1 Port RS-232/422/485 Serial over IP
Ethernet Device Server
NETRS2321E
NETRS2321EEU
NETRS2321EGB
*actual product may vary from photos
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
Manual Revision: 02/14/2012
Table of Contents
Introduction............................................................................................1
Packaging Contents ................................................................................................................................. 1
System Requirements.............................................................................................................................. 1
Top View ....................................................................................................................................................... 2
Left Side View ............................................................................................................................................. 2
Right Side View .......................................................................................................................................... 2
LED Indicators............................................................................................................................................. 3
Wiring Architecture .................................................................................................................................. 3
Installation ..............................................................................................4
Device Management Utility .................................................................................................................. 4
Web Console Configuration.................................................................................................................. 6
Controller Update ..................................................................................................................................... 10
Virtual COM Port........................................................................................................................................ 10
Factory Default Setting........................................................................................................................... 13
Self-Testing..............................................................................................14
Hyper Terminal for TCP/IP WinSock .................................................................................................... 14
Troubleshooting.....................................................................................15
Specifications..........................................................................................16
Technical Support ..................................................................................17
Warranty Information............................................................................17
Instruction Manual
i
Introduction
The NETRS2321E 1 Port RS-232/422/485 Serial over IP Ethernet Device Server is the ideal
solution for remotely controlling serial devices over your LAN/WAN or even the internet.
Featuring user-friendly browser-based configuration of network settings, serial port line
settings, UART transmit/receive buffer trigger levels and serial port flow control.
The Ethernet to RS232 converter is designed to function seamlessly with your other
integrated and add-on serial ports as if they were right inside your computer. The
adapter also offers remote Telnet configuration and support for IP, HTTP, ICMP and TCP
network protocols, while providing data transfer rates of up to 115.2Kbps per port.
Backed by a StarTech.com 2-year warranty and free lifetime technical support.
Packaging Contents
•
•
•
•
1 x NETRS2321E / GB / EU adapter
1 x Power Adapter
1 x Instruction Manual
1 x Driver CD
System Requirements
•
•
•
10/100 Mbps compatible TCP/IP Ethernet network
Available power outlet at adapter location
Virtual COM software: Microsoft® Windows® XP (32/64-bit)/Vista (32-bit)/7 (32-bit)
Instruction Manual
1
Top View
Left Side View
Right Side View
*actual product may vary from photos
Instruction Manual
2
LED Indicators
•
•
•
•
PWR (Green) - Power indicator
Data (Red) - Data sent and received indicator
10/100 (Green) - Network signal indicator.When illuminated, network connection is present.
LED (Red) - Device status indicator. When operating under normal status, this LED
will blink once per second.
Wiring Architecture
Instruction Manual
3
Installation
Device Management Utility
The Device Management Utility that is included with NETRS2321E (ETM.exe) is used to
detect and setup the installed adapter. When this tool is installed and activated, it will
detect the existence of the installed adapter, and depict its status including IP Address,
Subnet Mask, MAC Address and Device ID as shown below. The Setup Tool can only
configure one adapter at a time, therefore if there are multiple adapters installed on the
network, please ensure that they are not connected (or shut down) prior to installation.
Due to the nature of broadcast UDP packets, ETM has the following characteristics:
•
Broadcast packets are not limited by subnet. Even if the IP Address of the converters
and the computer running ETM do not belong to the same subnet, it will still
function correctly.
•
Broadcast packet signals cannot be passed through a router. ETM can only be used
to monitor devices with ETM installed, in the same segment of the LAN.
To begin using the Device Management Utility, copy the file titled ETM.exe from the
Driver CD that accompanied your NETRS2321E purchase, to your desktop. The file can
be located in the following path on the Driver CD:
E:\ETM (E: represents the CD/DVD-ROM drive)
Once the file has been copied to the desktop, connect NETRS2321E to your LAN, using
the available LAN port. Connect the included power adapter (9V DC, 500mA) to the
power port provided on NETRS2321E. Wait for a few moments for the device to be
detected, and double click on the ETM.exe icon to launch the application:
Instruction Manual
4
To refresh the status of the adapter network connection, click ‘Refresh’on the lower
right corner. This shold be performed following any configuration changes.
