Infra-red
Night Vision
WIRELESS
month
12
Warranty
Sees in the dark
Night Hawk™
Security Camera
with Night Vision
• 380 TV Lines for clear image resolution
How to Connect
• 12-15ft (4-5m) infra-red night vision
• 100-150ft (30-50m)* range with
Swann cameras use an AV RCA Plug
Simply connect this into your TV to
start monitoring your Swann DIY
security solution
RCA AV connector
• Weather resistant sunshield for indoors & outdoors
• Top selling home & office wireless video camera
Suggested use. Picture in Picture
?
FAQs
• What kind of image quality can I expect from the Swann Nighthawk Camera?
Enquiries: [email protected]
Wireless Surveillance
Product Code: SW231-WOC
Night Hawk™ FAQs
Can I add extra wireless cameras to my Swann Nighthawk Camera pack?
Yes, the Swann Nighthawk Camera can be set to any of 4 channels the receiver is capable of using but you will not be able
to view two wireless cameras on the same frequency or channel at the same time. Each additional camera must be set to a
different channel on your receiver.
?
Swann recommend a maximum of 3 wireless cameras for optimum reception quality but 4 cameras can be set up
successfully with careful camera placement.
Can other devices interfere with the Swann Nighthawk Camera?
?
?
Yes, some common causes of interference are Wireless LAN equipment, cordless 2.4GHz telephones and microwave ov-
ens (while they are actually cooking). Using the Swann Nighthawk Camera which has 4 switchable channels will allow you
to change to a channel that is further away from the interference source to minimize the potential for lines and noise
on your screen/recording.
How do I connect my Swann Nighthawk Camera to a TV/VCR?
The Swann Nighthawk Camera receiver comes with an AV cable which plugs into the Video ‘in’ and Audio ‘in’ connectors
on your TV or VCR. These plugs are commonly referred to as ‘RCA plugs’ and are similar to the connectors used by game
consoles and DVD players. If you plug your Swann Nighthawk Camera’s receiver into your VCR so that you can record
the footage, you will need to select the AV channel on your VCR and then the channel on your TV that you normally use
to watch video movies from your VCR. If you plug your Swann wireless receiver directly into your TV, you can view the
images on the appropriate AV channel, but you will not be able to record.
Can I use my Swann Nighthawk Camera outdoors?
?
?
The Swann Nighthawk camera has an enclosed metal case and weather resistant cap to make it suitable for outdoor
applications. Weather resistant cameras are able to be used in the outdoors if shielded from direct sun, rain, temperatures,
snow and wind. Camera power supplies must never be left exposed.
How far can I see during the day with the Swann Nighthawk Camera?
In daylight it is most useful to measure the optical range of the camera in terms of Distance to Subject (DTS). DTS is a
measurement of the ideal distance to view a subject from a camera viewing a 6ft/1.8m tall person from head to toe on a
standard television. This assumes the camera is viewing from 3ft/0.9m off the ground.
The DTS for the Swann Nighthawk Camera is 2.5m.
I have more than one wireless camera. Can I view or record these cameras simultaneously?
The Swann Nighthawk Camera receiver is only capable of displaying an image from one wireless camera at a time. To view
or record more than one camera you must set the switch at the back of the receiver to ‘Loop’. This will make the wireless
receiver automatically cycle through the 4 channels sequentially, and linger on each for about 5 seconds before repeating
the sequence.
?
What is ‘infra-red’ night vision?
?
?
Infra-red night vision allows cameras to ‘see in the dark’. It is the method of using IR LEDs (Infra-red Light Emitting Diodes)
as illumination for a camera with a sensor that can ‘see’ infra-red light. Infra-red light provides the illumination needed to
capture clear images in total darkness or low-light conditions.
How does ‘infra-red’ night vision work?
Infra-red light is a part of the light spectrum that is not visible to the human eye. When there is insufficient visible light to see
an object a Swann Nighthawk camera automatically activates its IR mode and sees the light from the IR LEDs using its IR
image sensor. The resulting image is displayed as a black & white picture on your screen.
