English
ACCESS VHF SERIES USER GUIDE
This user guide provides detailed instructions for your Access VHF series wireless system. To get your system up and
running in minutes, see the Access VHF Series Quick Set Up Guide.
Your new Access VHF Series system is designed to give you both the freedom of a wireless system and world-famous
Shure sound quality. This manual covers both Single antenna and Diversity versions of the Access VHF Series systems:
the AXS31/58 handheld systems; the AXSGW bodypack systems; the AXSHW Headset systems; and the AXSLWD la-
valier microphone system.
AXS31 and AXS58
AXSGW
AXSHW
AXSLWD
Wireless
System
Bodypack system for public
speaking, theater, or busi-
ness presentations.
Hand-heldsystems for
singers.
Bodypack systems for elec-
tric and bass guitarists. Can
also be used with other elec- free operation, such as aero-
tric instruments bics or percussion
Bodypack system for ap-
plications requiring hands-
Components
Transmitter
Microphone
AXH2 Handheld
Transmitter
AXB1G Bodypack
Transmitter
AXB1 Bodypack
Transmitter
SM58 or BG3.1
––
WH20 Headset
Microphone
WL93 omnidirectional
lavalier
Receiver
AXR3 single antenna or AXR4N Diversity
PS20 (105–125 VAC, 60 Hz)
Power Supply
Supplied
Carrying and storage case; Receiver feet; Hook and loop fastening strips; gain adjustment screwdriver
Accessories
microphone stand adapter
1/4” to 1/4” guitar cables (2)
RECEIVER FEATURES
7
6
8
HERS INC.
202 USA
UNBALANCED
HIGH
Z
SQUELCH
DC INPUT
12–18 VDC
BALANCED
MIN
MAX
5
5
9
8
6
.
.
.
.
.
.
.
.
1
.
1
2
2
3
3
4
4
AXR3
AXR4N
.
7
FIGURE 1. AXR3 AND AXR4N RECEIVER FEATURES
1. Power On Indicator: Glows green when the receiver is
6. Audio Output: Provides mic level signal for connection to
amplifiers or mixing consoles. AXR3: 1/4 inch phone jack.
AXR4N: 1/4 inch phone jack and male XLR connector.
powered on.
2. RF Signal Indicator: AXR3: Glows yellow when RF (radio
frequency) signals are received. AXR4N: One of two indica-
tor lights glows when RF is received by antenna A or B.
7. Squelch Control: This control is factory pre-set and nor-
mally requires no adjustment. See Wireless System Adjust-
ments at the end of this guide.
3. Audio Peak Indicator: Flashes red when the audio signal
received approaches overload clipping level.
4. Volume Control: Adjusts the output volume of the receiver.
8. Power Input: Accepts power from supplied AC adapter.
Does not affect Transmitter Audio Peak indicator.
5. Telescoping Antenna(s): Receives signals from the trans-
9. Power Cable Retainer: AXR4N only. Secures the AC
mitter.
adapter cable to the receiver.
1
English
SYSTEM SETUP
BATTERY INSTALLATION
BODYPACK TRANSMITTER SETUP
1. Attach the transmitter to your belt, guitar strap, or waistband
as shown in Figure 6. Depress the tab marked PRESS and
slip the belt or strap between the transmitter body and the
belt clip. For added stability, draw the strap or belt toward the
clip’s top wire, especially when using thin guitar straps.
1. Slide the transmitter POWER ON/OFF switch to the OFF
position.
2. AXB1, AXB1G: Press down on the OPEN side of the battery
compartment cover, slide it back and flip it open, as shown
in Figure 4.
AXH2: Unscrew the transmitter battery cover to expose the
battery terminals, as shown in Figure 3.
AXB1/AXB1G
-
+
FIGURE 6. TRANSMITTER SETUP
2. Plug your guitar, headset microphone, or lavalier micro-
phone into the transmitter.
FIGURE 4. BATTERY INSTALLATION
3. Insert a fresh 9V alkaline battery into the battery compart-
ment (A Duracell MN1604 is recommended). A fresh 9V alka-
line battery will typically provide 18 hours of performance
time. A fully charged 8.4V NiCad battery will provide about
2 hours of performance time.