To configure the IP address assigned to NETRS2321E, left click on the available device,
then a window would pop up. Assign an IP Address with with the same Subnet Mask
of your computer, ensuring that the address that is assigned is not already in use on
the network. When you press the OK button, the IP Address will be refreshed within 2-3
seconds.
Instruction Manual
5
NOTE: Because the Device Management Utility uses broadcast UDP packets,
configuration is only allowed when the device’s password is left empty.
Web Console Configuration
In addition to basic IP Address and subnet mask, specific device settings can be set
using an Internet browser, such as Internet Explorer or Netscape etc.
If the IP Address of the adapter is already known (default is 192.168.0.10), enter it into
the browser address line to launch the Login Page.
The Login Page
Once the Login Page has been launched (as shown on page 6), the following will be displayed:
System time elapsed
The time elapsed since the adapter was connected to the LAN will be displayed here.
Firmware version
The installed firmware will be identified here by date code.
Serial number
The adapter serial number consists of five digits and a unique MAC address used by the
network in hexadecimal format.
Password (Setup login)
This field allows you to enter the administration password for authentication. By
default, the password is left empty. If you have changed the password to something
other than the default, press and hold the Reset button (located next to the RJ45 port)
for five seconds. The adapter will power cycle; once it has been re-detected on the
network, the password will have been reset to default. Please note that if there are
more than three consecutive incorrect password attempts, the login function will be
disabled for 15 minutes. During this period, even if the correct password is supplied,
the login will not proceed
Instruction Manual
6
The Setup Page
Once the correct password has been entered in the Setup Login password field, click
on Login to enter the Setup Page, which offers advanced configurability. The elements
that can be configured are as follows:
IP Address
Allows you to modify the assigned IP Address of the adapter. Do not enter a value that
is already in use on the connected network. If DHCP client mode is enabled, and there
is a DHCP server on the network, this field will automatically be assigned.
Subnet Mask
This field allows configuration of the subnet mask address, to which the adapter is connected.
If your subnet mask is provided by an ISP or internal network administrator, please inquire as
to what this setting is, and enter it into this field. If DHCP client mode is enabled, and there is a
DHCP server on the network, this field will automatically be assigned.
Gateway address
This field contains the gateway or router IP address. If your gateway address is
provided by an ISP or internal network administrator, please inquire as to what this
setting is, and enter it into this field. If DHCP client mode is enabled, and there is a
DHCP server on the network, this field will automatically be assigned.
Instruction Manual
7
Network link speed
This field indicates the Ethernet physical link speed. “Auto”indicates that the speed has
automatically been assigned by the NETRS2321E adapter. You can also specify 10Mbps
or 100Mbps, depending on the speed of the hub to which the adapter is connected.
DHCP client
This field will indicate either enabled or disabled status. Enable DHCP if there is a DHCP
server on your network, otherwise, leave this value as disabled.
Socket Port of HTTP Setup
The socket port used to conduct the browser setup. Normally, HTTP protocol uses TCP
port 80 for communication. If the field is changed to 81, port 80 will be reserved as an
Internet connection.
Socket port of serial I/O (RS-232/422/485):
•
Port number: A socket port assigned to the serial port. This 16-bit number ranges
from 1 to 65535. Because the numbers below 1000 are used for specific purposes
(i.e. 80 is for the http protocol), it is advisable to select a number larger than 1000.
Generally, the port number 4660 is used for serial communication. However, you
should specify a different port number for each serial port.
•
Socket type: TCP Server: TCP protocol, passive open, to be connected from TCP clients.
TCP Client: TCP protocol, active open, connect to the TCP Server.