Enquiries: [email protected]
Wireless Surveillance
Product Code: SW231-WOC
Night Hawk™ FAQs
How far can Swann Nighthawk camera see at night?
?
?
The Infra-red LEDs can project IR light that is invisible to the human eye but can be seen by the Swann Nighthawk Camera
to a distance of 16ft/5m. With a small amount of ambient light, such as street lighting and house lighting, the distance can be
extended by a small distance.
Can I connect an NightHawk System to a Swann DVR?
The NightHawk System uses RCA plugs which will not plug directly into the DVR's RCA video in sockets, but the Swann
DVRs come with an RCA to BNC adaptor to make sure that you will be able to connect the receiver directly to a Swann
DVR without having to purchase additional cables or connectors. Please note that due to the nature of wireless signals and
the potential for interference to cause false motion triggers, wireless camereras are not as well suited to operating on DVR
systems as wired cameras are.
Can I connect an NightHawk System to any TV or VCR?
?
Most TVs and VCRs made in the last 10 years have AV inputs which are what the NightHawk receiver needs to connect to.
The NightHawk System's receiver has and AV cable with RCA plugs that will connect directly to the TV or VCR's AV input.
The AV inputs are the same sockets that you connect some DVD players and Game consoles to. Once you have the Night-
Hawk System plugged in you need to select the appropriate AV channel on your TV or VCR to see the images on the TV.
There are a numbers of ways to select the AV channel and they vary from one manufacturer to the next, but some meth-
ods of selecting the AV channel with the remote are: press the AV button until the correct AV input is selected (some TVs
have 3 or more), press L1 or L2, press the Input Select button until the correct input is selected or in some cases you press
the button that is marked with a small screen that has an arrow pointing into the centre of it. Consult the manual of the TV
or VCR for more information if you are unure how to select the appropriate AV input. If you have the camera connected
to your VCR so you can record the images you will need to switch your TV to the same channel you use to watch movie
tapes on the VCR to see the images from the camera.
How long will a 9 volt battery last when used to power the Nighthawk Camera?
A 9 volt battery will last for approximately one hour depending on the quality of the battery and whether the night vision
feature is active or inactive. The battery snap adaptor is supplied to assist with the initial setup and locating of the camera
and is not intended to power the camera for sustained use.
?
Enquiries: [email protected]
Wireless Surveillance
Product Code: SW231-WOC
Night Hawk™ FAQs
Avoiding Interference!
with your Swann NightHawk Camera
From time to time cameras that use 2.4GHz transmission may experience some
interference from household devices such as cordless telephone, wireless internet
connections, microwave ovens and baby monitors. There is a solution!
Swann’s Night Hawk range of security cameras come with 4 switchable frequency
channel settings to avoid interference.
How to change the channel on your NightHawk camera
Unscrew the front of the camera case to gain access to the channel switch. To change the
frequency/channel on the receiver, press the SEL button on top of the receiver to cycle
through the channels. You can also switch the Loop/Normal switch to Loop, which
will allow the receiver to switch through all four channels automatically. The lit LED
indicates which channel is currently selected.
Front view of Switch Block (note the numbers 1 & 2 indicate the left side of the switch)
By changing these switch settings, the frequency that the camera transmits on
changes. Once you have set the channel on the camera, select the
same channel on the receiver. If you experience interference try
a different channel.
Note:
Do not set two cameras to the same channel or
they will interfere with each others signal.
Main Camera Features & Benefits
• Quality color surveillance suitable for home, office and retail security
• DIY - no cable installation required
• Professional quality images
• 11 Infra-red LEDs for night vision
• Included receiver is easily connected to a DVR, VCR, TV or PC (With Capture Card)
RS Codes:
NightHawk: 49-1059
NightHawk without Receiver: 49-1057
NightHawk Twin Pack: 49-107
Protect Property
Monitor the kids
Please note that the information
contained within this document is
subject to change without notification.
Current at March 2007.
|