by pressing DVD on the remote

control or output on the front panel.

Press POWER.

¡“Load” will appear briefly on the display panel.

GENERAL FEATURES

DVD may contain menus to navigate the disc and

access special features. Press appropriate numerical

key or use Arrow (L/K/s/B) to highlight your selec-

tion in the DVD main menu and press ENTER to con-

firm.

Press OPEN/CLOSE to open disc loading

tray.

Place the chosen disc in the tray, with the

label facing up.

Note

¡Unless stated, all operations described are based on

remote control use. Some operations can be carried

out using the menu bar on the TV screen.

PAUSE

DVD-V

Press PLAY.

¡The tray will close automatically, and playback will

then start from the first chapter or track of the disc.

If the playback does not start automatically, press

PLAY.

¡When you playback the DVD which a title menu is

recorded, it may appear on the screen. In this case,

refer to “TITLE MENU” on page 23.

During playback, press PAUSE.

¡Playback will pause and sound will be muted.

To continue playback, press PLAY.

Press STOP to stop playback.

–

1L25

DISC MENU

STEP BY STEP PLAYBACK

DVD-V

Press MENU.

¡The DVD main menu will appear.

During playback, press PAUSE.

¡Playback will pause and sound will be muted.

If the feature is not available,

may appear on the TV screen.

symbol

The disc goes forward by one frame each

time PAUSE is pressed.

If disc menu is available on the disc, audio

language, subtitle options, chapters for the

title and other options will appear for selec-

tion.

To exit step by step playback, press PLAY.

RESUME

DVD-V

Press Arrow (L/K/s/B) to select an item,

and ENTER to confirm selection.

During playback, press STOP.

¡Resume message will appear on the TV screen.

TITLE MENU

Press PLAY, playback will resume from the

point at which playback was stopped.

DVD-V

¡To cancel resume, press STOP twice.

Press TITLE.

¡The title menu will appear.

FAST FORWARD/REVERSE

If the feature is not available,

may appear on the TV screen.

symbol

DVD-V

MP3

Press Arrow (L/K/s/B) to select an item,

and ENTER to confirm selection.

During playback, press g or h repeat-

edly to select the required forward or

reverse speed: x2, x8, x50, x100 .

CALLING UP A MENU SCREEN

¡For audio CDs, the speed is fixed at ×16.

¡For MP3, the speed is fixed at ×8.

DURING PLAYBACK

¡Press MENU to call up the DVD menu.

¡Press TITLE to call up the title menu.

Note

To return to normal playback, press PLAY.

¡Contents of menus and corresponding menu opera-

tions may vary between discs. Refer to the manual

accompanying the disc for details.

SLOW FORWARD /

SLOW REVERSE

DVD-V

During playback, press PAUSE.

Press g or h .

Press g or h repeatedly to select the

required speed: 1/16, 1/8, 1/2 of the normal

playback.

To return to normal playback, press PLAY.

–

1L25

Using SKIP

ZOOM

During playback, press SKIP G to move the next

track. Press it repeatedly to skip subsequent tracks.

Press SKIP H to go back to beginning of the current

track. Press it repeatedly to go to the previous tracks.

¡Track number will appear briefly on the DVD/VCR

COMBINATION UNIT display panel.

DVD-V

The Zoom function allows you to enlarge the video

image and to pan through the enlarged image.

¡If SKIP is pressed while the playback is paused, the

playback will be paused again after skipping to the

next track.

Press ZOOM during playback.

¡Playback will continue.

Note

¡SKIP

stopped.

Press ZOOM repeatedly to select the

required zoom factor: x2, x4 or OFF.

G are not available when playback is

Use the Arrow (K/L/s / B) to move the

zoomed picture across the screen.

TITLE / CHAPTER SEARCH

Notes

To exit zoom mode, press ZOOM to OFF.

DVD-V

¡Zooming function does not work while disc menu is

shown.

¡x4 zoom is not available on some discs.

Press SEARCH MODE once for the Chapter

search, twice for the Title search during

playback.

TRACK

Enter the desired chapter/title number using

numerical buttons.

There are three ways to begin playback on an Audio

CD at a specific Track.

¡Playback will start at the selected Chapter or Title.

¡Press CLEAR to erase the incorrect input.

¡For single digits press 0 first.

Using the Numerical buttons

Press Numerical buttons to enter the

desired Track number.

