WWW.SHARKCLEAN.COM
Steam Pocket® Mop
S3505W
OWNER’S GUIDE
English
11. DO NOT unplug by pulling on
power cord. To unplug, grasp the
plug not the power cord. Do not
use extension cords or outlets
with inadequate current carrying
capacity.
22. Extreme caution should be
exercised when using this
appliance to clean stairs.
23. Never use steam mop without
micro-fiber pocket attached.
24. Keep your work area well lit.
12. DO NOT put any objects into
openings. Do not use with any
opening blocked.
25. Store steam mop indoors in a cool,
dry place.
13. DO NOT put hands or feet under
26. To avoid circuit overload, do not
operate another appliance on the
same socket (circuit) as the steam
cleaner.
the steam mop. Unit gets very hot.
14. Use ONLY on flat, horizontal
surfaces. Do not use on walls,
counters or windows.
27. If an extension cord is absolutely
necessary, an extension cord rated
a minimum of 15 ampere, 14 gage
cord should be used. Cords rated
for less amperage may overheat.
Care should be taken to arrange
cord so that it cannot be pulled or
tripped over.
15. DO NOT use on leather, wax
polished furniture or floors,
synthetic fabrics, velvet or other
delicate, steam sensitive materials.
16. DO NOT add cleaning solutions,
scented perfumes, oils or any other
chemicals to the water used in this
appliance as this may damage the
unit or make it unsafe for use. If
you live in a hard water area, we
recommend using distilled water in
your steam mop.
28. DO NOT leave your Steam Pocket®
Mop unattended when the system
is connected to a power supply
or electrical outlet.
29. DO NOT store unit with damp or
wet micro-fiber cleaning pocket
attached. Never leave the steam
mop in one spot on any surface for
any period of time with a damp or
wet micro-fiber cleaning pocket
attached as this will damage
your floors.
17. When in use, NEVER turn the
appliance over or on its side.
NEVER DIRECT STEAM TOWARDS
PEOPLE, ANIMALS OR PLANTS.
18. NEVER LEAVE THE STEAM
POCKET® MOP IN ONE SPOT ON
ANY SURFACE FOR ANY PERIOD
OF TIME WHEN MICRO-FIBER
POCKET IS ATTACHED.
30 Always unplug and allow the steam
mop to cool before removing or
changing mop heads.
19. Carefully remove the micro-fiber
pocket immediately after you have
unplugged and allowed the steam
mop to cool.
WARNING: Your steam mop
is designed to clean hard floor
surfaces that will withstand high
heat. Do not use on unsealed wood
or unglazed ceramic floors. On
surfaces that have been treated
with wax or some no wax floors,
the sheen may be removed by the
heat and steam action. It is always
recommended to test an isolated
area of the surface to be cleaned
before proceeding. We also
20. When cleaning the steam mop,
unplug the power cord from the
electrical outlet and clean with a
dry or damp cloth. Do not pour
water or use alcohol, benzene or
paint thinner on the unit.
21 To reduce the risk of fire, DO NOT
use a flammable or combustible
liquid to clean a floor.
recommend that you check the use
and care instructions from the floor
manufacturer.
Quick Start
When assembling your steam mop
there may be a little water in or around
the water tank. This is because we test
all our steam mops 100% before you
buy them, so you get a quality
Shark® Steam Pocket® Mop.
1
3
2
4
ASSEMBLE
1
Insert the mop handle into the
pump actuator (the tube that leads
to the tank). Push the mop handle
and pump actuator together until
you hear them click into place.
FILL
4
Lay the mop on the floor or on
a counter top and remove the
water tank cap by turning counter
clockwise. Fill the water tank using
the filling flask. Do not overfill the
water tank. Replace the water cap
and tighten.
2
Select a mop head. Choose the
All-Purpose, Versa-Tile™ or Large
Area mop head. Fit one side of
the pocket onto the head first,
then using the lavender loop, pull
the Steam Pocket® over the head.
Attach the quick fasteners on the
top of the pocket to secure in place.
IMPORTANT: Make sure your floors
are sealed. Before using the Steam
Pocket® Mop consult page 3 for
more information.
3
Snap the mop head into the base to
secure it. Press the release button
to exchange mop heads.
TOLL FREE: 1-800-798-7398
DIRT CAN’T HIDE ON
EITHER SIDE! When one
side of the pocket gets
dirty, just turn the mop
head over and clean with
the other side of the
Steam Pocket®.
5
QUICK TIP:
For easier
pushing
and pulling,
extend the
handle length.
