MODEL
AL-841
DIGITAL LASER COPIER/
PRINTER/SCANNER
PRINTER/SCANNER
OPERATION MANUAL
Page
●
●
●
●
●
GETTING STARTED
PRINTING
2
12
18
20
24
SCANNING
TROUBLE?
APPENDIX
♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
WARNING:
FCC Regulations state that any unauthorized changes or modifications to this
equipment not expressly approved by the manufacturer could void the user’s
authority to operate this equipment.
Note:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
●
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
●
●
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
●
♠ ♠ ♠ ♠ ♠ ♠ ♠ ♠ ♠ ♠ ♠
♠ ♠ ♠ ♠ ♠ ♠ ♠ ♠ ♠ ♠ ♠ ♠ ♠ ♠ ♠ ♠ ♠ ♠ ♠ ♠ ♠ ♠ ♠ ♠ ♠
Shielded cables must be used with this equipment to maintain compliance
with FCC regulations.
CONTENTS
1 GETTING STARTED
INTRODUCTION
– Making floppy disks from CD-ROM
MAIN FEATURES
CONNECTING THE INTERFACE CABLE
INSTALLING THE PRINTER DRIVER SOFTWARE
– Description of the printer driver
– Checking the hardware and software requirements
– Installing the printer driver
– “SHARP AL-841” driver group 11
2
3
3
4
5
5
5
5
2 PRINTING
PRINTING A PAGE 12
– Executing printing 12
– Indicators on the operation panel 13
SETTING PRINT CONDITIONS FROM PRINTER DRIVER 14
PRINTING FROM AN MS-DOS APPLICATION 16
– Print setting from the MS-DOS prompt 16
– Setting on the front panel 17
– Software printer setting 17
SCANNING
3
4
5
SCANNING AN IMAGE 18
– Scanning from a TWAIN-compatible application 19
– Exiting from AL-841 TWAIN software 19
TROUBLE?
TROUBLESHOOTING 20
USING OTHER INSTALLED DRIVERS 22
UNINSTALLING DRIVERS 23
APPENDIX
PRINTER SPECIFICATIONS 24
SCANNER SPECIFICATIONS 25
PARALLEL INTERFACE 26
PRINT AREA 27
1
GETTING STARTED
1
This chapter provides basic information for using the SHARP AL-841 and its features.
1
INTRODUCTION
This manual describes only the printer and scanner features of the AL-841.To get full use of all
printer and scanner features, familiarize yourself with this manual.
For quick reference during machine use, keep this manual in a handy location.
For a description of other features, refer to their separate manuals.
Conventions used in this manual
In this manual, the following icons are used to provide the user with information pertinent to the
use of the machine.
Cautions the user that damage to the machine or one of its components may
result if the contents of the caution are not properly followed.
Notes provide information relevant to the machine regarding specifications,
functions, performance, operation and such, that may be useful to the user.
●
When you try to execute printing while copying is being performed, printing
will be executed after copying is finished.
●
When you try to make a copy while printing is being performed, printing will
be interrupted and you can make a copy.Printing will be resumed after copying
is finished.
Trademark acknowledgments
Windows, MS-DOS, Windows NT and Windows Printing System are trademarks of Microsoft
Corporation in the U.S.A. and other countries.
IBM, PC/AT and OS/2 are trademarks of International Business Machines Corporation.
HP, LaserJet and PCL are trademarks of Hewlett-Packard Company.
All other trademarks and copyrights are the property of their respective owners.
2
INTRODUCTION
Making floppy disks from CD-ROM
The driver data in the CD-ROM can be copied to floppy disks.
Windows 95/Windows 98/Windows NT 4.0:
Insert the installation CD-ROM into the CD-ROM drive.
1
Double-click My Computer, Al_841 (CD-ROM), and Makedisk.
1
2
Double-click Makedisk.exe.
3
Follow the on-screen instructions.
4
Windows 3.1x:
Insert the installation CD-ROM into the CD-ROM drive.
1
Double-click the File Manager in the Main window of Program Manager and select
CD-ROM and the Makedisk directory.
2
Double-click Makedisk.exe.
3
4
Follow the on-screen instructions.
MAIN FEATURES
Printing from Windows 3.1x, Windows 95, Windows 98, and Windows
NT 4.0 applications
●
High-speed and high-quality printing can be performed fromWindows 3.1x, Windows 95,
Windows 98, andWindows NT 4.0 applications through the SHARP GDI (Graphics Device
Interface) system.
●
Since print data is processed in the computer, waiting time during printing is short.
