Model GI468
ONE (1) YEAR LIMITED WARRANTY
EURO-PRO Operating LLC warrants this product to be free from defects in material and
workmanship for a period of one (1) year from the date of the original purchase, when utilized for
normal household use, subject to the following conditions, exclusions and exceptions.
Professional Lightweight Iron
If your appliance fails to operate properly while in use under normal household conditions within the
warranty period, return the complete appliance and accessories, freight prepaid to
EURO-PRO Operating LLC, 94 Main Mill Street, Door 16, Plattsburgh, NY 12901
OWNER’S MANUAL
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC will
repair or replace it free of charge. Proof of purchase date and $ 9.95 to cover the cost of return
shipping and handling must be included. *
Model GI468
120V., 60 Hz., 1500 Watts
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement
of the unit at our option. This warranty does not cover normal wear of parts and does not apply to
any unit that has been tampered with or used for commercial purposes. This limited warranty does
not cover damage caused by misuse, abuse, negligent handling or damage due to faulty packaging
or mishandling in transit. This warranty does not cover damage or defects caused by or resulting
from damages from shipping or repairs, service or alterations to the product or any of its parts, which
have been performed by a repair person not authorized by EURO-PRO Operating LLC.
This warranty is extended to the original purchaser of the unit and excludes all other legal and/or
conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to the
specific obligations expressly assumed by it under the terms of the limited warranty. In no event is
EURO-PRO Operating LLC liable for incidental or consequential damages of any nature
whatsoever. Some states/provinces do not permit the exclusion or limitation of incidental or
consequential damages, so the above may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state or province to province.
*Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of
purchase date and to attach tag to item before packing with your name, complete address
and phone number with a note giving purchase information, model number and what you
believe is the problem with item. We recommend you insure the package (as damage in
shipping is not covered by your warranty). Mark the outside of your package “ATTENTION
CUSTOMER SERVICE”. We are constantly striving to improve our products, therefore the
specifications contained herein are subject to change without notice.
PRODUCT REGISTRATION CARD
FOR CANADIAN CONSUMERS ONLY
Please complete and return within ten (10) days of purchase. The registration will enable us to
contact you in the event a product defect is discovered. By returning this card you acknowledge
to have read and understood the instructions for use, and warnings set forth in the accompanying
instructions. Please return to:
Canada: EURO-PRO Operating LLC, 4400 Bois Franc, St. Laurent, Quebec, H4S 1A7
___G__I4_6__8_____________________________________________________________________
Appliance model
_____________________________________________________________________________
Date purchased
Name of store
For information or assistance:
EURO-PRO OPERATING LLC
94 Main Mill Street, Door 16
Plattsburgh, NY 12901
_____________________________________________________________________________
Owner’s name
_____________________________________________________________________________
Address
City
Prov./State
Postal/Zip Code
Tel.: 1 (800) 798-9378
Printed in China
11
IRONING CHART
GETTING TO KNOW YOUR ELECTRONIC IRON
The odor is safe and should not reoccur
after initial heating.
Before using your Shark Professional
Lightweight Iron, remove any labels,
stickers or tags that may be attached to
the body or soleplate of the iron.
When turned on for the first time, your
new iron may emit an odor for up to 10
minutes. This is due to the initial
heating of the materials used in making
the iron.
NOTE: Always refer to the garment care tag for ironing instructions. Before starting to
iron delicate fabrics, it is best to first test the temperature of the iron on a hem or an
inside seam.
Also, before ironing with steam for the
first time, allow iron to heat, hold in a
horizontal position and hit the burst of
steam button several times. The iron
may emit some small particles from the
steam holes. This is normal and will
clear after pressing the burst of steam
button several times.
DIRECTIONS
ON LABEL
SYNTHETIC
FIBERS, e.g.
acrylic, nylon
polyester
Display Panel
10
1
SILK
COTTON
LINEN
FABRIC
WOOL
3
4
13
14
LED
DISPLAY
PANEL
MIN
MAX
2
5
12
• • • • •
•
6
11
8
MINIMUM
STEAM
MAXIMUM
STEAM
STEAM
CONTROL
7
0
9
BURST OF
STEAM
8. Water Level Window
9. Stainless Steel Soleplate
10. Handle
11. Auto-Shut-Off
12. Power On Light
13. Fabric Settings
14. Temperature & Steam
Indicators
1. Electronic Temperature Control
2. Display Panel
3. Atomizer Spray Button
4. Burst of Steam Button
5. Variable Steam Control
6. Water Inlet Door
7. Spray Nozzle
SPRAY
15. Water Flask
Technical Specifications
Voltage:
Power:
120V, 60 Hz
1500 Watts
Illustrations may differ from actual product
9
2
FEATURES OF SHARK ELECTRONIC IRON
OPERATING INSTRUCTIONS
STORAGE
LED Display Panel
NOTE: The anti drip function reduces
water dripping and water stains. It does
not prevent water dripping and water
stains if you press the steam burst
button too often or if the temperature is
too low. The amount of water droplets
will eventually decrease after the iron is
used for 2 to 3 tankfuls of steaming and
ironing.