TIME SEARCH

¡Playback will start at the selected track.

¡For single digit tracks (1-9), press a single number

(eg. track 3, press 3).

DVD-V

¡To play track 26, press +10, 2, 6 on the numerical

button.

Using SEARCH MODE

During playback, press SEARCH MODE

three times (CD: twice) to display the Time

Search on the TV screen.

Press SEARCH MODE.

¡The track search display appears.

Within 30 seconds, enter a desired disc

time using numerical buttons.

Within 30 seconds, select a desired track

number using numerical buttons.

¡Playback will start at the specified time.

¡For single digits press 0 first.

¡Playback will start at the selected track.

¡Press CLEAR to erase the incorrect input.

–

1L25

REPEAT

REPEAT is available only during playback.

REPEAT TITLE / CHAPTER

REPEAT A-B

DVD-V CD

DVD-V

Press REPEAT A-B at your chosen starting

point.

A- appears briefly on the TV screen.

To activate the repeat function, press REPEAT

during playback.

¡The repeat mode changes as described below every

time you press the button.

Press REPEAT A-B again at your chosen

end point.

A-B appears briefly on the TV screen, and the

CHAPTER

TITLE

OFF

repeat sequence begins.

(repeat off)

(current chapter repeat) (current title repeat)

To exit the sequence, press REPEAT A-B.

Notes

The repeat A-B section can only be set within the cur-

rent title (for DVDs), or current track (for audio CDs).

Repeat A-B is not available with some scenes in DVD.

¡Repeat Title/Chapter is not available with some

scenes.

¡The REPEAT setting will be cleared when moving

to other title or chapter.

¡To cancel the A point which was set, press CLEAR.

¡Repeat A-B playback does not function during title,

chapter, track or all repeat playback.

REPEAT TRACK

To activate the repeat function, press REPEAT

during playback.

PROGRAM

¡The repeat mode changes as described below every

time you press the button.

You may determine the order in which tracks will play.

TRACK

ALL

OFF

(repeat off)

(current track repeat)

(entire disc repeat)

In stop mode, press MODE.

¡The PROGRAM screen will appear.

Notes

¡Track Repeat setting will be cleared when moving to

other track.

¡Repeat playback does not function during repeat A-

B playback.

Press L or M to select a track, then press

ENTER.

¡Press CLEAR to erase the

most recently entered pro-

gram.

CD [AUDIO]

TOTAL 0:03:30

MP3

TRACK

GROUP

ALL

OFF

(repeat off)

(current track

(current group

(entire disc

repeat)

Notes

Press PLAY to play the programmed tracks.

¡While the program is being played back, the STOP

works as follows.

¡Press STOP once and then PLAY again, playback

will restart from the point where STOP was pressed.

(Program continued)

¡Press STOP twice and then PLAY again, playback

will restart from the track in the usual way. (Program

cleared)

¡Up to 99 programs can be entered.

¡If you like to repeat the current track in the program,

press REPEAT repeatedly until

TRACK appears

during playback. If you like to repeat the entire pro-

gram press REPEAT repeatedly until

appears during playback.

ALL

–

1L25

Notes

RANDOM PLAYBACK

¡Folders are known as Groups; files are known as

Tracks.

¡MP3 files are accompanied by

icon.

¡Maximum of 255 folders can be recognized.

¡Maximum of 256 files can be recognized.

¡Up to 8 hierarchies can be created.

This shuffles the playing order of tracks instead of

playback in the sequence.

This player recommends the use of files recorded at

the below specifications:

¡Sampling frequency: 44.1kHz or 48kHz

¡Constant bit rate: 112kbps ~ 320kbps.

In stop mode, press MODE twice.

¡RANDOM screen

RANDOM

appears.

CD [AUDIO]

TOTAL 0:45:55

RANDOM PROGRAM

--no indication--

INFORMATION

ON-SCREEN

PLAY

MP3

You can check the MP3 files during playback.

Press PLAY to start random playback.

Note

Press DISPLAY.

¡The name of the file currently in play will be dis-

¡If you like to repeat the current track in the random

selection, press REPEAT repeatedly until

TRACK appears during playback. If you like to

repeat the entire random selection press REPEAT

played.

Press DISPLAY again to show the track

number, the repeat status, and the playback

status at the top of the screen.

repeatedly until

ALL appears during playback.

MP3 PLAYBACK

will be displayed when repeat play has been

selected.