RECEIVER SETUP
1. Plug one end of the AC power adapter into the DC INPUT con-
nector on the back of the receiver. AXR4N: Loop the power
cable around the cable retainer on the bottom of the receiver.
See Figure 7. Plug the other end into an AC power source (use
PS20 for 105–125 VAC. The green POWER light on the re-
ceiver will glow.
IMPORTANT: Carbon-zinc and zinc-chloride batteries will
not provide adequate power and are not recommended.
4. Replace the battery cover.
HEADSET ASSEMBLY
1. Refer to the tag attached to the headset for assembly in-
structions. After assembling the WH20, adjust the head-
band and place it on your head.
2. Position the microphone over the corner of your mouth,
about 1/2 inch away. See Figure 5.
1
2
FIGURE 7. AXR4N POWER CABLE RETAINER
3. To reduce pops and breath noise, place the supplied foam
windscreen over the microphone.
2. Connect the receiver output. The Guitarist: plug a standard
guitar cable (two provided) into the receiver’s output con-
nector. Plug the other end into a guitar amplifier, as shown
in Figure 8. AXSHW, AXS31, AXS58 or AXSLWD: Use a
cable with a 1/4 inch phone plug (AXR3, AXR4N) or a fe-
male XLR connector (AXR4N) to connect the receiver to a
mic level input of a mixer or PA system, as shown in Figure
8.
3. Extend antenna(s). AXR3: The antenna should be fully ex-
tended and vertical, as shown in Figure 8. AXR4N: The an-
tennas should be fully extended and angled away from each
other, at an angle of 45 degrees from vertical, as shown in
Figure 8.
FIGURE 5. HEADSET MICROPHONE POSITION
3
English
WIRELESS SYSTEM OPERATION
T1G
AXR3
AXR4N
45°
45°
SHURE
AXR3
SHURE
AXR4N
45°
45°
SHURE
FIGURE 8. WIRELESS SYSTEM OPERATION
ESTABLISHING A WIRELESS LINK
OPERATING YOUR WIRELESS SYSTEM
When powered on, your transmitter broadcasts an RF carrier
signal. When picked up by your receiver, this signal links your
wireless system together and allows wireless transfer of audio
signals from your microphone or instrument. The RF signal is
broadcast steadily, even when your transmitter is muted. The
yellow RF light (AXR3) and ANTENNA A/B lights (AXR4N) indi-
cate when this link is established.
To test your wireless link, setup your transmitter and receiver as
described above. Turn on your transmitter while remaining
close enough to the receiver to see the yellow RF or ANTENNA
lights. The RF light (AXR3) or one of the ANTENNA lights
1. Once you have established a wireless link, slide the trans-
mitter MUTE switch to the ON position.
2. Sing, speak, or play your instrument at typical volume lev-
els. (AXSGW systems: turn the volume control on your gui-
tar or bass all the way up.) Normal operation is indicated by:
• Steady glow of yellow RF light (AXR3) or ANTENNA light A
or B (AXR4N).
• Flickering of the red PEAK light (AXR3) or TRANSMITTER
AUDIO PEAK light (AXR4N) when loud sounds are trans-
mitted.
(A•XRIf4tNh)esRhoFuoldr iAlluNmTiEnNatNe.A lights do not illuminate, see the
NOTE: If the red TRANSMITTER AUDIO PEAK light on the
receiver does not flicker occasionally, refer to the Wireless
System Adjustments Section below.
Troubleshooting section in this guide.
Turn your transmitter off. The RF or ANTENNA light should go
ou•t. If the RF or ANTENNA lights do not go out after you turn off
your transmitter, your receiver is picking up an RF signal
from some other source. If you cannot identify and remove
this source (usually other digital or wireless electronic
equipment nearby), place your receiver in another loca-
tion. If external RF sources cannot be avoided, you may
need a wireless system that operates on a different carrier
frequency. Contact your Shure dealer.
3. When finished, slide the MUTE switch to MUTE. Then slide
the transmitter POWER switch to OFF. (Muting the transmit-
ter first will help prevent audio thumps that may occur when
powering off the transmitter.)
