Sony Switch DVS 9000 C User Manual

^SD^WIV^TCHS^ER-^P9^RO0^CE0^SSO0^R-^PAC^CK

DVS9000SF-C

PRODUCTION SWITCHER PROCESSOR

DVS-9000

DVS-9000SF

BKDS-9160

BKDS-9470

BKDS-9161

MKS-8110SD MKS-8111SD HK-PSU04

BKDS-9162

BKDS-9210

OPERATION MANUAL [English]

1st Edition

For the customers in Europe (BKDS-9210/9160/9161/9470,

MKS-8110SD/8111SD, HK-PSU04 only)

AVERTISSEMENT

This product with the CE marking complies with the EMC

Directive (89/336/EEC) issued by the Commission of the

European Community.

Compliance with this directive implies conformity to the

following European standards:

Afin d’éviter tout risque d’incendie ou

d’électrocution, ne pas exposer cet

appareil à la pluie ou à l’humidité.

• EN55103-1: Electromagnetic Interference (Emission)

• EN55103-2: Electromagnetic Susceptibility (Immunity)

This product is intended for use in the following

Electromagnetic Environment: E4 (controlled EMC

environment, ex. TV studio).

Afin d’écarter tout risque d’électrocution,

garder le coffret fermé. Ne confier

l’entretien de l’appareil qu’à un personnel

qualifié.

Für Kunden in Europa (nur BKDS-9210/9160/9161/9470,

MKS-8110SD/8111SD, HK-PSU04)

Dieses Produkt besitzt die CE-Kennzeichnung und erfüllt die

EMV-Direktive (89/336/EEC) der EG-Kommission.

Die Erfüllung dieser Direktive bedeutet Konformität für die

folgenden Europäischen Normen:

CET APPAREIL DOIT ÊTRE RELIÉ À LA

TERRE.

• EN55103-1: Elektromagnetische Interferenz (Emission)

• EN55103-2: Elektromagnetische Empfindlichkeit

(Immunität)

Dieses Produkt ist für den Einsatz unter die folgende

elektromagnetische Bedingung ausgelegt: E4 (kontrollierter

EMV-Bereich, z.B. Fernsehstudio).

For the customers in Europe (DVS-9000/9000SF only)

This product with the CE marking complies with both the EMC

Directive (89/336/EEC) and the Low Voltage Directive (73/23/

EEC) issued by the Commission of the European Community.

Compliance with these directives implies conformity to the

following European standards:

• EN60950: Product Safety

• EN55103-1: Electromagnetic Interference (Emission)

• EN55103-2: Electromagnetic Susceptibility (Immunity)

This product is intended for use in the following

Electromagnetic Environment: E4 (controlled EMC

environment, ex. TV studio).

Pour les clients européens (BKDS-9210/9160/9161/9470,

MKS-8110SD/8111SD, HK-PSU04 uniquement)

Ce produit portant la marque CE est conforme à la Directive

sur la compatibilité électromagnétique (EMC) (89/336/CEE)

émise par la Commission de la Communauté européenne.

La conformité à cette directive implique la conformité aux

normes européennes suivantes:

• EN55103-1: Interférences électromagnétiques (émission)

• EN55103-2: Sensibilité électromagnétique (immunité)

Ce produit est prévu pour être utilisé dans l’environnement

électromagnétique suivant: E4 (environnement EMC contrôlé

ex. studio de télévision).

Für Kunden in Europa (nur DVS-9000/9000SF)

Dieses Produkt besitzt die CE-Kennzeichnung und erfüllt

sowohl die EMV-Direktive (89/336/EEC) als auch die Direktive

Niederspannung (73/23/EEC) der EG-Kommission.

Die Erfüllung dieser Direktiven bedeutet Konformität für die

folgenden Europäischen Normen:

• EN60950: Produktsicherheit

• EN55103-1: Elektromagnetische Interferenz (Emission)

• EN55103-2: Elektromagnetische Empfindlichkeit

(Immunität)

Dieses Produkt ist für den Einsatz unter die folgende

elektromagnetische Bedingung ausgelegt: E4 (kontrollierter

EMV-Bereich, z.B. Fernsehstudio).

Periodic inspections

To guarantee safe long-term operation, periodic inspections

are recommended. Please contact your Sony representative

for detailed information about the content and cost of periodic

inspections.

Pour les clients européens (DVS-9000/9000SF

uniquement)

Ce produit portant la marque CE est conforme à la fois à la

Directive sur la compatibilité électromagnétique (EMC) (89/

336/CEE) et à la Directive sur les basses tensions (73/23/

CEE) émises par la Commission de la Communauté

européenne.

La conformité à ces directives implique la conformité aux

normes européennes suivantes:

• EN60950: Sécurité des produits

• EN55103-1: Interférences électromagnétiques (émission)

• EN55103-2: Sensibilité électromagnétique (immunité)

Ce produit est prévu pour être utilisé dans l’environnement

électromagnétique suivant: E4 (environnement EMC contrôlé

ex. studio de télévision).

