16” Stand Fan with Remote Control
Model No: FS1-40R-33
Operating Instructions
3072986
FS1-40R-33
© 2006 Soleus Air International
WARNING: This heater is equipped with a polarized plug (one blade is wider than the other). The plug is in-
tended to fit into a power outlet only one way, with the wide blade in the wide slot. This is a safety feature; if
you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug still does not fit, contact
a qualified electrician.
DO NOT DEFEAT THE SAFETY PURPOSE OF THE POLARIZED PLUG.
TECHNICAL SPECIFICATIONS
Voltage Rating
Power Consumption
Unit Size
120V, 60Hz
55W
17.50 in. (W) x 15.75 in. (D) x 51.13 in. (H)
14 lbs
Unit Weight
3
PRODUCT DIAGRAM
4
ASSEMBLY INSTRUCTIONS
Tools required: Phillips screwdriver (not included)
Remove the fan and packaging materials from the box.
Base Assembly
1. Attach the Lower Pole (M) to the Fan Base (N) with the included Screws (P) and
Washers (O).
2. Attach the Upper Pole (I) to the Lower Pole (M) and tighten the screw located on the
bottom of the Upper Pole (I).
Fan Head Assembly
1. Unscrew (turn clockwise) the Fan Blade Cap (C) if it attached to the Motor Shaft (G).
Note: Fan Blade Cap (C) may be included in a plastic bag and not attached to the Motor
Shaft (G).
2. Unscrew (turn counter-clockwise) the Mounting Nut (E) from the Motor Shaft (G).
3. Position the Rear Grill (F) over the Motor Shaft (G), fitting the holes in the Rear Grill
(F) over the knobs that protrude from the motor. Make sure the grill fits securely against
the motor housing.
4. Screw-on (turn clockwise) the Mounting Nut (E) to secure the Rear Grill (F) to the Mo-
tor Housing (H).
5. Attach the Fan Blade (D) to the Motor Shaft (G) by aligning the slots on the Fan Blade
(D) with the bars on each side of the Motor Shaft (G).
6. Secure the Fan Blade (D) onto the Motor Shaft (G) by turning the Fan Blade Cap (C)
counter-clockwise.
7. Align the Front Grill (A) with the Rear Grill (F).
8. Place the Grill Ring (B) on the outer most edge of the Grill and secure using a Phillips
head screwdriver.
5
OPERATING INSTRUCTIONS
Using Fan Controls
1. Set the fan on a stable, level surface.
2. Turn the fan on by pressing the POWER/SPEED button located on the control panel below the Multi-Color
display, or the POWER/SPEED button on the Remote Control.
3. Adjust the speed setting by pressing the POWER/SPEED on the control panel or remote control.
4. Pressing the MODE button on either the fan or the remote will choose the desired wind mode: Standard,
Sleep, & Natural. In standard mode the fan operates at a steady speed. In Sleep mode the fan decreases
speed in the middle of the oscillation pattern. Natural mode simulates the wind by randomly alternating the
fan speed.
5. To oscillate the fan head, press the SWING button located on the fan or the remote.
6. This fan includes a 12 hour timer. To operate the timer, press the TIMER button (located on the fan &
remote) until the desired time is visible on the Multi-Colored Display. Each button press will increase the
time by 1 hour increments. Once the timer is set the words “TIMER” and “HR” will light up on the
display.
7. To turn the fan off, press the POWER/SPEED button on the fan, or the remote control until the unit turns
off.
Using the Auto-on Feature
1. First turn the fan on by pressing the POWER/SPEED button Set the fan on the fan control panel or remote
control.
2. Once the fan is on, press the AUTO button located on the remote control. Please note, the Auto-on function
is accessible by using the remote control only.
3. “AUTO” should now be displayed on the multi-color display along with the current room temperature.
When the fan is in auto mode, it will vary speeds according to the room temperature. When the room
temperature is below 68° the fan will be in standby mode (off). When the temperature is between 68° F and
74° F the fan will operate at low speed (1). When the temperature is between 75° F and 81° F the speed
will increase to medium (2). The fan will operate at high speed (3) once the room temperature is equal to or
greater than 82° F.