UDP: UDP protocol, connectionless.
Destination setting:
•
Destination IP Address: The server IP Address and socket port would be connected
in TCP client and UDP client mode for a certain server IP Address.
•
Destination socket port: The server socket port would be connected in TCP Client
and UDP Client mode for a certain serial port.
•
•
Connection: The connection can be selected in two modes, Auto or Manual.
Serial I/O setting: Baud rate, parity, data bits, stop bits
Baud rate: 300 - 115200bps
Parity: None, Even, Odd
Data Bits: 7,8
Stop Bit: 1 or 2
Instruction Manual
8
•
•
Serial I/O Interface: RS-232: TxD, RxD for data stream, no flow control
RS-232 (RTS/CTS): TxD, RxD for data stream, RTS/CTS for flow control
RS-232 (RTS/CTS, DTR/DSR): TxD, RxD for data stream, RTS/CTS for flow control.
DTR for socket status, DSR for socket open/close control
RS-485 (Half duplex): Half duplex RS-485 interface
RS-422 (Full duplex): Full duplex RS-422 interface
Packet mode of serial input: Packet mode could be in enabled/disabled mode.
If packet mode is enabled, the data input from UART will be deferred until the
input buffer is full, or NETRS2321E detects a 10-character packet gap and no more
characters have arrived. The block waiting time is extended, to avoid splitting the
complete packet.
•
•
Device ID: User assigned ID number for NETRS2321E. Available ID range includes 0-65535
Report device ID when connected: In TCP mode, if this parameter is enabled, every
time the socket is connected, NETRS2321E will immediately report its device ID in
the following formats:
Serial #1 - nnnnnA[LF][CR]
Serial #2 - nnnnnB[LF][CR]
Digital I/O - nnnnnC[LF][CR]
The total length is 8 bytes, where “nnnnn”is a 5-digit device ID, assigned by the user;
[LF] is decimal 10; [CR] is decimal 13.
•
•
Setup password:Administration password used to login to the Controller Setup
page. It may be left as empty, or up to 15 characters long.
Access password: During socket connection, the Access/Authentication password
may be empty or up to entered as 15 characters long. If the Access password is left
empty, authentication is disabled. Otherwise, the authentication will proceed as
normal. If authentication fails, or no password is supplied within 10 seconds, the
socket will be closed.
Instruction Manual
9
Controller Update
Once you have entered the necessary parameters, press the Update button.
NETRS2321E will save all parameters in internal non-volatile memory and then reboot.
It will take roughly 5 or 10 seconds to complete the whole process following which a
new login page will be presented, indicating that the Controller has been updated and
that NETRS2321E is restarting.
You can re-login and check if all parameters have been correctly saved. Once you have
confirmed accuracy, you can close the browser.
NOTE: If the domain under which NETRS2321E is operating is different from that of the
computer running the browser, the login page won’t appear unless the NETRS2321E
Gateway Address has correctly been set.
Virtual COM Port
The virtual COM port software, VSerPortConsole, is used to map a NETRS2321E unit on
the network, to a COM port on the local computer system. The computer will treat the
COM port as a regular serial port that is directly on the computer system. To use the
virtual COM port feature:
1. Ensure that the NETRS2321E unit has already been configured properly, and is
accessible on the network.
2. Copy the virtual COM port software onto the computer’s hard drive from the CD, if
not already and run the software. Make sure to only run the version appropriate for
your operating system.
NOTE: The latest version of the virtual COM port software can be downloaded from
Instruction Manual
10
3. Right-click on the blank window and select the option to “Add Port”.
4. In the“Add Port”window, simply click the OK button. You choose to manually select a
COM port number or have Windows manage it. Further configuration will occur later.
5. Windows may prompt you for permission to install of the virtual serial port drivers.
6. A COM port entry should now appear in the VSerPortConsole window, and a COM
Instruction Manual
11
port should also be visible in the Windows Device Manager.