4
English
WIRELESS SYSTEM ADJUSTMENTS
TRANSMITTER AUDIO GAIN ADJUSTMENT
RECEIVER VOLUME ADJUSTMENT
AXSGW Systems: The audio gain control on the transmitter in
these systems is factory-preset at the minimum setting (full
counterclockwise) to reduce the risk of overload and distortion.
If the red TRANSMITTER AUDIO PEAK light on the receiver
does not flicker when the guitar is played loudly and its volume
controls are turned all the way up, increase the transmitter gain
level. This will ensure the best signal-to-noise ratio for perfor-
mance. See Figure 9.
The volume control on the front panel of the AXR3 and AXR4N
receivers can be adjusted to make the wireless system output
level identical to that of a cabled guitar or bass or wired micro-
phone. After making any necessary transmitter gain adjust-
ments, adjust the receiver volume control until the output reach-
es the desired level. Rotate the volume control clockwise to
increase output. Rotate it counterclockwise to decrease output.
AXSHW Systems: The audio gain control on the transmitter in
the headset systems is factory preset at the maximum setting
(full clockwise). This is because the microphone in the WH20 is
a low output, dynamic microphone. It may be necessary to re-
duce the transmitter gain until the red TRANSMITTER AUDIO
PEAK light flickers only when you speak or sing loudly. This will
ensure the best signal to noise ratio for performance. See Fig-
ure 9.
RECEIVER SQUELCH ADJUSTMENT
The squelch control on the AXR3 and AXR4N receivers is
factory preset for optimum performance. No further adjust-
ment is normally required. It is possible to adjust the squelch
control setting to emphasize either signal quality or system
range:
• Turning the squelch control clockwise causes the receiver
to demand a higher quality signal (less noise before mut-
ing), but decreases operating range.
AXS31/AXS58/AXSLWD: The audio gain controls on the trans-
mitters in these systems have been factory preset at the mid-
range position. This will provide the best results in most applica-
tions. However, for singers or presenters with quiet voices, the
audio gain may need to be increased for better signal-to-noise ra-
tio. Increase the gain until the receiver’s TRANSMITTER AUDIO
PEAK light flickers when you speak in a loud voice. For those with
loud voices, the preset gain level may be too high, causing un-
wanted distortion. In this case, the PEAK indicator will glow con-
tinuously when you sing or speak in a loud voice and the gain
level should be reduced. See Figure 9.
• Turning the squelch control counterclockwise allows a low-
er quality signal through (more noise before muting), but in-
creases operating range.
To return the receiver squelch control to the factory setting, ro-
tate it to the mid-range position (so the slot is vertical).
ABOUT THE SHURE NOISE SQUELCH SYSTEM
Conventional squelch circuits analyze RF signal strength. Conse-
quently, they cannot discriminate between noise and desired sig-
nals. When a wireless system is used in a noisy RF environment,
conventional circuits may “open” unexpectedly, sending loud
bursts of noise through the receiver when the transmitter’s signal is
weak or turned off. Unlike conventional wireless systems, Shure
T-Series systems use a noise squelch circuit that analyzes signal
quality instead of signal strength. A special detector monitors the
level of high frequency noise. When the transmitter signal is
strong, the system’s noise level is low and the receiver sends au-
dio through. When the transmitter signal is weak or absent, the
system’s noise level is high and the squelch circuit will mute the
receiver. This virtually eliminates the possibility of annoying bursts
of noise coming through your receiver.
AXB1/AXB1G
+
9 V
AXH2
-
FIGURE 9. GAIN ADJUSTMENT
• To Increase Gain: Rotate the transmitter gain control clock-
wise with the supplied screwdriver until the red TRANS-
MITTER AUDIO PEAK light on the receiver flickers when
the guitar is played loudly, or when you sing or speak in a
loud voice.
TIPS FOR ACHIEVING MAXIMUM PERFORMANCE
• Make sure you can always see a receiver antenna from the
transmitter position.
• To Reduce Gain: Rotate the transmitter gain control counter-
clockwise until the red TRANSMITTER AUDIO PEAK light
on the receiver flickers only when the guitar is played
loudly, or when you speak or sing in a loud voice.
• Keep the distance between the transmitter and the receiv-
er antennas short.