MP3

T - indicates Track repeat

When a CD with MP3 files is inserted in the

DVD/VCR, the MP3 menu will appear on the TV

screen, and number of tracks is displayed on the front

panel.

G - indicates Group (folder) repeat

A - indicates Disc repeat

Press DISPLAY again to exit.

In stop mode, press Arrow (K/L) to select

the desired group track.

TRACK SELECTION

¡If a group is selected,

press or ENTER to go

MP3

on to the track selection

screen. Press Arrow (K/L)

to choose a track, then

Press SEARCH MODE during playback.

¡The FILE LIST will appear.

press

¡If a track is selected, press

or ENTER to start playing tracks. Starting from

or ENTER.

Select a desired track using Arrow

(K/L/s/B).

¡Press B when you want to go to the next hierarchy.

¡Press s when you want to go back to the previous

hierarchy.

the one you’ve just chosen the subsequent tracks

will be played.

¡Choose FIRST PLAY to start playback from the

beginning of the listed tracks.

¡Press TITLE to return to the first item.

Press PLAY to start playing.

Notes

Press STOP to stop playback.

¡Press SEARCH MODE to exit.

¡Some selections may take a while to be recognized.

–

1L25

RANDOM PLAYBACK

SUBTITLE LANGUAGE

MP3

DVD-V

The DVD allows you to select a language for subtitles

during DVD disc (if available) playback.

Press MODE twice while playback is

stopped.

Press SUBTITLE during playback.

Press PLAY to play the tracks in random

order.

Press SUBTITLE repeatedly to select your

desired subtitle language.

PROGRAM

¡The subtitle language will be displayed on the dis-

play bar at the top of the screen.

MP3

To turn off subtitles, press SUBTITLE

repeatedly until OFF appears.

This feature allows you to program a mp3 disc to play

in a desired sequence.

Notes

¡Pressing AUDIO may not work on some DVDs with

multiple audio languages (e.g. DVDs which allow

audio language setting on the disc menu).

¡Some discs allow audio language setting/subtitle

language setting on the disc menu. (Operation varies

between discs, so refer to the manual accompanying

the disc.)

Press MODE during playback is stopped.

¡The PROGRAM screen will appear.

Press Arrow (K/L) to select a track, then

press ENTER, to save it in a program.

¡Press CLEAR to erase the incorrect input.

¡If the desired language is not shown after pressing

SUBTITLE several times, the disc does not have

subtitles in that language.

Press PLAY to start programmed playback.

¡If you choose a Language that has a 3 letter language

code, the code will be displayed every time you

change the Subtitle language setting. If you choose

any other languages, ‘---’ will be displayed instead.

(Refer to page 31.)

AUDIO LANGUAGE

DVD-V

The DVD/VCR allows you to select a language during

DVD disc (if multi language available) playback.

CAMERA ANGLE

DVD-V

Press AUDIO during playback.

Some DVD discs contain scenes which have been shot

simultaneously from various angles. You can change

Press AUDIO repeatedly to select your

desired language.

the camera angle when the (

screen.

) icon appears on the

STEREO SOUND MODE

Press ANGLE during playback.

¡The selected angle will be displayed on the display

bar at the top of the screen.

Press AUDIO repeatedly during playback to

select between STEREO, L-CH or R-CH.

Press ANGLE repeatedly to select your

desired angle.

¡STEREO - both right and left channels are active

(stereo)

L-CH - only left channel is active

R-CH - only right channel is active

Note

¡If the Virtual Surround setting is ON, the sound

mode will be fixed to STEREO, and can not be

changed.

–

1L25

CHANGING THE ON-SCREEN

DISPLAY

PARENTAL CONTROL

DVD-V

Parental Control limits the disc viewing that exceed

your settings. (with a password or playback will stop.)

This feature allows you to prevent discs with alterna-

tive scenes from being played by your children.

You can check the information about the current disc

by pressing DISPLAY on the remote control.

For DVD-Vs

PARENTAL LEVEL

Press DISPLAY during playback to show

current Chapter.

Parental Level allows you to set the rating level of

your DVD discs. Playback will stop if the disc’s rat-

ings exceed the level you set.

¡The elapsed and remaining

playing time of the current

chapter will be displayed.

9/49

0:00:00 -0:00:00

Press SETUP in STOP mode.

Press B to select CUSTOM, then press

ENTER.

Press DISPLAY again to show current Title.