Scanning fromWindows 3.1x,Windows 95,Windows 98, andWindows
NT 4.0 applications
●
The SHARP TWAIN interface software enables the AL-841 to perform high-quality
monochrome scanning directly from a TWAIN-compatible application.
TWAIN is an application programme interface (API) standard which is used to
scan images from scanners. The SHARP TWAIN interface software supports
the TWAIN standard, version 1.6.
3
CONNECTING THE INTERFACE CABLE
To use the AL-841 as a laser printer or scanner, connect it to your computer using a parallel
interface cable.
Use the parallel interface cable included with the AL-841.
For specifications of the parallel interface, see page 26.
1
Check that the power switches of both the machine and the computer are in the OFF
position.
1
Plug the parallel interface cable into the printer interface connector.Fasten the two bail
clips at the side of the printer connector to hold the interface connector in place.
2
Plug the other end of the cable into the parallel interface connector on your computer.
(Refer to your computer manual for details.)
3
Parallel interface
connector
Cable
Interface connector
Bail clip
This machine sends and receives data bi-directionally and at high speed.Some
switch boxes and pass-through devices cannot support high-speed, bi-directional
transfer of data, and using them may cause printing errors.
4
INSTALLING THE PRINTER DRIVER SOFTWARE
Description of the printer driver
The printer driver is the software program which runs the printer.It converts the data in your file
into information that the printer can understand. It also controls communication between the
printer and computer as the data is printed.
1
Checking the hardware and software requirements
You will need the following hardware and software in order to install the printer driver.
Computer type
Windows type
IBM PC/AT or compatible computer equipped with ECP
mode-equivalent bi-directional parallel interface and CD-
ROM drive
Windows 3.1x, Windows 95, Windows 98, Windows NT
4.0
CPU
486DX 66MHz or better
Physical RAM
Windows 95, Windows 3.1x: 8MB (16MB or more is
recommended.)
Windows NT 4.0: 12MB (16MB or more is recommended.)
Windows 98: 16MB (32MB or more is recommended.)
Virtual storage (swap file)
Display
8MB or more
640 x 480 dots (VGA) or better
11MB or more
Hard disk free space
The printer driver included in this product cannot be used under Windows NT
3.5x, OS/2, pure MS-DOS and other operating systems which are not described
above.
Installing the printer driver
The software for your machine is provided on the CD-ROM which was packed with your machine.
Before installing the printer driver, be sure to check the following items.
●
Is the machine connected properly to the computer?
●
Does the machine have paper?
●
Is there another GDI printer driver or Windows Printing System printer driver already
installed? If installed, change the printer port setting. For instructions on changing the
printer port setting, see USING OTHER INSTALLED DRIVERS on page 22.
The TWAIN software is automatically installed at the same time you install the
printer driver. See page 18.
5
INSTALLING THE PRINTER DRIVER SOFTWARE
Windows 95/Windows NT 4.0:
Load paper into the paper tray of the machine. For instructions on loading paper, see
the section LOADING COPY PAPER in the copier operation manual.
1
Turn on the machine.
2
1
Turn on your computer and start Windows.
3
Before installing the printer driver, be sure to close all other applications which
may be open.
When usingWindows 95 on a personal computer with plug & play*, the“Update Device
Driver Wizard” window will appear. Insert the installation CD-ROM into the CD-ROM
4
drive.Click the Next button and follow the on-screen instructions.If the “Copying Files”
window appears during this operation, enter R:\ (if the CD-ROM is designated as
drive R), click the OK button and follow the on-screen instructions.
●
If you use Windows 95 and the “New Hardware Found” window will appear, select
Driver from Disk Provided by Hardware Manufacturer and then click the OK
button. Proceed to step 6.
If you use Windows 95 and the screen shown above or the “New Hardware Found”
●
window does not appear, proceed to step 5.
If you use Windows NT 4.0, proceed to step 5.
●
* Plug & Play
This feature is effective if both the computer and peripheral equipment are equipped
with an IEEE 1284 compliant parallel interface.
The screen displayed depends on the version of Windows you are using.
6
INSTALLING THE PRINTER DRIVER SOFTWARE
Insert the installation CD-ROM into the CD-ROM drive.
5
Click the Start button and select Run. When the screen shown below appears, type
R:\SETUP (if the CD-ROM is designated as drive R) and click the OK button. Follow
the on-screen instructions.
1
The “Install From Disk” window will appear. Insert the installation CD-ROM into the
CD-ROM drive. Type R:\ (if the CD-ROM is designated as drive R) and click the OK
button. Follow the on-screen instructions.
6
If you have any problem with the test print, see TROUBLESHOOTING on page
20 and check the symptoms and solutions. Print the test page again after
removing the problem.