Table of Contents

Overview ............................................................................... 5

Features......................................................................................5

Overview of the DVS-9000 Components..................................5

Location and Function of Parts...........................................7

DVS-9000 Front Panel ............................................................. 7

DVS-9000 Rear Panel............................................................... 8

DVS-9000SF Front Pane l ....................................................... 11

DVS-9000SF Rear Pane l ........................................................ 12

Example System Configuration ........................................1 5

DVS-9000 System Configuration........................................... 15

Flow of Video Signals ............................................................ 16

Power Supply Unit Status Indicators................................ 17

Specification s ..................................................................... 18

DVS-9000 Production Switcher Processor..............................1 8

DVS-9000SF Production Switcher Processor .........................1 9

BKDS-9160 24 Output Board Set ...........................................1 9

BKDS-9161 Monitor Output Board ........................................2 0

BKDS-9162 12 Output Connector Board................................2 0

BKDS-9210 Mix/Effect Boar d ................................................2 0

BKDS-9470 DME Board Set...................................................2 0

MKS-8110SD 17 Input Boar d .................................................2 1

MKS-8111SD Additional 12 Input Board...............................2 1

HK-PSU04 Power Supply Unit ...............................................2 1

Table of Contents

Powerful frame memory functions

Up to 222 SDTV still frames can be stored in frame

memory, and up to eight frames can be called up for use

simultaneously. Frames are called up instantly, making it

possible to achieve animation effects. Image movement

and paint functions are also possible. Still pictures from

frame memory can be stored on the internal hard disk drive

of the center control panel, and still pictures can be

imported from and exported to PCs and other external

devices.

Overview

The DVS-9000-C or DVS9000SF-C Switcher Processor

Pack is a high-performance, multi-function production

switcher processor for use in an SDTV-format DVS-9000

video switcher system. It has a wide range of application,

being usable in studios and the ENG and OB vans of large-

scale live production systems as well as in postproduction

editing systems.

Four-channel DME

Features

Installation of an optional DME board set provides four-

channel DME functionality. You can apply DME wipes,

processed keys, and a wide variety of other DME

functions.

SDTV format support

This unit supports the 480i/59.94 and 576i/50 formats.

Optional backup power supply

Highly expandable system configuration

Installation of one or two optional HK-PSU04 Power

Supply Units provides backup power in addition to the

power supply unit (s) supplied as standard equipment. This

reduces the risk of power trouble and increases the

reliability of live broadcast systems.

By combining option boards, you can configure the

optimum system for your requirements, selecting the

number of inputs and outputs and the number of M/E

banks. The system’s flexibility guarantees its ability to

meet future expansion requirements.

Overview of the DVS-9000

Components

High-performance keyers

Each M/E bank is equipped with four high-performance

keyers that provide the following standard functions.

• Ability to apply transitions to keyers independently of

the background

• Chroma key and color vector keys in each keyer

• FineKey^TM, and key borders up to 8H

• Color mixable matte generator available for both key fill

and key borders

DVS-9000 Production Switcher Processor

DVS-9000 Production Switcher Processor main unit.

This is the main chassis unit of the DVS-9000 Production

Switcher Processor (size EIA 8RU).

It is supplied with boards for 2 M/E banks, 17 inputs, and

24 outputs as standard equipment.

The following options may be installed to configure

different systems.

Simultaneous output of four programs

Each M/E bank is able to handle four simultaneous

program outputs, with the ability to apply any of the four

keys to program output. This gives the system the ability

to handle a wide range of operating situations, for example

simultaneous transmission of four programs.

Option Name

Maximum number of installable option

boards

BKDS-9160

BKDS-9161

BKDS-9210

BKDS-9470

MKS-8110SD

MKS-8111SD

HK-PSU04

Powerful preview functions

The system supports simultaneous output of look-ahead

previews (next preview) and key previews, and also

transition previews.

Overview

DVS-9000SF Production Switcher

Processor

DVS-9000SF Production Switcher Processor main unit.

This is the main chassis unit of the DVS-9000SF

Production Switcher Processor (size EIA 4RU).

It is supplied with boards for 1 M/E banks, 17 inputs, and

12 outputs as standard equipment.

HK-PSU04 Power Supply Unit

A backup power supply unit. By installing one or two

backup units in the DVS-9000, or one backup unit in the

DVS-9000SF, you can back up the system’s power supply.

The following options may be installed to configure

different systems.

Option Name

Maximum number of installable option

boards

BKDS-9162

BKDS-9210

BKDS-9470

MKS-8110SD

HK-PSU04

BKDS-9160 24 Output Board Set

A 24-output board set. This option is for the DVS-9000

only. One option set can be installed.

BKDS-9161 8 Monitor Output Board

An 8-output board for monitoring input signals. This

option is for the DVS-9000 only. One option board can be

installed.

BKDS-9162 12 Output Connector Board

A 12-output connector board. This option is for the DVS-

9000SF only. One option board can be installed.

BKDS-9210 Mix Effect Board

A M/E board. Depending on the configuration, up to two

option boards can be installed in a DVS-9000 system. One

option board can be installed in a DVS-9000SF system.

BKDS-9470 DME Board Set

A 4-channel DME option board set. One option set can be

installed in either the DVS-9000 or DVS-9000SF.

MKS-8110SD 17 Input Board

A 17-input board. Up to option three boards can be

installed in the DVS-9000. One option board can be

installed in the DVS-9000SF.