6
QUICK TIPS: Your Steam
Pocket® Mop comes with 3
unique mop heads. Use the
All-Purpose mop head for
any room in your house, the
PREPARE
5
For your comfort, you can adjust
the height of the mop. Just lift the
latch on the tube 90 degrees to the
open position. Holding the handle,
extend the tube to the height that
is right for you and then close latch
to locked position.
™
triangular Versa-Tile mop
head for bathrooms and
tight spaces and the Large
Area mop head for wide
area cleaning.
NOTE: Do not leave your
Steam Pocket® Mop
6
Plug in mop and wait 30 seconds
or less for the mop to heat up.
Pump the handle of the mop by
pushing downward about 10 to 12
times to create steam.
unattended during use.
IMPORTANT: Never leave
the Steam Pocket® Mop in
one spot for any period of
time with a damp or wet
micro-fiber Steam Pocket®
attached as this will damage
your floors.
NOTE: Steam is created
automatically when you start
mopping.
TECHNICAL SPECIFICATIONS
Voltage:
Power:
Water
120V., 60Hz.
1550 Watts
Capacity: 450 ml (15 oz.)
TOLL FREE: 1-800-798-7398
English
Contents
Getting Started......................................................................2
Using Your Steam Mop .......................................................6
Using Your Carpet Glider ...................................................8
Care of Your Steam Mop....................................................9
Troubleshooting Guide .......................................................11
Notes..........................................................................................12
Thank you for
purchasing the
Shark® Steam
Pocket® Mop.
1
Getting Started
i
j
When assembling your steam mop there
may be a little water in or around the
water tank. This is because we test all
our steam mops 100% before you buy
them, so you get a quality Shark®
Steam Pocket® Mop.
k
a
l
b
d
n
o
c
m
e
f
p
h
g
a Two-Sided Micro-Fiber Steam Pocket®
i
j
Mop Handle
Quick Release Swivel Cord Wrap
for the Large Area Mop Head (1)
b Two-Sided Micro-Fiber Steam Pocket®
k Cord Clips
Telescopic Handle Latch
for the All-Purpose Mop Head (1)
l
c Two-Sided Duster Steam Pocket® for
m Water Tank Viewing Window
the All-Purpose Mop Head (1)
n Power-On Blue Light
(Lights up when plugged-in)
d Two-Sided Micro-Fiber Steam Pocket®
for the Versa-Tile™ Mop Head (1)
o Water Tank Cap
e Carpet Glider
p Large Area Mop Head
f
Filling Flask
g Versa-Tile™ Mop Head
h All-Purpose Mop Head
2
TOLL FREE: 1-800-798-7398
English
1
2
ASSEMBLE
IMPORTANT: Always make sure the
mop is UNPLUGGED from the wall
when not in use. Never fill the mop,
attach the mop head, change or
remove the micro-fiber pocket when
the mop is plugged into the wall. If
you have hard water you might want
to use distilled water to prolong the
life of the Shark® Steam Pocket®
Mop. Make sure you only add water
to the tank. Chemicals or cleaning
solutions may damage the appliance
and could be unsafe for you and your
family.
1
Insert the mop handle into the pump
actuator (the tube that leads to the
tank). Push the mop handle and
pump actuator together in until you
hear them click into place.
2
Select a mop head. All of the mop
heads can be used on your floors,
but the Versa-Tile bathroom head is
particularly useful for tight corners
and the Large Area mop head is
great for big jobs.
™
Use the lavender loop on the side of
the micro-fiber cleaning pocket to
place it around the mop head. Then
attach the quick fasteners on the
top of the pocket to secure in place.
You can also use the loop to pull the
dirty pocket off when you are done
mopping and it
has cooled.
3
Getting Started
4
3
3
Snap the mop head into the base to
secure it. Press the release button to
exchange mop heads.
IMPORTANT: Do not use on unsealed
wood or unglazed ceramic floors.
On surfaces that have been treated
with wax, the sheen may be removed
by the heat and steam action. It is
always recommended to test an
isolated area of the surface to be
cleaned before proceeding. We
recommend that you check the use
and care instructions from the floor
manufacturer.
4
Turn the water tank cap counter
clockwise and remove from the tank.
Use the filling flask and pour water
into the tank. Do not overfill. Replace
the cap on the water tank by turning
clockwise and tightening.
4
TOLL FREE: 1-800-798-7398
English
5
5
For your comfort, you can adjust
the height of the mop. Just lift the
latch on the tube 90 degrees to the
open position. Holding the handle,
extend the tube to the height that is
comfortable for you and then lower
the latch to locked position.
QUICK TIP: For easier pushing and
pulling, extend the handle length.