• Avoid placing the receiver antennas near metal surfaces
• To Return Audio Gain to the Factory Setting: Rotate the
transmitter audio gain control counterclockwise as far as it
will go (AXSGW systems), clockwise as far as it will go
(AXSHW systems), or to mid position (AXS31, AXS58 and
AXSLWD Systems).
and obstructions. They will reduce system performance.
• To mount the receiver on a flat surface, attach the four
adhesive rubber feet or secure the receiver to the surface
with the supplied cloth fastening strips.
5
English
TROUBLESHOOTING
INDICATOR STATUS
= on = flickers on loud peaks
PROBLEM
SOLUTIONS
AXR4N RECEIVER
AXR3 RECEIVER
TRANS-
MITTER
TRANSMITTER
AUDIO
ANTENNA
POWER
POWER
• Slide transmitter POWER switch to ON.
• Make sure battery is inserted properly (+/– battery terminals must
A
ON
B
PEAK
PEAK
match transmitter terminals).
LOW BATT
RF
POWER
• Insert fresh battery.
TRANSMITTER
AUDIO
ANTENNA
POWER
POWER
• Make sure AC adapter is securely plugged into electrical outlet
and into DC input connector on rear panel of receiver.
• Make sure AC electrical outlet works and supplies proper
voltage.
A
PEAK
PEAK
ON
B
LOW BATT
RF
POWER
TRANSMITTER
AUDIO
ANTENNA
POWER
POWER
No sound.
• Slide transmitter MUTE switch to ON.
A
PEAK
PEAK
ON
B
LOW BATT
RF
POWER
TRANSMITTER
AUDIO
• Extend antenna(s). AXR4N receiver antennas should point away
from each other at a 45° angle from vertical; AXR3 receiver
antenna should remain vertical. See Figure 8.
• Move receiver away from nearby metal objects.
• Remove obstructions and maintain line of sight between
transmitter and receiver.
ANTENNA
POWER
POWER
A
PEAK
PEAK
ON
B
LOW BATT
RF
POWER
• Move transmitter closer to receiver.
TRANSMITTER
ANTENNA AUDIO
POWER
POWER
• Increase transmitter gain until Transmitter Audio Peak light flashes
on loud peaks.
• Turn up receiver volume control as necessary.
A
PEAK
PEAK
ON
B
LOW BATT
RF
POWER
No sound or faint
sound.
TRANSMITTER
AUDIO
POWER
ANTENNA
POWER
• Turn up receiver volume control.
A
ON
B
PEAK
PEAK
• Check cable connection between receiver and amplifier or mixer.
LOW BATT
RF
POWER
Sound level from the
receiver is different
from that of a cabled
guitar or microphone.
• Adjust transmitter gain as necessary.
• Adjust receiver volume as necessary.
Sound level is different
when you change
guitars.
• Adjust transmitter gain to compensate for differences between
guitar output levels.
POWER
LOW BATT
POWER
Distortion increases
gradually.
• Replace transmitter battery.
ANTENNA
• If noise occurs when transmitter is turned off, remove or turn off
nearby sources of RF (such as other wireless systems, CB radios,
etc.).
• Use a wireless system that operates on a different frequency.
Bursts of noise,
distortion, or other radio
signals interrupt
performance.
A
B
LOW BATT
RF
Momentary loss of
sound as transmitter is
moved around
performing area
(dropouts).
ANTENNA
POWER
• Reposition receiver and perform walk-through test. If audio
dropouts persist, mark “dead” spots and avoid them during
performance.
A
B
LOW BATT
RF
6
English
SYSTEM AND COMPONENT SPECIFICATIONS
RF Carrier Frequency Range
169.445 to 240.000 MHz
AXR3 AND AXR4N RECEIVER SPECIFICATIONS
AXR4N
AXR3
Operating Range:100 m (328 ft.) under typical conditions
Audio Frequency Response: 50 to 15,000 Hz, $3 dB
Connector
3-Pin XLR (Male) and
1/4” Phone Plug
1/4” Phone Jack
Image Rejection: 75 dB typical
Spurious Rejection: 75 dB typical
System Distortion (ref. ꢀ15 kHz deviation, 1 kHz modula-
tion): 0.1% THD typical
Maximum Output
Levels at 15 KHz
deviation
1/4”: + 5dBV
XLR: –10 dBV
–6.8 dBV
Signal/Noise Ratio: 102 dB
Sensitivity: –110 dBm for 12 dB SINAD typical
Nominal Output
Levels
1/4”: –8 dBV
XLR: –30 dBV
–32 dBV
Operating Temperature Range
Output Configuration
Actual Impedance
Active Balanced
3.3 KΩ
Unbalanced
1 KΩ
–18° to 57° C (0° to 135° F) NOTE: Battery characteristics
may limit this range.