Adjusting Height and Fan Head Tilt
1. To adjust the height of the fan, turn the Adjustable Height Knob (L) counter-clockwise to loosen the
stand. Adjust the fan to the desired height, then firmly tighten to secure into place.
2. To adjust the tilt on the Fan Head, loosen the knob below the Motor Housing and tilt the fan
forward/back by pulling or pushing the top of the Fan Grill. The fan will make a clicking noise while
being adjusted. Once the Fan Head is set to the desired tilt, tighten the knob to secure into place.
6
CLEANING & MAINTENANCE
1. Turn the fan off and unplug the unit.
2. Wipe the fan down with a damp cloth for most efficient operation.
3. Air dry the fan completely before use.
4. Never use abrasive cleaning agents or solvents. This may cause damage or deterioration to the surface of
the unit.
5. Do not immerse the fan in any form of liquid. Do not allow water to drip on or into the fan motor
housing.
Fan Blade Cleaning:
• Make certain the fan is unplugged. Unlock the metal clips on the front grill and remove the front grill. Use
a Phillips screwdriver to loosen the securing screw and remove the fan blade.
• The fan blade and grill may be cleaned with a damp cloth and mild detergent.
• Reassemble the fan after the parts have dried completely. To do so, replace the fan blade, tighten the
securing screw, and secure the front grill. Do not plug the fan into an electrical outlet until it is fully
reassembled.
STORAGE
If the fan will not be used for a long period of time, store it in a cool, dry location when not in use. To
prevent dust and dirt build-up, use the original packaging to repack the unit.
OVERHEAT PROTECTION
A thermostat is built-in to the motor to prevent overheating. If the fan temperature exceeds the limit on the
thermostat, the fan will automatically shut-off to prevent overheating and protect the fan components from
damage.
REMOTE CONTROL
The supplied remote uses 2 “AAA” batteries. The remote will work at a distance of roughly 25 feet, and an
angle of 60°.
7
WARRANTY
One Year Limited Warranty
Soleus International Inc. warrants the accompanying Soleus Air FS1-40R-33 16” Stand Fan to be free of defects in ma-
terial and workmanship for the applications specified in its operation instruction for a period of ONE (1) year from the
date of original retail purchase in the United States.
If the unit exhibits a defect in normal use, Soleus International Inc. will, at its option, either repair or replace it, free of
charge within a reasonable time after the unit is returned during the warranty period.
As a condition to any warranty service obligation, the consumer must present this Warranty Certificate along with a
copy of the original purchase invoice.
THIS WARRANTY DOES NOT COVER:
•
Damage, accidental or otherwise, to the unit while in the possession of a consumer not caused by a defect in
material or workmanship.
•
Damage caused by consumer misuse, tampering, or failure to follow the care and special handling provisions
in the instructions. This includes dents, accidental or otherwise, to the base and head of the unit.
•
•
Damage to the finish of the case, or other appearance parts caused by wear.
Damage caused by repairs or alterations of the unit by anyone other than those authorized by Soleus
International Inc.
•
Freight and Insurance cost for the warranty service.
ALL WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANT ABILITY ARE LIMITED TO
ONE-YEAR DURATION OF THIS EXPRESS LIMITED WARRANTY. SOLEUS INTERNATIONAL INC.
DISCLAIMS ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES AND IN NO EVENT
SHALL SOLEUS INTERNATIONAL INC’S LIABILITY EXCEED THE RETAIL VALUE OF THE UNIT FOR
BREACH OF ANY WRITTEN OR IMPLIED WARRANTY WITH RESPECT TO THIS UNIT.
This warranty covers only new products purchased from our authorized dealers or retailers. It does not cover used, sal-
vaged, or refurbished products.
As some states do not allow the limitation or exclusion of incidental or consequential damages, or do not allow
limitation on implied warranties, the above limitations and exclusions may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights that vary from state to state.
For Technical Support & Warranty Service
Please Call (888) 876-5387
Or Write To:
Soleus International Inc.
9451 Telstar Ave.
El Monte, CA 91731 USA
8
|