MKS-8111SD Additional 12 Input Board

A 12-input expansion board. This option is for the DVS-

9000 only. One option board can be installed.

When more than 68 inputs (three MKS-8110SD boards)

are required, this board can be installed to provide up to 80

inputs.

Overview

Location and Function of Parts

DVS-9000 Front Panel

POWER

Power A, B, C, D switches and status indicator

POWER A, B, C and D switches and status indicators

The POWER switches turn the unit on and off. The unit is

powered on when the POWER switches are on the “?” side,

and powered off when the POWER switches are on the

“a” side. The status indicators light in green when the unit

is powered on.

Depending on the system’s configuration when shipped,

there may be no optional HK-PSU04 Power Supply Units

installed. In this case, the only available POWER switches

are A and B (there are no switches C and D).

The unit is not powered on until two of the POWER

switches (A, B, C, and D) are turned on.

With HK-PSU04 units installed, the system continues to

function normally as long as any two of the power supply

units are operating normally.

Caution

When installing the HK-PSU04 in your unit, be sure to

contact your Sony service representative.

Note

If a status indicator does not light when you turn a POWER

switch on, there may be a fault in the power circuits. Turn

the POWER switch off and contact your Sony service

representative.

Location and Function of Parts

DVS-9000 Rear Panel

1SWITCHER REMOTE 1 to 4 connectors

2SWITCHER CTRL connector

3 EXT connector

4REF OUT connector

5SWITCHER DATA connector

6REF IN connectors

7DME EXT IN 1 to 4 connectors

8DME DATA connector

qaDME REMOTE connector

qsDME GPI connector

9DME CTRL connector

qdSWITCHER GPI connector

0 DME MONI OUT

qfTERMINAL connector

1 to 4 connectors

EXT IN

MONI OUT

- AC IN

DATA

CTRL

REMOTE

GPI

REF IN

REMOTE

REF OUT

EXT

TERMINAL

OUT

qjOUTPUTS 1 to 48 connectors

qgU terminal

qh-AC IN A, B, C, D connectors

qkPRIMARY INPUTS 1 to 68 connectors

qlEXTEND INPUTS 69 to 80 connectors

w;MONITOR OUTPUTS 49 to 56 connectors

Location and Function of Parts

a SWITCHER REMOTE 1 to 4 connectors

(D-sub 9-pin, RS-422A)

Used to control the DVS-9000 AUX bus from external

devices, and to operate the DVS-9000 from editing control

systems such as the BVE-9100.

two connectors have a loop-through configuration.

Signal input to one connector can be output from the other

connector. If you will not be using the loop-through

output, be sure to terminate the unused connector with the

supplied 75Ω terminator.

Specify the types of connected devices on the center

control panel.

g DME EXT IN (Digital Multi Effects External

input) 1 to 4 connectors (BNC type) (BKDS-9470)

Connectors for four serial digital video signal inputs.

Dedicated input for DME external video.

b SWITCHER CTRL (Switcher Control) connector

(RJ-45)

Connect to an Ethernet switch*.

The DVS-9000 System is connected in the same way to the

Ethernet switch to form a network for exchange of signals

between the devices.

h DME DATA (Digital Multi Effects Data) connector

(RJ-45) (BKDS-9470)

Connect to an Ethernet switch.

This network is used primarily to control the various

devices from the center control panel.

The DVS-9000 System is connected in the same way to the

Ethernet switch to form a network for exchange of signals

between the devices.

* For information about Ethernet switches that can be used in an DVS-9000

system, contact your Sony service representative.

* Ethernet is a trademark of XEROX Corporation.

Caution

For more information about Ethernet switch connectors,

see “DVS-9000 System Configuration” (page 15).

When using a LAN cable: For safety, do not connect to a

connector for peripheral device wiring that might have

excessive voltage.

For detailed information about setting up the Ethernet

switch, refer to the documentation supplied with the

Ethernet switch.

i DME CTRL (Digital Multi Effects Control)

connector (RJ-45) (BKDS-9470)

Connect to an Ethernet switch.

Caution

The DVS-9000 System is connected in the same way to the

Ethernet switch to form a network for exchange of signals

between the devices.

This network is used primarily to control the various

devices from the center control panel.

When using a LAN cable: For safety, do not connect to a

connector for peripheral device wiring that might have

excessive voltage.

c EXT (extension) connector (BNC type)

Used to expand inputs by connecting devices such as an

HDS-X series routing switcher.

Caution

When using a LAN cable: For safety, do not connect to a

connector for peripheral device wiring that might have

excessive voltage.

d REF OUT (reference video output) connector

(BNC type)

Output analog sync signals.

j DME MONI OUT (Digital Multi Effects Monitor

Output) 1 to 4 connectors (BNC type) (BKDS-9470)

Connectors for four serial digital video signal outputs.

These connectors allow you to monitor any desired output

signal with the DME signal (video, key, or with graphics).

e SWITCHER DATA connector (RJ-45)

Connect to an Ethernet switch.

The DVS-9000 System is connected in the same way to the

Ethernet switch to form a network for exchange of signals

between the devices.

This network is used primarily for exchange of various

types of data (key frame effects, snapshots, etc.) and still

pictures of frame memory.

k DME REMOTE (Digital Multi Effects Remote)

connector (D-sub 9-pin, RS-422A) (BKDS-9470)

When a BKDS-9470 is installed, enables control of DME

operations from remote devices.