¡The elapsed and remaining playing time of the cur-

rent title will be displayed.

Press Arrow (s/B) to select PARENTAL,

then press ENTER.

Press DISPLAY third time.

¡The BIT RATE and the current repeat setting will be

displayed.

PARENTAL

PARENTAL LEVEL ALL

¡If you are playing a dual layered disc, the layer num-

ber will also be displayed (L0: Layer 0 is playing.

L1: Layer 1 is playing).

Enter your four-digit password then press

ENTER.

Press DISPLAY the fourth time to remove

the display.

Press Arrow (K/L) to select PARENTAL

LEVEL, then press ENTER.

For audio CDs

Press DISPLAY during playback, the current

Track will be displayed on the TV screen.

Press Arrow (K/L) to select the desired

level.

¡The elapsed and remaining playing time of the cur-

rent track will be displayed.

Press SETUP to exit

Notes

Press DISPLAY again to show current Total

Track.

¡When doing this for the first time, enter any 4 digits.

(except for 4737) That number will be used as the

password. (in the event you forget the password, see

below.)

¡The elapsed and remaining playing time of the cur-

rent total track will be displayed.

¡To change the password, press Arrow (K/L) to

select CHANGE at step 5, then press ENTER. Enter

the four-digit pass-word, then press ENTER.

¡With some DVDs, it may be difficult to find if they

are compatible with parental lock. Be sure to check

if the parental lock function operates in the way that

you have set.

Press DISPLAY third time to remove the dis-

play.

¡Record the password in case you forget it.

IF YOU FORGET THE PASSWORD

Press 4, 7, 3, 7 at step 4. Then enter your

new password.

¡Password will be cleared and parental level will be

set to ALL.

Proceed the above Steps 5-7 again.

–

1L25

CONTROL LEVELS

Press Arrow (s /B) to select 1, 2, 3, 4, 5, 6,

7, 8, 9, or 10 and ensure that “- : - - : - -”

appears in the display.

ALL

All parental lock is cancelled.

Level 8

DVD software of any grade (adult/general/children)

can be played back.

When reaches the desired point, press

ENTER.

Levels 7 to 2

¡The Title or Track and elapsed playing time will

appear in the TV screen.

Only DVD software intended for general use and

children can be played back.

Level 1

To return to the Marker later, press SEARCH

MODE four times (CD: three times) during

playback and Arrow (s /B) to choose the

desired marker, then press ENTER.

Only DVD software intended for children can be

played back, with those intended for adult and

general use prohibited.

Notes

¡Opening the disc tray or turning off the power or

select AC at step 2 and press ENTER will erase all

Markers.

MARKER SETUP SCREEN

DVD-V

¡To clear a marker, using Arrow (s / B), position the

cursor on to the marker number to be cleared and

press CLEAR.

¡You can mark up to 10 points.

Use markers to memorise your favorite places on a

disc.

Press SEARCH MODE four times (CD: three

times) during playback.

Press SEARCH MODE or RETURN to exit.

¡The display screen and Markers will appear on the

TV screen.

DVD SETUP

DOLBY DIGITAL:

Set to On when the unit is connected to a Dolby Digital

QUICK

AUDIO SETTING

Choose the appropriate Audio settings for your equip-

ment as it only affect during the playback of DVD

discs.

Receiver.

(ON: Outputs a Dolby Digital Signal)

(OFF: Convert the Dolby Digital to PCM (2channel))

¡The default setting is ON.

DOWN SAMPLING:

¡Set to ON when outputting in 48 kHz.

¡The default setting is ON.

When playing disc with copyright Protection

¡If you select OFF, copyright protection will be acti-

vated and sound will be down sampled at 48kHz.

Press SETUP in STOP mode.

Press B to select CUSTOM, then press

ENTER.

¡CUSTOM mode will appear.

Press Arrow (s / B) to select AUDIO, then

press ENTER to confirm.

Press SETUP to exit.

AUDIO

DRC

OFF

DOLBY DIGITAL

DOWN SAMPLING ON

Press Arrow (K/L) to select the below

items, then press ENTER.

DRC (Dynamic Range Control):

¡To compress the range of soft to loud sounds.

¡The default setting is OFF.

–

1L25

BLACK LEVEL SETTING

DISPLAY SETTING

DVD-V

Adjust the Black Level Settings to make the black You can change certain aspects of the DVD display

parts of the picture as bright as you preferred. screens and on-screen messages.