7
INSTALLING THE PRINTER DRIVER SOFTWARE
Windows 98:
Load paper into the paper tray of the machine. For instructions on loading paper, see
the section LOADING COPY PAPER in the copier operation manual.
1
Turn on the machine.
2
1
Turn on your computer and start Windows.
3
Before installing the printer driver, be sure to close all other applications which
may be open.
When using Windows 98 on a personal computer with plug & play*, the “Add New
Hardware Wizard” window will appear. Click the Next button and follow the on-screen
4
instructions.
●
If the “Add New Hardware Wizard” window does not appear, proceed to step 8.
* Plug & Play: For plug & play information, see page 6.
Select Search for the best driver for your device and click the Next button.
5
Insert the installation CD-ROM into the CD-ROM drive. Select CD-ROM drive and
click the Next button.
6
8
INSTALLING THE PRINTER DRIVER SOFTWARE
Windows driver file search will find the device “SHARP AL-841”. Click the Next button
and follow the on-screen instructions.
7
8
Insert the installation CD-ROM into the CD-ROM drive. Click the Start button and
select Run.When the window shown below appears, type R:\SETUP (if the CD-ROM
is designated as drive R) and click the OK button. Follow the on-screen instructions.
1
If you have any problem with the test print, see TROUBLESHOOTING on page
20.
9
INSTALLING THE PRINTER DRIVER SOFTWARE
Windows 3.1x:
Load paper into the paper tray of the machine. For instructions on loading paper, see
the section LOADING COPY PAPER in the copier operation manual.
1
Turn on the machine and then start Windows on your computer.
2
1
Before installing the printer driver, be sure to close all other applications which
may be open.
Insert the installation CD-ROM into the CD-ROM drive.
3
Choose File from the Menu bar in Program Manager, and then choose the Run…
command.
4
Type R:\SETUP (if the CD-ROM is designated as drive R) in the command line box
and then click the OK button.
5
Follow the on-screen instructions.
6
10
INSTALLING THE PRINTER DRIVER SOFTWARE
“SHARP AL-841” driver group
When the drivers are installed, the SHARP AL-841 driver group will be created. This
group allows the following functions to be executed.
DOS Emulation HELP
1
DOS Emulation Setup
See page 17.
Readme
The latest information on the printer driver and the TWAIN driver is included in this
note. Read the Readme first.
Status Monitor HELP
Status Monitor
The printer state and information on current printing are displayed on the status monitor
window. When printing starts, the status monitor screen will appear on the computer
display.
Uninstall AL-841
The printer driver and the TWAIN driver can be uninstalled.
If the drivers are uninstalled, printing and scanning cannot be performed on the
machine.
●
Be sure to read “Readme” found in the driver group before starting to print or
scan from application programs.
●
If you uninstall the printer driver, the TWAIN driver is uninstalled at the same
time.
11
PRINTING
2
PRINTING A PAGE
The printing method is described below.Read the description with the operation manual for the
application to be used.
●
Before you can use this machine as a printer, you must install the supplied
2
SHARP printer driver. Once this software has been installed, you can control
the printing of your documents from the printer driver which appears on your
computer screen. See INSTALLING THE PRINTER DRIVER SOFTWARE
on page 5.
●
When using multiple printers, you must change the printer setting from the
control panel to change the printer to be used.This machine cannot be used
with other GDI printers and printers that use the Windows Printing System.
For details, see USING OTHER INSTALLED DRIVERS on page 22.
Executing printing
Ensure that paper of the desired size is loaded in the paper tray. (See the section on
LOADING COPY PAPER in the copier operation manual.)
1
To print onto special papers such as transparency film, labels, thick paper and
envelopes, specify “Manual Feed” as the paper source using the printer driver,
and feed it one sheet at a time.
Turn on the machine.The ready (
) indicator will light up.
2
3
Select the settings for printing such as the number of sets and paper type from the
application.See SETTING PRINT CONDITIONS FROM PRINTER DRIVER on page 14.
Before printing, ensure that the AL-841 has been selected as the printer.
Print the file from your software application.
4
●
If copying is being performed when printing is started, copying will continue.
After copying is complete, printing will be executed when the clear ( ) key is
pressed twice or approximately 60 seconds (auto clear time)* has elapsed.
* The auto clear time varies with a user program setting. See the copier
operation manual.
●
Preheat mode and auto power shut-off mode will be canceled when printing
is started.
12
PRINTING A PAGE
●
●
If the paper size specified from the software application is larger than the
paper size in the machine, the image may be printed onto two sheets of paper.