Battery Life: 18 hours with 9 V alkaline battery (Duracell
MN1604 recommended).
Connector Pin
Assignments
XLR: Pin 1: ground;
Tip: hot; Sleeve:
Pin 2: hot; Pin 3: cold ground
1/4”: Tip: hot; Sleeve:
ground.
AXB1, AXB1G BODYPACK
TRANSMITTER SPECIFICATIONS
Dimensions (AXR4N) 41 mm H x 197 mm W x 138 mm D
(1.625” H x 7.77” W x 5.42” D)
RF Output
50 mW Typical
Dimensions (AXR3)
35mm H x 152 mm W x 98 mm D
(1.38”H x 5.98” W x 3.85” D)
Input
Configuration
Unbalanced
Net Weight (AXR4N)
Net Weight (AXR3)
Power Requirements
Power Supply
435 g (15.4 oz.)
Connector Type
1/4 Inch (AXB1G); 4-pin Tini Q-G (AXB1)
Actual Impedance 1 MΩ
Maximum
Recommended
Input Level*
192 g (6.8 oz.)
12–18 VDC nominal, 200mA
+12 dBV
120 V or 230V AC adaptor with 2.1 mm female
plug
Minimum
–80 dBV
Recommended
Input Level**
Voltage/Current/Phant Yes
om Power Protection
Yes
Pin 1:Tied to Ground
Connector Pin
Assignments
(AXB1)
Pin 2:Tied to +5 V
Certification
Pin 3:Tied to Audio
AXB1G, AXB1:Accepted under FCC Parts 74 and 90. Certi-
fied by IC in Canada under TRC-78.
Pin 4:Tied to 20kΩ Resistor and Audio Ground
Connector Pin
Assignments
(AXB1G)
AXH2/31, AXH2/58: Type Accepted under FCC Parts 74 and 90.
Certified by IC in Canada under TRC-78. Conforms to
European Union directives, eligible to bear CE marking;
meets European Union Requirements. Type Approval: pr
I–ETS 300 422, BZT 17 TR 2019, and BAPT 122 R 1. EMC
Immunity: pr ETS 300 445.
Sleeve: Tied to Ground
Tip: Tied to Audio
Dimensions
64 mm H x 106 mm W x 24 mm D
(2.52” H x 4.17” W x 0.95” D)
96.4g (3.4 oz.)
Net Weight
Power
Requirements
Nominal Current
Drain
9 V alkaline battery (Duracell MN1604
recommended); 8.4 V NiCd battery optional.
AXR3, AXR4N: Approved under the Declaration of Conformity
provision of FCC Part 15 (AXR3). Certified by IC in Canada
under RSS 123 (AXR4N). Conforms to European Union di-
rectives, eligible to bear CE marking; mets European Union
Requirements. EMC Immunity: pr ETS 300 445. Power sup-
ply meets Low Voltage Directive: 73/23/EEC.
30 mA
* Gain Control at minimum
** Gain Control at maximum
AXH2 HAND-HELD TRANSMITTER SPECIFICA-
TIONS
AXH2/58 (SM58)
AXH2/31(BG3.1)
RF Output
50 mW Typical (FCC); 20 mW Typical (ETSI)
Dimensions
236 mm H x 51 mm D 222 mm H x 51 mm D
(9.29” H x 2.01” D)
295g (10.4 oz.)
(8.74” H x 2.01” D)
266g (9.4 oz.)
Net Weight
Power Requirement
9 V alkaline battery (Duracell MN1604 recom-
mended); 8.4 V NiCd battery optional.
Nominal Current
Drain
30 mA
30 mA
7
English
ACCESSORIES, LICENSING AND WARRANTY
FURNISHED ACCESSORIES
DECLARATION OF CONFORMITY
Screwdriver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65A1659
Sew–in Mounting Block
We of
Shure Incorporated
222 Hartrey Ave.
Evanston IL 60202–3696 U.S.A.