Press MODE during playback.

Press SETUP in STOP mode.

Press B to select CUSTOM, then press

ENTER.

¡CUSTOM mode will appear.

Press ENTER to switch ON/OFF.

ON: Makes the dark parts brighter.

Press Arrow (s /B) to select DISPLAY, then

press ENTER to confirm.

OFF: Shows the original picture as recorded.

Press MODE twice or RETURN to exit.

DISPLAY

TV ASPECT

4:3 LETTER BOX

ANGLE ICON

AUTO POWER OFF ON

VIRTUAL SURROUND

DVD-V

MP3

Press Arrow (K/L) to select the below

items, then press ENTER.

You can enjoy stereophonic visual space on your exist-

ing stereo system.

TV ASPECT:

¡Press Arrow (K/L) for an item selection, then press

QUICK

ENTER.

Press MODE twice (CD/MP3: once) during

¡Select 4:3 LETTER BOX for a black bars appears

on top and bottom of the screen.

¡Select 4:3 PAN & SCAN for a full height picture

with both sides trimmed.

playback.

OFF

¡Select 16:9 WIDE if a wide-screen TV is connected

to the DVD/VCR.

¡The default setting is 4:3 LETTER BOX.

ANGLE ICON:

¡Press ENTER repeatedly to turn Angle icon ON or

OFF.

¡The default setting is ON.

AUTO POWER OFF:

¡Press ENTER repeatedly to turn Auto Power off ON

or OFF.

Press ENTER to set it 1 (Natural effect) or 2

(Emphasized effect) or OFF.

Press MODE or RETURN to exit.

Note (for CD play only)

¡Virtual Surround will not be effective if the sound

mode is set to something other than STEREO.

¡The default setting is ON and it will turn the

DVD/VCR to off automatically after 35 minutes of

no use.

Notes

Press SETUP to exit.

¡Be sure to press SETUP, or the setting will not work.

–

1L25

AUDIO:

¡Sets the audio language.

SUBTITLE:

¡Sets the subtitle language.

DISC MENU:

¡Sets the language for DVD menu.

LANGUAGE SETTING

DVD-V

Language options are not available with some discs.

PLAYER MENU:

¡Sets the language for the On-screen display.

QUICK

Press SETUP in STOP mode.

Press B to select CUSTOM, then press

ENTER.

Press Arrow (K/L) to select a setting, then

press ENTER.

¡CUSTOM mode will appear.

¡If OTHER is selected on the AUDIO, SUBTITLE or

DISC MENU screen, press four-digit number to

enter the code for the desired language. (Refer to the

language code list below.)

Press Arrow (s / B) to select LANGUAGE,

then press ENTER to confirm.

¡Only the languages supported by the disc can be

selected.

LANGUAGE

AUDIO

ORIGINAL

OFF

ENGLISH

Note

Press SETUP to exit.

SUBTITLE

DISC MENU

PLAYER MENU

¡Language Setting for Audio and Subtitle is not avail

able with some discs. Then use the AUDIO and the

SUBTITLE button. Details are on page 27.

Press Arrow (K/L) to select the next items,

then press ENTER.

¡If you want to return to LANGUAGE SETTING

MENU, press Arrow(s ).

Language

Code

Language

Frisian

Code

5271

5358

5747

5051

5158

5758

5360

5367

5447

5569

5455

5467

Language

Malay

Code

5965

5958

5966

5955

5964

5961

5960

6047

6051

6061

Language

Somali

Spanish [SPA]

Sundanese

Swahili

Swedish [SWE]

Code

6561

5165

6567

6569

6568

A-B

Abkhazian

Afar

Afrikaans

Albanian

Amharic

Arabic

Armenian

Assamese

Aymara

Azerbaijani

Bashkir

Basque

Bengali;Bangla

Bhutani

Bihari

Bislama

Breton

4748

4747

4752

6563

4759

4764

5471

4765

4771

4772

4847

5167

4860

5072

4854

4855

4864

4853

5971

4851

Galician

Malayalam

Maltese

Maori

Georgian

German [GER]

Greek [GRE]

Greenlandic

Guarani

Gujarati

Hausa

Hebrew

Hindi

Hungarian [HUN]

I-K

Icelandic [ICE]

Indonesian

Interlingua

Interlingue

Inupiak

Irish [IRI]

