3-862-214-11 (1)
Act ive
Su p e r Wo o fe r
Operating Instructions
SA-W305/W303
© 1998 by Sony Corporation
TABLE OF CONTENTS
Welcome!
Thank you for purchasing the Sony
Active Super Woofer. Before operating
this woofer, please read this manual
thoroughly and retain it for future
reference.
Getting Started
Unpacking 4
Installation 4
Hooking Up the System 5
Basic Operations
Listening to the Sound 8
Adjusting the Sound 9
Additional Information
Precautions 10
Troubleshooting 10
Specifications 11
3
Ge t t in g St a rt e d
Unpacking
Installation
Check that you received the following items:
• Audio connecting cord (1)
• Speaker cord (2)
Since the human ear cannot detect the direction and
position where the bass sound being reproduced by a
woofer (below 150 Hz) comes from, you can install the
woofer wherever you like in your room. To obtain a
better bass reproduction, we recommend you to install
the woofer on a solid floor where the resonance is
unlikely to occur.
You can obtain a sufficient heavy bass reproduction
from a single woofer. However if you use a couple of
the woofers, you can obtain an even more effective
heavy bass reproduction.
Notes
•
Always install the woofer vertically, keeping a few
centimeters from away the wall.
•
•
Do not place an object on the woofer or sit on it.
If the woofer is installed in the center of a room, the bass
could be extreamely weakened. This is due to the
influence of the standing wave of the room. If this
happened, move the woofer away from the center of a
room or eliminate the cause of the standing wave, by
installing a bookshelf on the wall, etc.
4
Ge t t in g St a rt e d
Hooking Up the System
Overview
Use the LINE IN jack or the SPEAKER IN terminals of
the woofer when you connect the amplifier.
• If your amplifier has one of the following types of
output jacks, connect the LINE IN jack and the
amplifier's jack using the supplied audio connecting
cord.
— MONO OUT jack
— MIX OUT jack
— SUB WOOFER output jack(s)
— SUPER WOOFER output jack(s)
• If your amplifier does not have the above mentioned
output jacks, connect the speaker terminals of the
amplifier to the SPEAKER IN terminals instead.
LINE IN
LINE
IN
OUT
IN
OUT
+
L
–
+
L
–
–
R
–
R
+
+
SPEAKER
SPEAKER IN
Before you get started
• Turn off the power of the amplifier and the woofer
before making any connection.
• Use the audio connecting cords that are supplied to
the respective equipment. If there are not enough
audio connecting cords to make the necessary
connections, you need to purchase some optional
audio connecting cords.
• Be sure to make connections firmly to avoid noise.
• Connect the AC power cord from the woofer to a
wall outlet.
• You cannot connect the CENTER output jack for use
with Dolby Pro Logic function to the woofer. Bass
sound is not output with some Dolby Pro Logic
modes.
(continued)
5
Ge t t in g St a rt e d
Connecting to an amplifier with a single set
of speaker terminals
Connecting to an amplifier with
double(A+B) sets of speaker terminals
If your amplifier is equipped with a single set of
speaker terminals, connect the woofer to the amplifier,
and then connect the front speakers to the woofer.
If your amplifier has double(A+B) sets of speaker
terminals, connect both the woofer and the front
speakers to the amplifier.
What cords will I need?
What cords will I need?
Speaker cord (supplied) (1 for each speaker)
Speaker cord (supplied) (1 for each speaker)
2
Twist the stripped ends of the cord about /
3
inch (15 mm).
2
Twist the stripped ends of the cord about /
3
inch (15 mm).
Be sure to match the speaker cord to the appropriate
Hookups
terminal on the componentes: + to + and – to –. If the cords
are reversed, the sound will be distorted and will lack bass.
It is useful to decide that the speaker cord marked with a
line is always the positive (+) and should be connected to the
positive (+) terminal to avoid any improper connections.
1
Connect the front speakers to the amplifier.
Connect the speakers to your amplifier’s speaker
terminals (A).
Amplifier
SPEAKER
A
Hookups
1
Connect the woofer to the amplifier.
Connect the SPEAKER IN terminals of the woofer
to the amplifier’s speaker terminals with the
speaker cords. Be sure to connect both L and R
channels.
Front
Speaker (R)
Front
Speaker (L)
ç: signal flow
Amplifier
SPEAKER
2
Connect the woofer to the amplifier.
Connect the SPEAKER IN terminals of the woofer
to the amplifier’s speaker terminals (B) using
speaker cords (supplied).
This w oofer
IN
OUT
+
L
–
+
L
–
Amplifier
SPEAKER
B
–
R
–
R
+
+
This w oofer
SPEAKER
IN
OUT
+
L
–
+
L
–
2
Connect the front speakers to the woofer.
Connect the speakers to the speaker terminals of
the woofer.