Caution

l DME GPI (Digital Multi Effects General Purpose

Interface) connector (D-sub 25-pin) (BKDS-9470)

Connect to external devices for input and output of trigger

signals. Up to eight inputs and eight outputs are possible,

with input and output conditions set on the center control

panel.

When using a LAN cable: For safety, do not connect to a

connector for peripheral device wiring that might have

excessive voltage.

f REF IN (reference signal input) connectors

(BNC type)

If you wish to synchronize this unit to an external reference

signal, input a black burst signal or analog sync signal. The

Location and Function of Parts

m SWITCHER GPI (Switcher General Purpose

Interface) connector (D-sub 25-pin)

t MONITOR OUTPUTS 49 to 56 connectors

(BNC type) (BKDS-9161)

Connect to external devices for input and output of trigger

signals. Up to eight inputs and eight outputs are possible,

with input and output conditions set on the center control

panel.

Use these connectors as outputs for primary input monitors

or as auxiliary outputs for external devices.

These connectors are effective if you wish to output

primary inputs with as little delay as possible.

n TERMINAL connector (D-sub 9-pin, RS-232C)

This connetor is used for factory adjustments.

o U (signal ground) terminal

Connect to the system ground.

p - AC IN (AC power input) A, B, C, D connectors

(3-pin)

Connect to 100 to 240 V AC power supply with the

optional AC power cords.

Depending on the system’s configuration when shipped,

there may be no optional HK-PSU04 Power Supply Units

installed. In that case, the AC IN C and D connectors is not

used.

Caution

For information about installing an HK-PSU04, contact

your Sony service representative.

q OUTPUTS 1 to 48 connectors (BNC type)

(BKDS-9160)

These connectors output serial digital signals. They can be

freely assigned to program output, preview output, AUX

output and so on.

There are two BNC connectors for the lower numbers on

each slot (1 to 4, 13 to 16, 25 to 28, 37 to 40) and one BNC

connector for the upper numbers (5 to 12, 17 to 24, 29 to

36, 41 to 48).

Make output assignments using the center control panel of

the DVS-9000 system.

The number of connectors varies depending on the number

of BKDS-9160 sets installed.

Refer to the User’s Guide for information about signals

that may be assigned.

r PRIMARY INPUTS 1 to 68 connectors (BNC type)

(MKS-8110SD)

These connector accept up to 68 serial digital video signal

inputs. The number of connectors varies depending on the

number of MKS-8110SD boards installed.

s EXTEND INPUTS 69 to 80 connectors (BNC type)

(MKS-8111SD)

These connectors accept up to 12 expansion serial digital

video signal inputs.

Use these connectors when 69 or more inputs are required.

Location and Function of Parts

DVS-9000SF Front Panel

POWER

Power A, B switches and status indicator

POWER

Power A, B switches and status indicators

The POWER switches turn the unit on and off. The unit is

powered on when the POWER switches are on the “?” side,

and powered off when the POWER switches are on the

“a” side. The status indicators light in green when the unit

is powered on.

Depending on the system’s configuration when shipped,

there may be no optional HK-PSU04 Power Supply Unit

installed. In this case, the only available POWER switch is

A (there is no switch B).

The unit is powered on when either of the two POWER

switches (A or B) is turned on.

With an HK-PSU04 unit installed, the system continues to

function normally as long as either of the two power

supply units is operating normally.

Caution

When installing the HK-PSU04 in your unit, be sure to

contact your Sony service representative.

Note

If a status indicator does not light when you turn a POWER

switch on, there may be a fault in the power circuits. Turn

the POWER switch off and contact your Sony service

representative.

Location and Function of Parts

DVS-9000SF Rear Panel

1EXT connector

2REF OUT connector

3SWITCHER CTRL connector

4SWITCHER DATA connector

5REF IN connectors

0DME REMOTE connector

qaDME GPI connector

6DME EXT IN 1 to 4 connectors

7DME DATA connector

qsSWITCHER GPI connector

8DME CTRL connector

qdSWITCHER REMOTE 1 to 4 connectors

9 DME MONI OUT

1 to 4

qfTERMINAL connector

connectors

EXT IN

MONI OUT

DATA

CTRL

REMOTE

GPI

REF IN

REMOTE

- AC IN

REF OUT

EXT

REMOTE

TERMINAL

OUT

- AC IN

qgU terminal

qjPRIMARY INPUTS 1 to 34 connectors

qh-AC IN A, B connectors

qkOUTPUTS 1 to 24 connectors

* For information about Ethernet switches that can be used in an DVS-9000

system, contact your Sony service representative.

a EXT (extension) connector (BNC type)

Used to expand inputs by connecting devices such as an

HDS-X series routing switcher.

For more information about Ethernet switch connectors,

see “DVS-9000 System Configuration” (page 15).

b REF OUT (reference video output) connector

(BNC type)

Output analog sync signals.

For detailed information about setting up the Ethernet

switch, refer to the documentation supplied with the

Ethernet switch.

c SWITCHER CTRL (Switcher Control) connector

(RJ-45)

Connect to an Ethernet switch*.