7. Right-click on the COM port in the virtual COM software and select “Add Net”.
Instruction Manual
12
8. The “Add Net”window will allow you to configure the COM port to the settings used
by the NETRS2321E unit you wish to associate with. Select the proper operating
mode, network settings used to configure the NETRS2321E unit previously (see Web
Console Configuration).
Factory Default Setting
If you forget the setup password, or have incorrect settings making the converter
inoperable, reset the settings to factory default:
You can remove power from NETRS2321E and use any point tip to push the Reset
button (next to the RJ45 port) and hold it for 5 seconds. This will automatically turn
NETRS2321E back on, and reset the password to default.
Instruction Manual
13
Self-Testing
Hyper Terminal for TCP/IP WinSock
After completing the wiring and parameter settings, it is advisable to confirm that all
settings are correct.
To use a single computer to test if NETRS2321E is performing properly:
1. Initiate a Hyper Terminal from the Start Menu in Windows. This can be done
by clicking on the Start button, selecting All Programs, then Accessories,
Communications and finally Hyper Terminal.
2. Provide a terminal name and click on OK.
3. At the “Connect to”screen that follows, select the TCP/IP(Winsock) option, and click
OK. Enter the NETRS2321E IP Address in the Host Address Field, and the Socket port
number set for Serial Port 1 in the Port number field (e.g. 4660). The Socket type of
Serial Port 1 should be TCP Server:
Instruction Manual
14
Once the necessary settings have been made, click on OK. The Hyper Terminal window
will appear - if all settings are correct, the time clock at the lower left corner of the
terminal window will indicate “connected”and the hh:mm:ss timer will begin counting.
Hyper Terminal for COM Port
Initiate another Hyper Terminal connection as a COM Port Terminal. To do so, follow
the previously listed steps (see HyperTerminal for TCP Winsock), used to create a Hyper
Terminal for TCP/IP WinSock, but instead of selecting TCP/IP (Winsock), select COM
1 (or another COM Port). Set the COM port Properties such that they are identical to
those set for the Serial port.
Data Transmission
Once the Hyper Terminals have been setup for both COM Port and TCP/IP Winsock,
type any characters in the COM Port Terminal and verify that the typed characters are
also displayed in the TCP/IP Winsock terminal. Alternatively, check if the characters
typed in the TCP/IP WinSock Terminal are also displayed in the COM Port Terminal. If
yes, then all settings are correct, and the converter can operate properly.
Troubleshooting
IftheDeviceManagementUtility(ETM.exe)doesn’tdetecttheconverteronthenetwork:
Please verify:
•
•
•
The power is properly connected to NETRS2321E
The network cable is properly connected between NETRS2321E and the hub
There is no firewall interference. If the computer you are using is Windows XP,
the Windows Firewall function may be enabled, which will block the Device
Management Utility from detecting the NETRS2321E IP Address. Therefore, you
may temporarily disable the Windows Firewall function, and re-enable it once the
necessary parameters have been configured.
If you cannot setup the NETRS2321E using Internet Explorer:
Please verify that the network domain of the PC is the same as the converter.
Instruction Manual
15
Specifications
1 x DB9 male
1 x 4-wire Terminal Block
1 x RJ45 Ethernet female
1 x DC Power
Connectors
LEDs
Power, Data, LAN Link, System
RS232/422/485
Supported Serial Protocol
Ethernet Link Speed
Maximum Data Transfer Rate
Power Adapter
10/100 Mbps
115.2 Kbps
9VDC, 500mA, type M plug
0°C ~ 60°C (32°F ~ 140°F)
-10°C ~ 70°C (14°F ~ 158°F)
0 ~ 80% RH
Operating Temperature
Storage Temperature
Humidity
Dimensions
90.0mm x 90.0mm x 26.0mm
105 g
Weight
Instruction Manual
16
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
documentation, and downloads.
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
officers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
Instruction Manual
17
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you find the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.
|