–
R
+
–
R
+
This w oofer
IN
OUT
SPEAKER
+
L
–
+
L
–
When using the double (A +B) sets of speakers, make
sure that you select the “A +B” position with your
amplifier.
Front
Speaker (R)
Front
Speaker (L)
–
R
+
–
R
+
SPEAKER
Note
When you are using speaker terminal (A) only (front speaker
only) or when the power of the amplifier is turned off, turn
down the volume or turn off the power of the woofer
otherwise, hum noise may be heard.
6
Ge t t in g St a rt e d
Connecting to an amplifier with a special
jack for a super woofer
When using this woofer for both left (L)
and right (R) channels
If your amplifier has a special jack for a super woofer
(like a MONO OUT jack, MIX OUT jack, SUB
This w oofer
This w oofer
Amplifier
LINE
LINE
MONO OUT
WOOFER jack or SUPER WOOFER jack), connect the
LINE IN jack of the woofer to one of those jacks.
IN
OUT
IN
OUT
What cords will I need?
Audio connecting cord (supplied) (1)
Connecting the AC power cord
Hookups
Connect the AC power cord from the woofer and from
your amplifier to a wall outlet.
Connect the MONO OUT jack of your amplifier to the
LINE IN jack of the woofer with the supplied audio
connecting cord.
This w oofer
Amplifier
LINE
MONO OUT
IN
OUT
Note
If the output level of your amplifier is not large enough, the
sound may not be loud enough. In this case, connect the
speaker terminals of the amplifier directly to the SPEAKER
IN terminals of the woofer.
7
Ba sic Op e ra t io n s
List e n in g t o t h e So u n d
POWER
LEVEL
CUT OFF FREQ
PHASE
MIN
MAX
50Hz
200Hz
ø
Ø
NORMAL
REVERSE
U
POWER LEVEL
Turn on the amplifier and select the program source.
1
2
Press POWER.
The woofer turns on and the POWER indicator lights up in green.
Note
Play the program source.
Never set the amplifier’s tone
control (BASS, TREBLE, etc.) or the
equalizer output to a high level or
input sinewaves of 20 Hz to 50 Hz
recorded on a commercially-
available test disc or special sound
(bass sound of electronic musical
instrument, pop noise of analog
disc turntable, sound with
abnormally enhanced bass, etc.) in
a high level to this unit. These
actions may cause damage to the
speakers.
3
Adjust the VOLUME so that sound from front speakers is not
distorted.
If it is distorted, the sound from the woofer will also be distorted.
To turn off the pow er
Press POWER to release the switch.
If you hear noise when you turn off the woofer, turn down the LEVEL of the
woofer, or turn off the amplifier before turning off the woofer.
When a special disc containing
abnormally enhanced bass is
played, noise may be output in
addition to the original sound. In
such a case, decrease the sound
level.
Note
The sub woofer output signal
(DOLBY digital (AC-3) signal) of
the digital surround processor sold
singularly is set 10 dB higher by
Dolby laboratories Licensing
Corporation. In the case of using
normally, adjust the sub woofer
level.
8
Ba sic Op e ra t io n s
Ad ju st in g t h e So u n d
You can adjust the sound of the woofer to suit the sound of your front speakers. Reinforcing the bass sound gives
you a greater sense of atmosphere.
POWER
LEVEL
CUT OFF FREQ
PHASE
MIN
MAX
50Hz
200Hz
ø
Ø
NORMAL
REVERSE
U
LEVEL CUT OFF FREQ
PHASE
Note
Adjust the cut-off frequency.
If the sound distorts when you
turn on the bass reinforcement
from your amplifier (such as,
DBFB, GROOVE, the graphic
equalizer, etc.), turn off the bass
reinforcement and adjust the
sound.
1
Turn the CUT OFF FREQ control, depending on the reproduction
frequencies of your front speakers.
80Hz
3
2
Refer to the following when adjusting.
65Hz
140Hz
1 Typical very small sized speakers: 5 – 7 cm dia.
2 Typical small sized speakers: 8 –15 cm dia.
3 Typical medium sized speakers: 16 –24 cm dia.
4
1
50Hz
200Hz
4 Typical large sized speakers: more than 25 cm dia.
To make the most of the low level converter function of Dolby digital,
turn the CUT OFF FREQ as high as possible when playing back the
Dolby digital (AC-3).
Adjust the volume level of the woofer.
2
3
Turn the LEVEL control so that you can hear the bass sound a little
more than before. Do not raise the bass excessively as this will result
in the loss of balance and depth. To increase the volume, turn the
control clockwise. To decrease the volume, turn the control
counterclockwise.
Play your favorite song and movie.
Male vocal tunes and voice containing bass sounds are most suitable
for adjustment. Turn the volume for front speakers to the same level
as usual. When playing a movie, raise the volume higher than the
level for music to produce a more powerful sound.