The DVS-9000 System is connected in the same way to the

Ethernet switch to form a network for exchange of signals

between the devices.

Caution

When using a LAN cable: For safety, do not connect to a

connector for peripheral device wiring that might have

excessive voltage.

This network is used primarily to control the various

devices from the center control panel.

Location and Function of Parts

d SWITCHER DATA connector (RJ-45)

Connect to an Ethernet switch.

i DME MONI OUT (Digital Multi Effects Monitor

Output) 1 to 4 connectors (BNC type) (BKDS-9470)

Connectors for four serial digital video signal outputs.

These connectors allow you to monitor any desired output

signal with the DME signal (video, key, or with graphics).

The DVS-9000 System is connected in the same way to the

Ethernet switch to form a network for exchange of signals

between the devices. This network is used primarily for

exchange of various types of data (key frame effects,

snapshots, etc.) and still pictures of frame memory.

j DME REMOTE (Digital Multi Effects Remote)

connector (D-sub 9-pin, RS-422A) (BKDS-9470)

When a BKDS-9470 DME Board Set is installed, use this

connector to control the unit from an external device.

Caution

When using a LAN cable: For safety, do not connect to a

connector for peripheral device wiring that might have

excessive voltage.

k DME GPI (Digital Multi Effects General Purpose

Interface) connector (D-sub 25-pin) (BKDS-9470)

Connect to external devices for input and output of trigger

signals. Up to eight inputs and eight outputs are possible,

with input and output conditions set on the center control

panel.

e REF IN (reference signal input) connectors (BNC

type)

If you wish to synchronize this unit to an external reference

signal, input a black burst signal or analog sync signal.

The two connectors have a loop-through configuration.

Signal input to one connector can be output from the other

connector. If you will not be using the loop-through

output, be sure to terminate the unused connector with the

supplied 75Ω terminator.

l SWITCHER GPI (Switcher General Puropose

Interface) connector (D-sub 25-pin)

Connect to external devices for input and output of trigger

signals. Up to eight inputs and eight outputs are possible,

with input and output conditions set on the center control

panel.

f DME EXT IN (Digital Multi Effects External

input) 1 to 4 connectors (BNC type) (BKDS-9470)

Connectors for four serial digital video signal inputs.

Dedicated input for DME external video.

m SWITCHER REMOTE 1 to 4 connectors

(D-sub 9-pin, RS-422A)

Used to control the DVS-9000SF AUX bus from external

devices, and to operate the DVS-9000SF from editing

control systems such as the BVE-9100.

Specify the types of connected devices on the center

control panel.

g DME DATA (Digital Multi Effects Data) connector

(RJ-45) (BKDS-9470)

Connect to an Ethernet switch.

The DVS-9000 System is connected in the same way to the

Ethernet switch to form a network for exchange of signals

between the devices.

n TERMINAL connector (D-sub 9-pin, RS-232C)

This connetor is used for factory adjustments.

Caution

o U (signal ground) terminal

Connect to the system ground.

When using a LAN cable: For safety, do not connect to a

connector for peripheral device wiring that might have

excessive voltage.

p -AC IN (AC power input) A, B connectors (3-pin)

Connect to 100 to 240 V AC power supply with the

optional AC power cords.

Depending on the system’s configuration when shipped,

there may be no optional HK-PSU04 Power Supply Unit

installed. In that case, the AC IN B connector is not used.

h DME CTRL (Digital Multi Effects Control)

connector (RJ-45) (BKDS-9470)

Connect to an Ethernet switch.

The DVS-9000 System is connected in the same way to the

Ethernet switch to form a network for exchange of signals

between the devices.

This network is used primarily to control the various

devices from the center control panel.

Caution

For information about installing an HK-PSU04, contact

your Sony service representative.

Caution

q PRIMARY INPUTS 1 to 34 connectors (BNC type)

(MKS-8110SD)

These connector accept up to 34 serial digital video signal

inputs. The number of connectors varies depending on the

number of MKS-8110SD boards installed.

When using a LAN cable: For safety, do not connect to a

connector for peripheral device wiring that might have

excessive voltage.

Location and Function of Parts

r OUTPUTS 1 to 24 connectors (BNC type)

(BKDS-9162)

These connectors output serial digital signals. They can be

freely assigned to program output, preview output, AUX

output and so on.

There are two BNC connectors for the lower numbers on

each slot (1 to 4, 13 to 16) and one BNC connector for the

upper numbers (5 to 12, 17 to 24) (the BKDS-9162 is

required 13 to 24).

Make output assignments using the center control panel of

the DVS-9000 system.

Refer to the User’s Guide for information about signals

that may be assigned.

Location and Function of Parts

Example System Configuration

DVS-9000 System Configuration

The figure below shows the configuration of a DVS-9000

system.

The same type of configuration is possible with a DVS-

9000SF system.