Italian [ITA]

Japanese [JPN]

Javanese

Kannada

Kashmiri

Kazakh

Kinyarwanda

Kirghiz

Kirundi

Marathi

Moldavian

Mongolian

Nauru

Tagalog

Tajik

Tamil

6658

6653

6647

6666

6651

6654

4861

6655

6661

6665

6664

6657

6669

Nepali

Norwegian [NOR]

O-R

Occitan

Tatar

Telugu

6149

6164

6159

6247

6265

5247

6258

6266

6367

6459

6461

6467

Thai

Oriya

Oromo(Afan)

Panjabi

Pashto;Pushto

Persian

Polish

Portuguese [POR]

Quechua

Rhaeto-Romance

Romanian [RUM]

Russian [RUS]

Samoan

Sangho

Sanskrit

Scots Gaelic

Serbian

Serbo-Croatian

Sesotho

Setswana

Shona

Sindhi

Tibetan

Tigrinya

Tonga

5565

5560

5547

5551

5557

5347

5566

5647

5669

5760

5765

5757

6469

5771

6460

5761

5767

Tsonga

Turkish [TUR]

Turkmen

Twi

Bulgarian

Burmese

Byelorussian

U-Z

Ukrainian

Urdu

Uzbek

6757

6764

6772

6855

6861

4971

6961

7054

5655

7161

7267

C-E

Cambodian

Catalan

5759

4947

7254

4961

5464

4965

5047

6058

5160

5161

5166

Vietnamese

Volapuk

Welsh

Wolof

Xhosa

Yiddish

Yoruba

Zulu

Chinese [CHI]

Corsican

Croatian

6559

6553

6547

5350

6564

6554

6566

6660

6560

6550

6555

6565

6557

6558

Czech

Danish [DAN]

Dutch [DUT]

English [ENG]

Esperanto

Estonian

Korean [KOR]

Kurdish

L-N

Laothian

Latin

Latvian;Lettish

Lingala

Lithuanian

Macedonian

Malagasy

5861

5847

5868

5860

5866

5957

5953

F-H

Faroese

Fiji

Finnish [FIN]

French [FRE]

5261

5256

5255

5264

Singhalese

Siswat

Slovak

Slovenian

If you choose a Language that has a 3 letter language code, the code will be displayed every time you change

the Audio or Subtitle language setting on page 27. If you choose any other languages, ‘---’ will be displayed

instead. (3 letter language code is written in bracket.)

–

1L25

TROUBLESHOOTING GUIDE

If the DVD/VCR COMBINATION UNIT does not perform properly when operated as instructed in this

Owner's Manual, check the player consulting the following checklist.

PROBLEM

No power.

CORRECTIVE ACTION

• Make sure the power plug is connected to an AC outlet.

• Make sure the power is turned on.

The player does not respond to. • Check if the power plug is connected to an AC outlet.

the remote control.

• Check the batteries in the remote control.

• Aim the remote control directly at the remote sensor. If necessary, remove all the

obstacles between the sensor and the remote.

• You have to be within 23 feet of the player.

• Check if the correct mode is selected. If not switch the mode by pressing DVD or

VCR ,whichever you need, on the remote control.

• Check if a cassette tape is in the VCR.

Timer recording is impossible. • Make sure the timer recording is set correctly.

• Make sure the power is off.

• Make sure the VCR clock is set correctly.

Cannot go into Record mode. • Make sure the tape has a safety tab. If needed, cover the hole with cellophane tape.

• Put he player in VCR mode. Press VCR on the remote control so that the green VCR

OUTPUT light is lit.

(

)

Playback picture is partially noisy • Adjust tracking control for a better picture by pressing CHANNEL

on the

DVD/VCR COMBINATION UNIT.

Cannot view a tape but the

• Head cleaning may be necessary. Refer to “AUTO HEAD CLEANING” .

• Make sure the VCR is not in the Menu mode.

audio is OK

No, or poor, playback picture.

• Change the RF output channel to CH4. Then select the same channel on the TV.

• Fine tune your TV.

TV programs cannot be seen

normally.

• Re-check the ANT. IN and ANT. OUT connections. See page 13.

• Press VCR/TV.

• Press VCR on the remote control to put it in the VCR mode. Check if the green VCR

OUTPUT light is lit. Then, set it to the TV position by pressing VCR/TV.

Video or color fades in and out

when making a copy of a video tape.