If the paper size specified from the software application is larger than the
paper size in the machine, part of the image that is not transferred to the
paper may remain on the surface of the drum. In this case, the other side of
the paper may become dirty. If this occurs, change to the correct size paper
and print two or three pages to clean the image.
Indicators on the operation panel
2
The ON LINE indicator and the ready (
) indicator indicate the state of the machine.
Ready indicator
On:
Off:
Indicates the machine is ready for printing or
scanning (online), or printing is being
performed.
Indicates copying is being performed, scanner
data is being read, or the machine is in the
auto power shut-off mode.
ON LINE Power save
indicator indicator
ON LINE indicator
On: Indicates the machine is ready for printing or
scanning (online), printing is being performed,
or scanner data is being read.
Blinking: Indicates a copy job has interrupted a print
job.
Ready indicator
Off:
Indicates copying is being performed.
Power save indicator
On: Indicates the machine is in a power save mode.
13
SETTING PRINT CONDITIONS FROM PRINTER
DRIVER
The setting method for items in the printer driver are described below.
Also refer to the printer driver help for more information.
Before setting the printer driver, check the following items.
●
The AL-841 printer driver has been installed in the computer to be used. If not, see
INSTALLINGTHE PRINTER DRIVER SOFTWARE on page 5.
●
The AL-841 has been selected as the default printer on the computer to be used.
2
Windows 95/Windows 98/Windows NT 4.0:
Click the Start button of the computer and then select Printers from Settings.
1
If you use Windows 95/Windows 98, right-click the SHARP AL-841 icon in the Printer
folder and select Properties in the menu.
2
If you use Windows NT 4.0, right-click the SHARP AL-841 icon in the Printer folder
and select Document Defaults in the menu.
For this description, it is assumed that the mouse is configured for right hand
operation.
14
SETTING PRINT CONDITIONS FROM PRINTER DRIVER
The properties of the SHARP AL-841 printer driver will be displayed.If you useWindows
95/Windows 98, click the Driver Setup tab to display the following screen.
3
* Screen on Windows 95
Driver Setup tabs
By selecting a different
tab other driver settings
can be changed.
Example: Resolution
changes can be made
by selecting the Image
Quality tab.
2
Apply button
The settings which
have been selected
by each tab will be
saved.
*This button is not
displayed on
Windows NT4.0.
OK button
All driver settings which have been
Defaults button
selected by each tab will be saved
and the properties will be
terminated.
The settings which have
been selected by each tab
will be returned to their
default state.
Cancel button
Default All button
The settings which have been selected by
each tab will be canceled and the properties
will be terminated.
However, the settings which have been
saved will not be canceled.
All settings which have been selected
by all tabs will be returned to their
default state.
Windows 3.1x:
Double-click the Print Manager icon in the Main window of Program Manager.
Select Options in the Print Manager and then select Printer Setup.
Select SHARP AL-841 in the Installed Printers: and click the Setup button.
The properties of the SHARP AL-841 will be displayed.
1
2
3
4
15
PRINTING FROM AN MS-DOS APPLICATION
You can execute printing from an MS-DOS application which has been executed from the MS-
DOS prompt in Windows.
This machine can only print from applications run from the MS-DOS prompt in
Windows. It cannot print when running in native MS-DOS mode.
Print setting from the MS-DOS prompt
2
Windows 95/Windows 98 has the item, “Spool MS-DOS print jobs” in the port settings. If this
setting is not selected, the machine will not operate properly. Use the following procedure to
check the setting.
Click the Start button.
1
Select Settings and then click Printers.
2
Right-click the AL-841 icon in the printer dialog box and click Properties.
3
For this description, it is assumed that the mouse is configured for right hand
operation.
Click the Details tab in the Properties dialog box.
4
Click the Port Settings button.
5
Check that “Spool MS-DOS print jobs” is checked in the port setting dialog box.
6
16
PRINTING FROM AN MS-DOS APPLICATION
Settings on the front panel
Paper size, tray selection, and other options are set from the front panel. Use the following
procedure to start the front panel.
Windows 95/Windows 98/Windows NT 4.0:
Click Start, Program, SHARP AL-841, and DOS Emulation Setup.
1
Windows 3.1x:
Double-click the DOS Emulation Setup icon in the SHARP AL-841 in Program
Manager.
2
1
Software printer setting
Set your MS-DOS application to use the following model printer.
HP LaserJet Series II (PCL4)
If this printer is not listed on the application’s printer setup, choose a PCL4 compatible printer.
17
SCANNING
3
SCANNING AN IMAGE
Before you can scan images using the AL-841 from aTWAIN-compatible application, you must
install the supplied SHARPTWAIN interface software.This software is automatically installed at
the same time you install the SHARP printer driver provided on CD-ROM. See INSTALLING
THE PRINTER DRIVER SOFTWARE on page 5.