BVE-9100 Editing

Control System

Ethernet switch

DME

REMOTE

DME DME

DATA CTRL

SWITCHER

REMOTE

CTRL

SWITCHER DATA

SWITCHER CTRL

EXT IN

MONI OUT

AC IN

PERIPH

DATA

CTRL

REMOTE

GPI

REF IN

REMOTE

REF OUT

EXT

REMOTE

TERMINAL

REMOTE

Reference video

DATA

OUT

MKS-8010 System

Control Unit

signal

OUT

BKS-R Series

HDS-X Series

DVS-9000-C Switcher

Processor Pack

Reference video

signal

DCU-8000 Device Control Unit Pack

PERIPH

Reference

video signal

VTR

DDR

Audio Mixer

a) It is recommended that the

CTRL and DATA LAN networks

be configured by connecting

separate Ethernet switches for

each LAN.

b) Terminate with the supplied

75Ω terminators. Terminators

are supplied in the product

package.

Cross cable

Cable with BNC connectors

Example System Configuration

Flow of Video Signals

The figure below shows the flow of video signals in a

DVS-9000 system.

The flow of signals is the same in a DVS-9000SF system.

Camera,

VTR,routing

switcher

Monitor

Reference video signal

DME EXT IN

1 - 4

DME MONI OUT

1 - 4

Monitor

EXT IN

MONI OUT

AC IN

DATA

CTRL

REMOTE

GPI

REF IN

REMOTE

REF OUT

EXT

TERMINAL

MONITOR OUTPUTS

49 - 56

OUT

100 to 240 V AC power supply

PRIMARY INPUTS 1 - 68/

EXTEND INPUTS 69 - 80

Camera,

VTR,routing

switcher

OUTPUTS

1 - 48

OUT

DVS-9000-C Switcher Processor Pack

Monitor

VTR

a) For the AC power cord of the DVS-9000 Production Switcher Processor,

refer to “Accessories not supplied” (page 18 ).

b) Terminate with the supplied 75Ω terminators.

Terminators are supplied in the product package.

Video input signal

Video output signal

AC power supply

Example System Configuration

Power Supply Unit Status

Indicators

The power supply unit status indicators show the status of

the power supply unit during operation and when the unit

is powered on. Whenever a power error is detected, it is

reflected immediately by the indicator.

Meaning of status indicator displays

Indicator Status Description

color

Steps to take

Green

Red

Lit

Operating normally

−

Power supply unit fan Exchange the

fault

fan unit

−

Not lit

Power supply unit

fault

Exchange the

power unit

Notes

• When the unit is powered on, the status indicators may

light momentarily in red and a whining sound may be

heard. This is not a malfunction.When some of the

power supply units are off and some are on, the status

indicators of the units which are off may light in red.

This is not a malfunction.

• Power all of the installed power supply units on.

Power Supply Unit Status Indicators

Complies with RS-232C standard

Data transfer rate: 9600 bps

BNC type, 75Ω

Specifications

EXT

S-BUS data transfer rate: 312/1250 Kbps

The following specifications show the reference

performance for this unit and individual option boards/

modules.

Reference input and output

REF IN

BNC type, 75Ω, with loop-through

output

Design and specifications are subject to change without

notice.

Analog black burst/analog sync

BNC type, 75Ω

Analog sync

REF OUT

Signal level ±300 mV ±10%

Phase variation range

−90H to +90H

DVS-9000 Production Switcher

Processor

General

Video input

Power requirements

Inputs

17 (BNC type)

100 to 240 V AC, 50/60 Hz

Current consumption

100 V: 8.5 A, 240 V: 4.2A

Peak inrush current

Signal format SMPTE259M-C

Signal level 0.8 V p-p ±10%

Signal tansfer rate

270 Mbps

(1) Power ON, current probe method:

60 A (100 V), 110 A (240 V)

(2) Hot switching inrush current,

measured in accordance with

European standard EN55103-1: 40 A

(230 V)

Return loss

Cable length

15 dB

200 m (5C-2V cable, BELDEN8281 or

equivalent)

Video output

Outputs

24 (BNC type): 1 to 4 and 13 to 16, each

with 2 outputs

Operating temperature

5ºC to 40ºC (41ºF to 104ºF)

Performance guaranteed temperature

10ºC to 35ºC (50ºF to 95ºF)

Storage temperature

−20ºC to +60ºC (−4ºF to +140ºF)

Operating humidity

Signal format SMPTE259M-C

Signal level 0.8 V p-p ±10%

Signal tansfer rate

270 Mbps

10% to 90%

Dimensions (w/h/d, excluding projections)

AC input

AC IN A, B, C, D

482×354×520 mm

3-pin AC connector

(19×14×20 / inches)

Mass

Approx. 43 kg (9 lb 7 oz)

Accessories supplied

75Ω terminator (1)

Bracket (4)

Support angle (2)

Screw (+B4×10) (8)

Screw (+PSW 4×10) (8)

Operation Manual (1)

Installation Manual (1)

Control connectors

CTRL

RJ-45

Complies with 100Base-TX standard

RJ-45

Complies with 100Base-TX standard

REMOTE 1, 2, 3, 4

DATA

D-sub 9-pin, female

Comply with RS-422A standard

Data transfer rate: 38.4 Kbps

D-sub 25-pin, female

TTL inputs: 8

Relay contact outputs: 4 (30V AC/DC,

0.1A)

Accessories not supplied

AC power cord (for USA and Canada only) (125 V 10 A

2.4 m (8 ft)) (Part No.: 1-557-377-11)

AC power cord (for Europe only) (250 V 10 A 2.4 m (8 ft))