Note
Selecting NORMAL or REVERSE
with the PHASE button reverses
the polarity and may provide
better bass reproduction in certain
listening environments (depending
on the type of front speakers, the
position of the woofer and the
adjustment of the cut-off
Select the phase polarity.
4
5
Press the PHASE button to select the phase polarity.
Repeat steps 1 to 4 to adjust for your preference.
Once you have adjusted the woofer to the settings you desire, use the
VOLUME control on the amplifier to adjust the volume of the woofer
with that of the other speakers. You don’t need to adjust the woofer
settings when you change the volume level of the amplifier.
frequency). It may also change the
expanse and tightness of the
sound, and effect the feeling of the
sound field. Select the setting that
provides the sound you prefer
when listening in your normal
listening position.
9
Ad d it io n a l In fo rm a t io n
Precautions
Troubleshooting
If you experience any of the following difficulties while
using the woofer, use this troubleshooting guide to
help you remedy the problem. Should any problem
persist, consult your nearest Sony dealer.
On safety
• Before operating the woofer, be sure that the operating
voltage of your woofer is identical with that of your local
power supply.
• Unplug the woofer from the wall outlet if it is not to be
used for an extended period of time. To disconnect the
cord, pull the cord by grasping the plug. Never pull the
cord itself.
There’s no sound.
/Check that this woofer and components are connected
correctly and securely.
• Should any liquid or solid object fall into the woofer,
unplug the woofer and have the woofer checked by
qualified personnel before operating it any further.
• AC power cord must be changed only at the qualified
service shop.
/Turn LEVEL clockwise to turn the volume up.
/Reset the level.
The sound has suddenly stopped.
/The speaker cords may have short-circuited. Connect
the cords properly.
When turning on or off an amplifier or other equipment
Lower the volume of the amplifier to minimum.
The sound is distorted.
/The input signal is imperfect.
To avoid damaging the woofer
• Be careful in setting the volume control of the amplifier to
/The input signal level is too high.
/Set the CUT OFF FREQ as high as possible when
playing back the Dolby digital (AC-3).
avoid an excessive input power.
• Do not attempt to open the enclosuer or remold speaker
units and networks.
Severe hum or noise is heard.
• The grill net is not removable. Do not remove it.
/Connect the ground wire of the turntable properly.
/The contacts between the plugs of the connecting cords
and the corresponding jacks have not been made
properly. Connect the plugs firmly.
In case color irregularity is observed on the nearby TV
screen
With the magnetically shielded type of the speaker system,
the speakers can be installed near a TV set. However, color
irregularity may still be observed on the TV screen
depending on the type of your TV set.
/The audio system is picking up some noise from a TV
set. Move the audio system away from the TV set or
turn the TV set off.
If color irregularity is observed...
nTurn off the TV set once, then turn it on after 15 to 30
minutes.
If color irregularity is observed again...
nPlace the speakers further apart from the TV set.
When howling occurs
Relocate the speaker or turn down the volume of the
amplifier.
On installation
• Do not install the woofer near heat sources such as
radiators or air ducts, or in a place subject to direct
sunlight, excessive dust, mechanical vibration or shock.
• Good ventilation is essential to prevent internal heat
build-up in the woofer. Place the woofer in a location
with adequate air circulation. Do not place the woofer on
a soft surface or too close to a wall as this may obstruct the
ventilation hole on the back.
On cleaning the cabinet
Clean the cabinet with a soft cloth lightly moistened with
water. Do not use any type of abrasive pad, scouring
powder or solvent such as alcohol or benzine.
If you have any questions or problems concerning your
woofer that is not covered in this manual, please
consult your nearest Sony dealer.
10
Ad d it io n a l In fo rm a t io n
Specifications
Audio power specifications
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
With 6 ohms loads, from 20 – 150 Hz; rated 60 watts
(SA-W305)/ 50 watts (SA-W303) per channel minimum
RMS power, with no more than 0.8 % total harmonic
distortion from 250 milliwatts to rated output.
System
Type
Active Super Woofer (magnetically shielded
design)
Speaker unit
Woofer: 16cm dia. (63/
in.) x 1
8
Practical maximum output
SA-W305: 60 W (50 Hz)
SA-W303: 50 W (50 Hz)
Reproduction frequency range
28 – 200 Hz
High frequency cut-off frequency
50 Hz – 200 Hz
Phase selector
NORMAL, REVERSE
Inputs
Input jacks
LINE IN: Input pin jack
SPEAKER IN: Input terminals
General
Power requirements
120V, 60 Hz
Power consumption
35 W
Dimensions Approx. 205 x 380 x 365 mm (w/ h/ d)
(81/
8
x 15 x 14 3/
in.)
8
Mass
9.5 kg (20lb 15oz)
Supplied accessories
Audio connecting cord
(1 phono plug – 1 phono plug) (1)
Speaker cord (2)
Design and specifications are subject to change without
notice.
11
Sony Corporation Printed in China
|