1. Always turn the variable steam
control to “0” after you have emptied
the water tank.
2. Allow the iron to cool down.
3. Always store the iron in the upright
position to protect the soleplate.
4. From time to time, clean the exterior
of the iron with a damp cloth and
wipe dry.
3
1
2
5. If you use spray starch, wipe the
soleplate occasionally with a soft
damp cloth to prevent the build-up of
deposits.
6. If the iron has not been used for a
few weeks, hold the iron horizontally
and allow to steam for 2 minutes
before ironing.
1. BURST OF STEAM BUTTON
Burst of steam provides extra,
sudden bursts of steam which aid in
removing stubborn wrinkles from
fabrics such as denim, cotton or
linen.
7. LED DISPLAY PANEL
Displays the fabric setting
(left) and the temperature
indicators (right).
2. ATOMIZER SPRAY
BUTTON
Pressing this button provides a
defined jet of spray which gently
moistens fabric.
3. VARIABLE STEAM
CONTROL
Minimum to maximum steaming
for different materials. Self
cleaning feature flushes internal
sole plate with water.
8. WATER FILLING INLET
The cover prevents dust and
foreign matter from entering
the water tank. It also stops
any water from spilling during
ironing.
4. ANTI-DRIP FUNCTION
Cuts off water when the
iron temperature is too
low.
9. PIVOT CORD
5. BUILT-IN ANTI-CALCIUM
FILTER
For left or right handed use.
Pivots up and down;
prevents dragging along the
fabric. The flexible cord
protector protects the cord
from fraying.
Prevents calcium build-up
and prolongs the life of the
iron.
6. STAINLESS STEEL
SOLEPLATE
Provides maximum glide-
ability and heat retention.
3
8
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
AUTO SHUT-OFF
SELF CLEANING
This appliance is for HOUSEHOLD USE
NOTE: Because of the soleplate design,
ordinary tap water may be used with this
iron. However, in very hard water areas,
we recommend using distilled or
demineralized water.
ONLY and may be plugged into any
120V AC polarized electrical outlet. Do
not use any other type of outlet.
The SHARK Professional Lightweight
Iron is equipped with an auto shut-off. The
auto shut-off switches the iron off if it has
been left standing unmoved in any
position (sideways, flat or upright) for
approximately 7-9 minutes. A red light on
the LED display panel will flash when the
iron switches itself off. (Fig. 6) To switch
the iron back on, just shake the iron side-
to-side several times.
It is important to “Self Clean” the iron at
least every two weeks to remove scale,
calcium, etc. The harder the water, the
more often the iron should be self
cleaned.
FABRIC & TEMPERATURE
INDICATORS
WARNING: Never fill the iron
with fabric conditioner, starches
or any other liquid, as these will
damage the steam mechanism. Do
not use contaminated water.
1. Open the water filling inlet cover.
Holding the iron at a slight angle,
pour water slowly into the water
filling inlet. See figure 1. Fill tank to
desired level or to the “MAX” water
level marking using the water filling
flask. (When the iron is upright, the
see-through water tank allows you to
gauge the amount of water.) DO
NOT overfill the tank. When finished
filling the iron with water, close the
water inlet cover before continuing.
1. Set the variable steam control to any
steam position.
2. Fill the water tank up to the “MAX”
level.
Press on the Electronic Temperature
Control to select the desired fabric
setting. The red lights at the left of the
LED Display Panel will light up.
At the same time, the temperature
indicator lights on the right side of the
LED Display Panel will start to flash.
They will stop flashing when the iron
reaches the selected temperature.
3. Stand the iron on its heel. Plug the
iron into the electrical outlet.
4. Press the electronic temperature
control button until you get the
“MAX” temperature setting on the
display panel and wait until the iron
heats up and temperature setting
light stops flashing.
5. Turn the variable steam control all the
way to the right to the self-cleaning
position and hold the iron horizontally
over the sink. (Fig. 7)
6. Boiling water and steam will now be
ejected from the holes in the
soleplate. The impurities and scale
are washed away with it.
7. Move the iron back and forth as this
happens.
8. If there is any water left in the water
tank after the iron stops steaming,
just empty the remaining water in a
sink following the instructions for
emptying the iron.
9. Turn the variable steam control to
the “0” position when the water tank
is empty.
DRY IRONING
For dry ironing, turn the variable steam
control dial all the way to the right to “0”.
This will cut off the steam flow if water is
in the water tank. All marked fabric
settings on the LED Display Panel can
be used for dry ironing.
1. Plug the cord into a polarized, 120V
AC electrical outlet. The power “ON”
light will come on, indicating that the
iron is receiving power.