•

You cannot copy a copyrighted video tape. You are experiencing copy guard protection.

Cannot remove the tape.

• Check if the player is in the VCR mode. If not, press VCR on the remote control to switch

the mode.

No picture.

• Connect the video cables firmly.

• Insert a correct video disc that plays on this player.

• Press DVD on the remote control. Check if the DVD OUTPUT Light is lit. Then try other

DVD feature.

• Insert the disc.

• Clean the disc.

Disc cannot be played

• Place the disc correctly, with the label side up.

• Cancel the parental lock or change the control level.

• Connect the audio cables firmly.

No sound

• Turn the power of the audio component on.

• Correct the audio output settings.

• Correct the input settings on the audio component.

• This player does not support DTS audio. This is not a malfunction.

• Connect the player directly to the TV.

No DTS audio is output

Distorted picture

•

There are some cases where pictures may be slightly distorted, which are not a sign of a mal-

function.

• Although pictures may stop for a moment, this is not a malfunction.

Audio or subtitle language

does not match the set up

The camera angle cannot be

changed

•

The selected language is not available for audio or subtitles on the DVD.

This is not a malfunction

The DVD does not contain sequences recorded from different camera angles.

This is not a malfunction

•

Audio or subtitle language

cannot be changed

• The DVD does not contain audio source or subtitles in the selected language.

This is not a malfunction.

“Prohibited icon” appears on the • That operation is prohibited by the player or the disc.

screen, prohibiting an operation This is not a malfunction.

Notes

Some functions are not available in specific modes, but this is not a malfunction. Read the description in this

Owner’s Manual for details on correct operations.

¡Playback from a desired track and random playback are not available during program playback.

–

1L25

MAINTENANCE

AUTO HEAD CLEANING

SERVICING

¡Should your DVD/VCR COMBINATION UNIT ¡Automatically cleans video heads as you insert or

become inoperative, do not try to correct the prob- remove a cassette, so you can see a clear picture.

lem by yourself. There are no user-serviceable parts ¡Playback picture may become blurred or interrupted

inside. Turn off, unplug the power cord, and please

call our help line at 1-800-287-4871 to locate an

Authorized Service Center.

while the TV program reception is clear. Dirt accu-

mulated on the video heads after long periods of use,

or the usage of rental or worn tapes can cause this

problem. If a streaky or snowy picture appears dur-

ing playback, the video heads in your DVD/VCR

COMBINATION UNIT may need to be cleaned.

CLEANING THE CABINET

¡Use a soft cloth slightly moistened with a mild deter-

gent solution. Do not use a solution containing alco-

hol, spirits, ammonia or abrasive.

1. Please visit your local Audio/Video store and pur-

chase a good quality VHS Video Head Cleaner.

CLEANING DISCS

2. If a Video Head Cleaner does not solve the prob-

lem, please call our help line at 1-800-287-4871 to

locate an Authorized Service Center.

¡When a disc becomes dirty, clean it with a cleaning

cloth. Wipe the disc from the center out. Do not wipe

in a circular motion.

NOTES:

¡Do not use solvents such as benzine, thinner, com-

mercially available cleaners, detergent, abrasive

cleaning agents or antistatic spray intended for ana-

logue records.

¡Remember to read the instructions included with the

video head cleaner before use.

• Clean video heads only when problems occur.

CLEANING THE DISC LENS

¡If the player still does not perform properly when it

is operated while referring to the relevant sections

and to “TROUBLESHOOTING GUIDE” in this

Owner’s Manual, the laser optical pickup unit may

be dirty. Consult your dealer or an Authorized

Service Center for inspection and cleaning of the

laser optical pickup unit.

DISC HANDLING

¡Use discs which have the following logos on them.

(Optical audio digital discs.)

Recordable

ReWritable

¡Handle the discs so that fingerprints and dust do not

adhere to the surfaces of the discs.

¡Always store the disc in its protective case when it is

not used.

Make your contribution to the environment!!!

• Used up batteries do not belong in the dust bin.

• You can dispose of them at a collection point for used up batteries or special waste.

Contact your council for details.

–

1L25

SPECIFICATIONS

Product type:

Discs:

DVD player with Video Cassette Recorder

DVD video

Audio CD

Video Cassette tape

Converter output:

Power source:

VHF Channel 3 or 4.