●
Be sure to read “Readme” in the driver group before scanning images from
3
application programs.
●
When using the AL-841 as a scanner, you must make sure that your computer
Printer Port is configured for ECP mode. If the computer is set to a mode
other than ECP mode, change the mode to ECP mode.The method for setting
ECP mode differs depending on your computer. Refer to the documentation
for your computer.
●
Refer to the TWAIN help for more information.
●
For information about the state of operation panel indicators when using the
scanner function, see Indicators on the operation panel on page 13.
●
Preheat mode and auto power shut-off mode will be canceled when scanning
is started.
18
SCANNING AN IMAGE
Scanning from a TWAIN-compatible application
Menu names and their options are different for each application.
When multiple sources are available, choose a command to select a scanning device
from the application’s menu and select SHARP AL841TWAIN_xx.
1
2
Choose a command to acquire image from the application’s menu. AL-841 TWAIN
software starts.
3
Place the original and press the Preview button.
3
4
5
Set scanning parameters as necessary.
Press the Scan button.
You exit from AL-841 TWAIN software and the scanned image appears in the
application’s window.
Exiting from AL-841 TWAIN software
To terminate AL-841 TWAIN software, click on the close box while AL-841 TWAIN window is
active.
19
TROUBLE?
4
TROUBLESHOOTING
Some problems are common to the copier, printer and scanner features, so also check
TROUBLESHOOTING of the copier operation manual.
“Copier” in the column “See page:” indicates the description is in the copier
operation manual.
See
page:
Problem
Printer
driver
cannot be
installed.
Possible cause
Solution
5
Delete unnecessary files and
Hard disk free space is not
sufficient for installation of
the printer driver.
4
application software to increase hard
disk free space. (The driver requires
at least 11MB free space.)
5
The operating system is not Use Windows 3.1x, Windows 95,
proper.
Windows 98 or Windows NT 4.0.
Paper is not set correctly.
Insert the paper correctly.
Copier*1
Copier*1
Paper does
not feed into
the machine.
Too much paper in the paper Remove excessive paper from the
tray.
paper tray. For envelopes,
transparency film, and labels, feed
one sheet at a time.
The interface cable might
not be connected properly.
4
–
Check the interface connection.
The machine
does not
print.
The interface cable is
defective.
Check the cable with a computer and
printer which you know work. If
printing is still not possible, the
interface cable is defective.
The port setting is incorrect.
Check the printer settings in the
Windows Control panel to make sure
that the print job is being sent to the
correct port (for example, LPT1).
–
Copier*2
Copier*3
The TD cartridge or drum
cartridge is not installed
properly.
Ensure that the TD cartridge and
drum cartridge are installed properly.
The machine may be
configured incorrectly.
–
5
Check the application to make sure
that all the print settings are correct.
The printer driver may be
incorrectly installed.
Reinstall the printer driver software
and try printing a test page.
20
TROUBLESHOOTING
See
page:
Problem
Possible cause
Solution
The machine
prints wrong
data or
incorrect
characters.
Check the interface cable
connection.
The interface cable might
not be connected properly.
4
4, 26
The interface cable is not
IEEE-1284 compliant or a
switch box / pass-through
Use the interface cable included with
the AL-841. Remove any switch box /
pass-through device connected
device does not respond to between the computer and the AL-
high speed data transfer.
841. See the parallel interface
specifications.
–
If using Windows 3.1x, Print Double-click the Printers icon in
Printing is
too slow.
Manager may be disabled.
Control Panel and check the Use
Print Manager box.
There may be too many
applications open.
Close all unnecessary applications
before printing.
–
14
5
The resolution is set to
600dpi.
Set the resolution to 300dpi.
4
The computer may have
insufficient random-access
memory (RAM).
Install more random-access memory
(RAM) in your computer.
–
The page layout is too
complex.
Simplify the page layout.
Set resolution to 300dpi.
The machine
does not
print the full
image.
Resolution is set to 600dpi.
14
14
Page orientation setting may
be incorrect.
Change the page orientation with the
printer driver.
There may be too many
applications open.
Close all unnecessary applications
before printing.
–
–
The paper in the machine
may be larger than the
Load the correct paper into the
machine.
paper size specified in your
application or printer driver.
The interface cable is not
IEEE-1284 compliant or a
switch box / pass-through
device does not respond to
high speed data transfer.
Use the interface cable included with
the AL-841. Remove any switch box /
pass-through device connected
between the computer and the AL-
841. See the parallel interface
specifications.
4, 26
The CPU specifications may
be incorrect.