(Part No.: 1-782-929-21)

GPI

Open collector outputs: 4

D-sub 9-pin, female

TERMINAL

Specifications

Analog sync

DVS-9000SF Production Switcher

Processor

Signal level ±300 mV ±10%

Phase variation range

−90H to +90H

General

Power requirements

100 to 240 V AC, 50/60 Hz

Current consumption

100 V: 5.4 A, 240 V: 2.5 A

Peak inrush current

Video input

Inputs

Signal format SMPTE259M-C

Signal level 0.8 V p-p ±10%

Signal tansfer rate

270 Mbps

17 (BNC type)

(1) Power ON, current probe method:

60 A (100 V), 110 A (240 V)

(2) Hot switching inrush current,

measured in accordance with

European standard EN55103-1: 40 A

(230 V)

Return loss

Cable length

15 dB

200 m (5C-2V cable, BELDEN8281 or

equivalent)

Video output

Outputs

Operating temperature

12 (BNC type): 1 to 4, each with 2

outputs

5ºC to 40ºC (41ºF to 104ºF)

Performance guaranteed temperature

10ºC to 35ºC (50ºF to 95ºF)

Storage temperature

Signal format SMPTE259M-C

Signal level 0.8 V p-p ±10%

Signal tansfer rate

270 Mbps

−20ºC to +60ºC (−4ºF to +140ºF)

Operating humidity

10% to 90%

Dimensions (w/h/d, excluding projections)

AC input

482×177×520 mm

AC IN A, B

3-pin AC connector

(19×7×20 / inches)

Mass

Approx. 25 kg (5 lb 8 oz)

Accessories supplied

75Ω terminator (1)

Bracket (4)

Support angle (2)

Screw (+B4×10) (8)

Screw (+PSW 4×10) (8)

Operation Manual (1)

Installation Manual (1)

Control connectors

CTRL

RJ-45

Complies with 100Base-TX standard

RJ-45

Complies with 100Base-TX standard

REMOTE 1, 2, 3, 4

DATA

D-sub 9-pin, female

Comply with RS-422A standard

Data transfer rate: 38.4 Kbps

D-sub 25-pin, female

Accessories not supplied

AC power cord (for USA and Canada only) (125 V 10 A

2.4 m (8 ft)) (Part No.: 1-557-377-11)

GPI

TTL inputs: 8

AC power cord (for Europe only) (250 V 10 A 2.4 m (8 ft))

(Part No.: 1-782-929-21)

Relay contact outputs: 4 (30V AC/DC,

0.1A)

Open collector outputs: 4

D-sub 9-pin, female

TERMINAL

EXT

BKDS-9160 24 Output Board Set

Complies with RS-232C standard

Data transfer rate: 9600 bps

BNC type, 75Ω

General

Power requirements

12 V DC

Power consumption

Max. 50 W

Dimensions (w/h)

S-BUS data transfer rate: 312/1250 Kbps

Reference input and output

REF IN

BNC type, 75Ω, with loop-through

output

OUT board: 317×380 mm

Analog black burst/analog sync

BNC type, 75Ω

(12 / ×15 inches)

REF OUT

Specifications

CN board: 274×94 mm

Output

Outputs

(10 / ×3 / inches) (using 2 boards)

12 (BNC type), 1 to 4, each with 2 outputs

Mass

Approx. 2 kg (4 lb 6 oz)

Signal format SMPTE259M-C

Signal level 0.8 Vp-p ±10%

Signal transfer rate

270 Mbps

Output

Outputs

24 (BNC type), 1 to 4 and 13 to 16, each

with 2 outputs

Signal format SMPTE259M-C

Signal level 0.8 Vp-p ±10%

Signal transfer rate

270 Mbps

Accessories supplied

Operation and Installation Guide (1)

(supplied only when product is purchased separately)

BKDS-9210 Mix/Effect Board

Accessories supplied

Operation and Installation Guide (1)

(supplied only when product is purchased separately)

Power requirements

12 V DC

Power consumption

Max. 80 W

Dimensions (w/d, excluding projections)

BKDS-9161 Monitor Output Board

317×380 mm (12 / ×15 inches)

Mass

Approx. 2 kg (4 lb 6 oz)

General

Power requirements

12 V DC

Power consumption

Max. 10 W

Accessories supplied

Operation and Installation Guide (1)

(supplied only when product is

purchased separately)

Dimensions (w/d, excluding projections)

274×94 mm (10 / ×3 / inches)

BKDS-9470 DME Board Set

Mass

Approx. 1 kg (2 lb 3 oz)

General

Power requirements

12 V DC

Power consumption

Max. 100 W

Dimensions (w/h)

Output

Outputs

Signal format SMPTE259M-C

Signal level 0.8 Vp-p ±10%

Signal transfer rate

270 Mbps

8 (BNC type), each with 2 outputs

DVP board: 317×380 mm

(12 / ×15 inches)

Accessories supplied

Operation and Installation Guide (1)

(supplied only when product is purchased separately)

CA board: 317×380 mm

(12 / ×15 inches)

CN board: 274×94 mm

(10 / ×3 / inches) (When used with

two boards)

Approx. 4 kg (8 lb 13 oz)