(WL93 AXSLWD Only) . . . . . . . . . . . . . . . . . . . 65B1733*
Receiver AC Adapter . . . . . . . . . . . . . . . . . . . . . PS20 (120V)
Guitar Cables (2) (AXSGW systems Only) . . . . . . . WA303
Swivel Adapter (AXS31/58 systems Only) . . . . . . . . WA371
Plastic Carrying Case (Diversity Systems) . . . . . . . WA605
Plastic Carrying Case (Single Antenna systems) . . WA600
847–866–2200
declare under our sole responsibility that the following prod-
ucts,
OPTIONAL ACCESSORIES
Model: AXR3
Model: AXR4N Name: AXR4N Diversity
Receiver
Name: AXR3 Receiver
Anti–Roll Device for Handheld Transmitters . . . . . . . . . A1K
Neoprene Bodypack Belt Pouch . . . . . . . . . . . . . . . . WA570
Line Matching Output Transformer (AXR3 Receiver) . A95U
1.8 Meter (6 ft.) Receiver-Mixer Cable . . . . . . . . . . . WA410
Rack-Mount Kit (AXR4N Diversity Systems Only) . . . . URT
Amp/Powered Mixer stand for Receivers . . . . . . . . . WA595
AXSLWD Systems Only
were tested and found to comply with Part 15 of the FCC rules.
Operation is subject to the following two conditions: (1) this de-
vice may not cause harmful interference, and (2) this device
must accept any interference received, including interference
that may cause undesired operation.
Tan version of WL93 . . . . . . . . . . . . . . . . . . . . . . . . . . WL93T
Single-Mount Tie Clip (2)
(WL93) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RK354SB
Dual-Mount Tie Clip
Testing was completed by the following NVLAP or A2LA ac-
credited laboratory:
(WL93) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RK307DB
Black Windscreen (4)
(WL93) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RK355WS
Tan Windscreen and Tie Clip (2 each)
(WL93) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RK304T
AXSHW Systems Only
BZT privat CETECOM GmbH
66117 Sarbruken
Unterturkheimer StrBe 6–10
Deutschland
telephone +49 681 598 – 9000
fax +49 681 598 – 9075
Foam Windscreens (2) and Clothing Clip (WH20)RK318WS
Croakies Headband (WH20) . . . . . . . . . . . . . . . . . . . RK319
Croakies Headband and Wire Frame (WH20) . . RPM600
Microphone and Boom Assembly (WH20)
1/4” plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RPM100
Shure Inc., Manufacturer.
∗ Furnished in multiples of 4.
∗∗ Includes 2 tie bars and 2 windscreens.
For additional microphone service or parts information, please
contact Shure’s Service department at 1–800–516–2525 or
please contact your Authorized Shure Service Center.
Signed:
Date: June 15, 1999
Name, Title: Craig Kozokar, Senior Quality Engineer
WARRANTY INFORMATION
ADDITIONAL INFORMATION FOR THIS SHURE
WIRELESS SYSTEM
This Shure wireless transmitter is accepted under FCC Part 74
and/or Part 90.
Shure Incorporated (“Shure”) hereby warrants that these prod-
ucts will be free from defects in material and workmanship for a
period of two years from the date of purchase for all microphone
cartridge and housing assembly parts and, for a period of one
year from the date of purchase, all transmitter and receiver
parts. At its option, Shure will repair or replace the defective
product and promptly return it to you. You should retain proof of
purchase to validate the purchase date and return it with any
warranty claim. If you believe this product is defective within the
warranty period, carefully repack the unit, insure it, and return it
postpaid to:
IMPORTANT: Licensing of Shure wireless microphone
equipment is the user’s responsibility, and licensability de-
pends on the user’s classification and application, and on
the selected frequency. Shure urges the user to consult the
appropriate telecommunications authority before choosing and
ordering frequencies.
Shure Incorporated
Attention: Service Department
222 Hartrey Avenue
Changes or modifications not expressly approved by Shure
Inc. could void your authority to operate this equipment.
Evanston, IL 60202-5730 U.S.A.
Customers outside the U.S.A. should ship the product to the au-
thorized Shure Distribution Center in their region.
8
|