Check that the CPU of your
computer is 486DX 66MHz or better.
5
5
The computer may have
insufficient random-access
memory (RAM).
Install more random-access memory
(RAM) in your computer.
4
The interface cable might
not be connected properly.
Check the interface connection.
The machine
does not
scan.
*1 See the section on LOADING COPY PAPER.
*2 See the section on TD CARTRIDGE REPLACEMENT.
*3 See the section on DRUM CARTRIDGE REPLACEMENT.
21
USING OTHER INSTALLED DRIVERS
If you use another GDI printer orWindows Printing Systems printer, interference between printers
may occur and printing may not be performed properly.
To use another GDI printer or a Windows Printing System printer, you must change the port
setting of the printer driver using the following procedure.
If another printer does not operate properly when the AL-841 printer driver is
set to “FILE”, uninstall the AL-841 printer driver.
To uninstall the driver, see UNINSTALLING DRIVERS on page 23.
If after uninstalling the AL-841 printer driver, the printer still does not operate
properly, reinstall the printer driver you are using.
Windows 95/Windows 98/Windows NT 4.0:
Click the Start button.
4
1
Select Settings and then click Printers.
2
Right-click the AL-841 icon in the printer dialog box and then click Properties.
3
For this description, it is assumed that the mouse is configured for right hand
operation.
Click the Details tab (Ports tab – on Windows NT4.0) in the Properties dialog box,
select FILE: in the Print to the following port list box, and click the OK button.
4
Right-click the icon of the printer to be used and click Properties.
5
Click the Details tab (Ports tab – on Windows NT4.0) in the Properties window, select
LPT1 (or the currently used port), and click the OK button.
6
To use the AL-841 again, perform the same procedure but select the port to be
used (for example, LPT1) in step 4.
22
USING OTHER INSTALLED DRIVERS
Windows 3.1x:
Double-click the Control Panel icon in the Main window of Program Manager.
Double-click the Printers icon.The Printers window will then open.
Select AL-841, and then click the Connect button.
1
2
3
Select File from the list of options in the Ports window, and then click the OK button.
4
Select the new printer you would like to use from the list in the Installed Printers
window, and then click the Connect button.
5
6
7
Select the printer port to use for the new printer, and then click the OK button.
4
Click the Set As Default Printer button, and then click the Close button.
To use the AL-841 again, perform the same procedure but select the port to be
used (for example, LPT1) in step 4.
UNINSTALLING DRIVERS
If the printer driver and TWAIN driver are not installed correctly or if you no longer use this
machine, uninstall the printer driver and TWAIN driver from your computer using the following
procedure.
If using Windows 95/Windows 98/Windows NT 4.0, click Start, Program, SHARP
AL-841, and Uninstall AL-841.
1
If using Windows 3.1x, double-click the SHARP AL-841 icon in Program Manager and
double-click the Uninstall AL-841 icon.
When the “Confirm File Deletion” window appears, click the Yes button.
2
When the “Remove Programs From Your Computer” window appears, click the OK
button.
3
The printer driver and the TWAIN driver are uninstalled at the same time.
23
APPENDIX
5
PRINTER SPECIFICATIONS
Resolution
600dpi or 300dpi can be selected
Page description language
Page orientation
First print time
Print speed
SHARP GDI
Portrait or landscape
Approx. 20 seconds*
Max. 8 pages per minute (letter or A4)
Bi-directional parallel interface (IEEE 1284 compliant)
6MB
Interface port
Memory
5
* First print time may differ depending on operating conditions, such as power-supply voltage
and room temperature.
Also the time may differ depending on data quantity to be printed and applications.
As a part of our policy of continuous improvement, SHARP reserves the right to
make design and specification changes for product improvement without prior
notice. The performance specification figures indicated are nominal values of
production units.There may be some deviations from these values in individual
units.
24
SCANNER SPECIFICATIONS
Scanning method
Light source
Sensor
Flatbed scanner with moving scanning head
Fluorescent lamps
CCD
Scanning range
Resolution
Max. 8.3inch (W) x 13.8inch (H)
300dpi, 400dpi (standard) or 600dpi (pseudo-resolution)
can be selected
Output data
Scanning speed
Interface
1bit
0.85ms/line (Data transfer time is not included.)
IEEE 1284 compliant parallel interface (ECP mode only)
5
As a part of our policy of continuous improvement, SHARP reserves the right to
make design and specification changes for product improvement without prior
notice. The performance specification figures indicated are nominal values of
production units.There may be some deviations from these values in individual
units.
25
PARALLEL INTERFACE
This machine uses a bi-directional parallel interface.Use the interface cable attached to the AL-
841.