2. Press on the electronic temperature
control button to select the desired
fabric/temperature setting. Turn the
variable steam control to “0”.
(See “Ironing Guide” for a guide to
temperature selection.)
3. Place iron on its heel (on a stable,
protected surface) while iron is
warming to desired temperature.
Flash
Fig. 6
EMPTYING THE IRON
1. Always empty iron after each use.
2. When finished using the iron, turn
the variable steam control to “0” and
press the electronic temperature
control button until the power light is
lit.
3. Unplug the iron from the electrical
outlet.
4. Turn the iron upside down over the
sink with the tip pointing downward
and allow the water to flow from the
opening.
Fig. 1
2. Plug the cord into a polarized, 120V
AC electrical outlet.
3. Press on the electronic temperature
control button to select the desired
fabric and temperature setting. Turn
the variable steam control dial to
the desired steam setting. (See
“Ironing Guide” for a guide to
temperature selection.)
STEAM IRONING
10.Place the iron back upright on its
heel to cool down before storing.
CAUTION DO NOT aim iron at
face, towards yourself, or
anyone else while using or adjusting
steam. Burns or serious injury may
occur.
WARNING Before filling the iron
with water, be sure the iron is not
plugged into the electrical outlet. The
iron may be filled with water while it
is hot.
5. Place iron upright and allow to cool
before storing.
CAUTION Use caution when
emptying the iron. Burns may
occur from touching hot metal
surfaces, hot water or steam.
Fig. 7
CAUTION TO PREVENT THE
RISK OF BURNS, use caution
when filling iron with water. Burns
can occur from touching hot metal
parts, hot water, or steam.
7
4
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
SELECTING IRON TEMPERATURES
IRONING HINTS
4. Place the iron on its heel on a stable,
protected surface and allow the iron
to heat for approximately two (2)
minutes or until the temperature
settings on the right side of the LED
display panel have stopped flashing.
5. Turn the variable steam control dial
to the right to increase the amount of
steam. When using extra steam, the
iron uses more water and it may be
necessary to fill the water tank more
often. (Fig. 2)
Always read garment labels and follow
the manufacturer’s ironing instructions.
Refer to the “Ironing Chart” on page 9
for temperature recommendations:
WARNING To prevent fire, do not
leave iron unattended while
connected.
•
Sort articles to be ironed according
to the type of fabric. This will reduce
the need to adjust the temperature
for different types of garments.
If you are not sure of the fiber
content of a garment, test fabric by
ironing a small area such as a seam
or inside hem section before ironing
a visible area. Start with a low
temperature setting and gradually
increase to find the best setting.
When reducing the temperature to
iron sensitive fabrics, allow
approximately 2 minutes for the iron
to cool to the new temperature
setting.
Fabrics such as velour, wool, linen
and silk are best ironed with an
ironing cloth to prevent shine marks.
•
Use low settings for nylon and other
synthetics.
•• Use moderate settings for wool,
silks, and blends.
Fig. 3
•
••• Use high settings for cottons and
linens.
5. Slide the variable steam control
up to increase the amount of
steam. (Fig. 3) When using extra
steam, the iron uses more water
and it may be necessary to fill
the tank more often. See page 4
for refilling the iron with water.
6. Steam is produced as soon as
the iron is held in the horizontal
position. Steam will stop coming
out when the iron is put on its
heel in a vertical position or by
setting the variable steam control
to “0”.
1. Stand the iron upright on its heel.
2. Plug the cord into a polarized, 120V
AC electrical outlet.
3. Press the electronic temperature
control until you get the desired
fabric/temperature setting.
4. The light on the right side of the LED
display panel will stop flashing when
the desired temperature has been
reached. (Fig. 5)
•
•
Fig. 2
BURST OF STEAM BUTTON
CAUTION DO NOT aim iron at
face, towards yourself, or
anyone else while using or adjusting
steam. Burns or serious injury may
occur.
ATOMIZER SPRAY NOZZLE
The atomizer spray nozzle is useful on
fabrics with stubborn wrinkles. Press the
spray button and a jet of water will spray
onto the fabric being ironed. (Fig. 4) The
water spray can be used with dry or
steam ironing as desired.
The burst of steam position is useful
when ironing denim, cotton and linens. It
provides quick bursts of steam which
aid in removing stubborn wrinkles.
Temp.
settings
The burst of steam feature can be used
with Dry or Steam ironing as desired.
1. Make sure the water tank is at least
1/2 filled with water.
2. Select the desired fabric and
temperature setting. Place the iron
on its heel (on a stable, protected
surface) and allow it to heat for
approximately 2 minutes.
3. Position variable steam control to the
burst of steam position. (Fig. 3)
4. With the iron in a horizontal position,
press the steam button several times
to prime the pump.
Fig. 5
Fig. 4
5
6
|