BKDS-9162 12 Output Connector

Board

Mass

Remote Control connectors

CTRL

RJ-45

Complies with 100Base-TX standard

RJ-45

Complies with 100Base-TX standard

General

Power requirements

12 V DC

Power consumption

Max. 5 W

Dimensions (w/d, excluding projections)

DATA

REMOTE

D-sub 9-pin, female

Complies with RS-422A standard

Data transfer rate: 38.4 Kbps

D-sub 25-pin, female

274×94 mm (10 / ×3 / inches)

GPI

Mass

Approx. 1 kg (2 lb 3 oz)

TTL inputs: 8

Specifications

Relay contact outputs: 4 (30V AC/DC,

0.1A)

Open collector outputs: 4

MKS-8111SD Additional 12 Input

Board

Input

Inputs

General

Power requirements

12 V DC

Power consumption

Max. 10 W

Dimensions (w/h)

4 (BNC type)

Signal format SMPTE259M-C

Signal level 0.8 V p-p ±10%

Signal tansfer rate

270 Mbps

Return loss

Cable length

15 dB

274×94 mm (10 / ×3 / inches)

200 m (5C-2V cable, BELDEN8281 or

equivalent)

Mass

Approx. 1 kg (2 lb 3 oz)

Input

Inputs

Output

Outputs

12 (BNC type)

4 (BNC type)

Signal format SMPTE259M-C

Signal level 0.8 V p-p ±10%

Signal tansfer rate

270 Mbps

Signal format SMPTE259M-C

Signal level 0.8 V p-p ±10%

Signal tansfer rate

270 Mbps

Return loss

15 dB

Cable length

200 m (5C-2V cable, BELDEN8281 or

equivalent)

Accessories supplied

Operation and Installation Guide (1)

Accessories supplied

(supplied only when product is purchased separately)

Operation and Installation Guide (1)

(supplied only when product is purchased separately)

MKS-8110SD 17 Input Board

HK-PSU04 Power Supply Unit

General

Power requirements

12 V DC

Power consumption

Max. 10 W

Power requirements

100 to 240 V AC, 50/60 Hz

Power consumption

100 V: 10 A, 240 V: 5 A

Peak inrush current

Dimensions (w/h)

274×94 mm (10 / ×3 / inches)

(1) Power ON, current probe method:

60 A (100 V), 110 A (240 V)

(2) Hot switching inrush current,

measured in accordance with

European standard EN55103-1: 40 A

(230 V)

Mass

Approx. 1 kg (2 lb 3 oz)

Input

Inputs

17 (BNC type)

Signal format SMPTE259M-C

Signal level 0.8 V p-p ±10%

Signal tansfer rate

270 Mbps

Output power 12 V DC ±0.5V

Secondary power supply

Max. 60 A

Dimensions (w/h/d)

Return loss

15 dB

94×83×396 mm (3 / ×3 / ×15 / inches)

Cable length

200 m (5C-2V cable, BELDEN8281 or

equivalent)

Mass

Approx. 3 kg (6 lb 9 oz)

Accessories supplied

Operation and Installation Guide (1)

(supplied only when product is

purchased separately)

Accessories supplied

Operation and Installation Guide (1)

(supplied only when product is purchased separately)

Specifications

The material contained in this manual consists of information

that is the property of Sony Corporation and is intended solely

for use by the purchasers of the equipment described in this

manual.

Sony Corporation expressly prohibits the duplication of any

portion of this manual or the use thereof for any purpose other

than the operation or maintenance of the equipment described

in this manual without the express written permission of Sony

Corporation.

Le matériel contenu dans ce manuel consiste en informations

qui sont la propriété de Sony Corporation et sont destinées

exclusivement à l’usage des acquéreurs de l’équipement

décrit dans ce manuel.

Sony Corporation interdit formellement la copie de quelque

partie que ce soit de ce manuel ou son emploi pour tout autre

but que des opérations ou entretiens de l’équipement à moins

d’une permission écrite de Sony Corporation.

Das in dieser Anleitung enthaltene Material besteht aus

Informationen, die Eigentum der Sony Corporation sind, und

ausschließlich zum Gebrauch durch den Käufer der in dieser

Anleitung beschriebenen Ausrüstung bestimmt sind.

Die Sony Corporation untersagt ausdrücklich die

Vervielfältigung jeglicher Teile dieser Anleitung oder den

Gebrauch derselben für irgendeinen anderen Zweck als die

Bedienung oder Wartung der in dieser Anleitung

beschriebenen Ausrüstung ohne ausdrückliche schriftliche

Erlaubnis der Sony Corporation.

Sony Corporation

B & P Company

DVS-9000

(WW)

Printed in Japan

2002.07.13

3-690-433-01 (1)

Printed on recycled paper

Sennheiser Headphones Set 810 S User Manual
Sharp Fax Machine FO 2150CM User Manual
Snapper Blower ELBX10152BV User Manual
Snapper Lawn Aerator 4560 User Manual
Soleus Air Air Conditioner SG WAC 15ESE User Manual
Sony Car Stereo System XR L240 User Manual
Sony Cassette Player CFM D1 User Manual
Sony Stereo System CMT CQ1 User Manual
SOYO Computer Hardware SY P4X400 User Manual
Subaru Heat Pump 201 User Manual