●
For specifications of the parallel interface of your computer, see its operation
manual.
●
Use the parallel interface cable specified by SHARP for prevention of external
radio wave interference. For details, contact your SHARP dealer.
Connector
36-pin DDK 57LE-40360-730B (D29)
female connector or equivalent connector
1
18
36
Cable
19
Shielded type bi-directional parallel
interface
For best results, use a printer interface
cable which is IEEE 1284 compliant.
5
Pin configuration
The pin numbers and signal names are
listed in the following table.
Pin No.
Signal name
Pin No.
Signal name
GND (STB RET)
GND (DATA1 RET)
GND (DATA2 RET)
GND (DATA3 RET)
GND (DATA4 RET)
GND (DATA5 RET)
GND (DATA6 RET)
GND (DATA7 RET)
GND (DATA8 RET)
GND (ACKNLG RET)
GND (BUSY RET)
GND (PE RET)
INPRM
1
2
STB
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
DATA1
DATA2
DATA3
DATA4
DATA5
DATA6
DATA7
DATA8
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
ACKNLG
BUSY
PE (Paper End)
SLTC
AUTO LF
(NC)
FAULT
(NC)
GND (0 V)
FG
(NC)
+5V
+5V
SLTC IN
26
PRINT AREA
The print area of this machine is shown below.
Portrait
E
Landscape
E
B
A
D C
F
E
G
E
F
D
C
G
Paper size
Print area
B
A
5
600 dpi
Dots
D
Paper size
A
B
C
E
F
96
G
Letter
Legal
Invoice
A4
5100
5100
3300
4960
3496
4299
5100
5100
4904
4904
3104
4760
3296
4104
4904
4904
6600
8400
5100
7015
4960
6070
7800
7440
6400
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
8200
4900
6815
4760
5870
7600
7240
96
96
100
100
95
A5
B5
Folio
Foolscap
96
96
300 dpi
Dots
D
Paper size
A
B
C
E
F
G
Letter
Legal
Invoice
A4
2550
2550
1650
2480
1748
2149
2550
2550
2456
2456
1552
2384
1648
2056
2456
2456
3300
4200
2550
3507
2480
3035
3900
3720
3200
4100
2450
3407
2380
2935
3800
3620
50
50
50
50
50
50
50
50
44
44
48
46
50
43
44
44
50
50
50
50
50
50
50
50
A5
B5
Folio
Foolscap
27
SOFTWARE LICENSE
PLEASE READ THIS LICENSE CAREFULLY BEFORE USING THE SOFTWARE. BY USING THE
SOFTWARE, YOU ARE AGREEING TO BE BOUND BY THE TERMS OF THIS LICENSE.
1. License. The application, demonstration, system and other software accompanying this
License, whether on disk, in read only memory, or on any other media (the “Software”) and related
documentation are licensed to you by SHARP. You own the disk on which the Software is recorded
but SHARP and/or SHARP’S Licensors retain title to the Software and related documentation. This
License allows you to use the Software on one or more computers connected to a single printer and
make one copy of the Software in machine-readable form for backup purposes only. You must
reproduce on such copy the SHARP copyright notice, the copyright notice of SHARP’S Licensors
and any other proprietary legends of SHARP and/or its Licensors that were on the original copy of
the Software. You may also transfer all your license rights in the software, the backup copy of the
Software, the related documentation and a copy of this License to another party, provided the other
party reads and agrees to the terms and conditions of this License.
2. Restrictions. The Software contains copyrighted material, trade secrets and other proprietary
material which is owned by SHARP and/or its Licensors and in order to protect them you may not
decompile, reverse engineer, disassemble or otherwise reduce the Software to a human-
perceivable form. You may not modify, network, rent, lease, loan, distribute or create derivative
works based upon the Software in whole or in part. You may not electronically transmit the Software
from one computer to another or over a network.
3. Termination. This license is effective until terminated. You may terminate this License at any
time by destroying the Software and related documentation and all copies thereof. This License will
terminate immediately without notice from SHARP and/or SHARP’S Licensors if you fail to comply
with any provision of this License. Upon termination you must destroy the Software and related
documentation and all copies thereof.
4. Export Law Assurances. You agree and certify that neither the Software nor any other technical
data received from SHARP, nor the direct product thereof, will be exported outside the United States
except as authorized and as permitted by the laws and regulations of the United States. If the
Software has been rightfully obtained by you outside of the United States, you agree that you will not
re-export the Software nor any other technical data received from SHARP, nor the direct product
thereof, except as permitted by the laws and regulations of the United states and the laws and the
regulation of the jurisdiction in which you obtained the Software.