120 V AC +/- 10%, 60 Hz +/- 0.5%

24 W (standby: 7.0 W)

5°C to 40°C

Power consumption:

Operating temperature:

Dimensions:

W 17-1/8” (435 mm)

H 4” (99 mm)

D 8-7/10” (218 mm)

8.16 lbs (3.7 kg)

Weight:

¡Designs and specifications are subject to change without notice.

¡If there is a discrepancy between languages, the default language will be English.

–

1L25

MEMO

–

1L25

SYLVANIA HOME ENTERTAINMENT WARRANTY

We appreciate your purchase of a SYLVANIA Home Entertainment product. We take pride in the

quality of our products and have manufactured your new Home Entertainment unit to exacting quality

standards. We feel confident that in normal use, it will provide you with satisfactory performance.

However, should you experience difficulty, you are protected under the provisions of this warranty.

SYLVANIA Home Entertainment products are warranted against manufacturing defects in materials

and workmanship in normal use for the following period from the date of purchase by the original

user, and is conditional upon the unit being installed and used as directed in the instruction manual.

PRODUCT

PARTS AND LABOUR

D.V.D. / VCR

Video Head

1 year

6 months

Remote Control 90 days

SYLVANIA's obligation under this warranty shall be limited to the repair, including all necessary parts

and the cost of the labour connected therewith, or at our option the exchange of any Home

Entertainment product which shows evidence of a manufacturing defect within the warranty period.

Replacement parts, furnished in connection with this warranty shall be warranted for a period equal to

the unexpired portion of the original equipment warranty.

CUSTOMER OBLIGATIONS

This warranty applies to the product from the original date of purchase at retail. Therefore, the owner

must provide a copy of the original, dated bill of sale. No warranty service will be performed without

a bill of sale. Transportation to and from the service depot is the responsibility of the owner.

WARRANTY EXCLUSIONS

This warranty is extended to SYLVANIA Home Entertainment products purchased and used in

Canada. This warranty shall not apply to appearance or accessory items including but not limited to:

antenna, cabinet, cabinet parts, knobs, batteries, connecting cables, cassette tapes, compact discs.

This warranty shall, in addition, not apply to damages due to handling, transportation, unpacking, set-

up, installation, customer adjustments that are covered in the instruction book, repair or replacement of

parts supplied by other than the SYLVANIA authorized service depot, any malfunction or failure

caused by or resulting from abnormal environmental conditions, improper unauthorized service,

improper maintenance, modifications or repair by the consumer, abuse, misuse, neglect, accident, fire,

flood, or other Acts of God, and incorrect line voltage.

This Home Entertainment product is only warranted to the original retail purchaser. This warranty

becomes void in the event of commercial or rental use. This warranty becomes void in the event serial

numbers are altered, defaced or removed.

SYLVANIA reserves the right to make changes in design or to make additions to or improvements

upon this product without incurring any obligation to install the same on products previously manufac-

tured. The foregoing is in lieu of all other warranties expressed or implied and SYLVANIA neither

assumes nor authorizes any person to assume for it any other obligation or liability in connection with

the sale or service of this product. In no event shall SYLVANIA or its SYLVANIA dealers be liable

for special or consequential damage arising from the use of this product, or for any delay in the perfor-

mance of this warranty due to cause beyond our control.

The purchaser may have other rights under existing provincial or federal laws, and where any terms of

this warranty are prohibited by such laws, they are deemed null and void, but the remainder of the

warranty shall remain in effect.

HOW TO OBTAIN SERVICE

Should this product require service, you may obtain specific information on how to obtain service by con-

tacting the SYLVANIA Dealer from whom this product was purchased, or by contacting us directly:

SYLVANIA SERVICE

300 Alden Road

Markham, Ontario

L3R 4C1

PHONE: (905) 940-5089 FAX: (905) 940-2303

1-800-287-4871

Printed in China

0VMN03583

####

H9404CD

Soehnle Building Set 9055 User Manual
Sony Blu ray Player 3 270 909 111 User Manual
Sony Car Speaker BDV E500W User Manual
Sony CRT Television KV EX29M87 User Manual
Sony DVD Player DVP NC66K User Manual
Sony eBook Reader PRS 950SC User Manual
Sony Two Way Radio NWZ X1051 User Manual
Speco Technologies Security Camera CVC5845DNV User Manual
Sterling Plumbing Plumbing Product E043700 User Manual
SVA Flat Panel Television VR3208W User Manual