5. Government End Users. If you are acquiring the Software on behalf of any unit or agency of the
United States Government, the following provisions apply. The Government agrees:
(i) if the Software is supplied to the Department of Defense (DoD), the Software is classified as
“Commercial Computer Software” and the Government is acquiring only “restricted rights” in the
Software and its documentation as that term is defined in Clause 252.227-7013 (c)(1) of the DFARS;
and
(ii) if the Software is supplied to any unit or agency of the United States Government other than DoD,
the Government’s rights in the Software and its documentation will be as defined in Clause 52.227-
19 (c)(2) of the FAR or, in the case of NASA, in Clause 18-52.227-86 (d) of the NASA Supplement to
the FAR.
6. Limited Warranty on Media. SHARP warrants the disks on which the Software is recorded to be
free from defects in materials and workmanship under normal use for a period of ninety (90) days
from the date of purchase as evidenced by a copy of the receipt. The entire liability of SHARP and/
or its Licensors and your exclusive remedy will be replacement of the disk which fails to meet the
limited warranty provided by this Clause 6. A disk will be replaced when it is returned to SHARP or a
SHARP authorized representative with a copy of the receipt. SHARP will have no responsibility to
replace a disk damaged by accident, abuse or misapplication.
ANY IMPLIED WARRANTIES ON THE DISKS, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN
DURATION TO NINETY (90) DAYS FROM THE DATE OF DELIVERY. THIS WARRANTY GIVES
YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY
FROM JURISDICTION TO JURISDICTION.
7. Disclaimer of Warranty on Software. You expressly acknowledge and agree that use of the
Software is at your sole risk. The software and related documentation are provided “AS IS” and
without warranty of any kind and SHARP and SHARP’S Licensor(s) (for the purpose of provisions 7
and 8, SHARP and SHARP’S Licensor(s) shall be collectively referred to as “SHARP”)
EXPRESSLY DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. SHARP DOES NOT WARRANT THAT THE FUNCTIONS
CONTAINED IN THE SOFTWARE WILL MEET YOUR REQUIREMENTS, OR THAT THE
OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE, OR THAT
DEFECTS IN THE SOFTWARE WILL BE CORRECTED. FURTHERMORE, SHARP DOES NOT
WARRANT OR MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS
OF THE USE OF THE SOFTWARE OR RELATED DOCUMENTATION IN TERMS OF THEIR
CORRECTNESS, ACCURACY, RELIABILITY, OR OTHERWISE. NO ORAL OR WRITTEN
INFORMATION OR ADVICE GIVEN BY SHARP OR A SHARP AUTHORIZED
REPRESENTATIVE SHALL CREATE A WARRANTY OR IN ANY WAY INCREASE THE SCOPE
OF THIS WARRANTY. SHOULD THE SOFTWARE PROVE DEFECTIVE, YOU (AND NOT
SHARP OR A SHARP AUTHORIZED REPRESENTATIVE) ASSUME THE ENTIRE COST OF ALL
NECESSARY SERVICING, REPAIR OR CORRECTION, SOME JURISDICTIONS DO NOT
ALLOW THE EXCLUSION OF IMPLIED WARRANTIES, SO THE ABOVE EXCLUSION MAY NOT
APPLY TO YOU.
8. Limitation of Liability. UNDER NO CIRCUMSTANCES INCLUDING NEGLIGENCE, SHALL
SHARP BE LIABLE FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES THAT
RESULT FROM THE USE OR INABILITY TO USE THE SOFTWARE OR RELATED
DOCUMENTATION, EVEN IF SHARP OR A SHARP AUTHORIZED REPRESENTATIVE HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME JURISDICTIONS DO NOT
ALLOW THE LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY
TO YOU.
In no event shall SHARP’S total liability to you for all damages, losses, and causes of action (whether
in contract, tort (including negligence) or otherwise) exceed the amount paid by you for the Software.
9. Controlling Law and Severability. For a portion of the Software related with Apple Macintosh
and Microsoft Windows, this license shall be governed by and construed in accordance with the laws
of the state of California and Washington, respectively. If for any reason a court of competent
jurisdiction finds any provision of this License, or portion thereof, to be unenforceable, that provision
of the License shall be enforced to the maximum extent permissible so as to effect the intent of the
parties, and the remainder of this License shall continue in full force and effect.
10. Complete Agreement. This License constitutes the entire agreement between the parties with
respect to the use of the Software and related documentation, and supersedes all prior or
contemporaneous understandings or agreements, written or oral, regarding such subject matter.
No amendment to or modification of this License will be binding unless in writing and signed by a duly
authorized representative of SHARP.
|