5
Using Your Steam Pocket® Mop
IMPORTANT: Do not use the mop
without first attaching a micro-fiber
pocket and adding water to the tank
first. When you are using the mop
for the first time, it might take longer
than the normal 30 seconds to start
steaming. Just pump the handle a
few times in a downward motion to
prime the pump and it should be
ready.
2
1
NOTE: Make sure the floors are
swept or vacuumed before using the
steam mop.
2
Pump the handle a few times in a
downward motion. This pumping
action will release steam as you
mop and allows you to customize
the amount of steam you want.
Begin mopping with a forward
and backward motion. The natural
motion of mopping will produce
steam.
1
Pull and twist the quick release cord
holder to unwrap the power cord
completely.
Plug into a 120-volt electrical outlet
The power “On” light will turn blue. It
takes approximately 30 seconds for
the mop to heat up and for the steam
to be ready.
6
TOLL FREE: 1-800-798-7398
English
3
3
When one side of the micro-fiber
Steam Pocket® gets dirty, just flip the
mop head and you can quickly start
using the other side. Dirt cannot hide
on either side.
4 When the water tank is empty, the
steam mop will stop producing
steam. You can refill the water tank
at any time as long as the mop is
unplugged from the outlet. Follow
the instructions from page 3.
IMPORTANT: Please wait 3-5 minutes
for the Steam Pocket® Mop to cool
off before switching the mop head or
the micro-fiber Steam Pocket®.
IMPORTANT: Never leave the
Steam Pocket® mop with a damp or
wet micro-fiber Steam Pocket® on
any floor surface for any amount of
time. This may damage the floor.
7
Using Your Carpet Glider
The Steam Pocket® Mop will
not clean your carpeting
or area rugs. However, it is
great for deodorizing and
freshening.
1
THE CARPET GLIDER
1 The Carpet Glider can be used with
the All-Purpose Mop Head to lightly
steam your carpet and area rugs.
Just place the mop head on top of
the glider and move back and forth
across a section of the carpet. The
Steam Pocket® mop will not clean
your carpeting or areas rugs, but it is
great for deodorizing and freshening.
NOTE: Please note that the Steam
Pocket® Mop rests on top of the
carpet glider and it is not a fixed
attachment. Do not leave steam mop
with carpet glider in one stationary
position for any period of time.
8
TOLL FREE: 1-800-798-7398
English
Care of Your Steam Pocket® Mop
AFTER USE AND STORAGE
1
When you have finished using the
Steam Pocket® Mop, unplug the cord
from the outlet and move it into an
upright position. Let the unit cool
3-5 minutes and release steam by
pumping the handle several times
before removing the micro-fiber
Steam Pocket® from the mop head.
3
1
2
2 Remove the micro-fiber Steam
Pocket® by releasing the quick
fasteners and using the lavender
loop on the side of the pocket,
avoiding contact with the hot pocket
or dirt. Then empty the water tank.
3
To store the Shark® Steam Pocket®
Mop, first remove the head (after it
has cooled and the steam has been
released) then hang on a large hook.
NOTE: If you want to store Steam
Pocket® Mop standing upright, make
sure it is leaning against a wall for
added support and safety. Always
store your Steam Pocket® Mop
with the micro-fiber Steam Pocket®
removed. Store away from children
and high traffic areas.
IMPORTANT: Steam Pocket® may be
very hot from the steam. Use caution
when removing. Let the unit cool
3-5 minutes.
9
Care of Your Steam Pocket® Mop
2
1
CLEANING YOUR MICRO-FIBER
STEAM POCKET®
2
If there are loose threads on the
Steam Pocket® , carefully cut the
thread with scissors. Do not pull on
them or cut at the base.
1
We recommend washing your micro-
fiber Steam Pocket® separately from
other fabrics to avoid picking up lint.
Only use liquid detergent (no powder
detergent). Do not use any fabric
softeners or bleach.
Line dry or dry on a low dryer
setting.
10
TOLL FREE: 1-800-798-7398
English
Troubleshooting Guide
PROBLEM
POSSIBLE REASONS & SOLUTIONS
Your Steam Pocket® Mop should be securely plugged
into a 120V AC electrical outlet only.
Steam Pocket® Mop
will not turn on.
Check your fuse or breaker.
Steam Pocket® Mop
will not make steam.
Prime the pump, see page 6 for more information.
Is there water in the water tank? If not, add water to
your Steam Pocket® Mop following the instructions.
Check to see if your micro-fiber Steam Pocket® is too
wet. We recommend you unplug the Steam Pocket®
Mop and change the micro-fiber Steam Pocket®.
Steam Pocket® Mop
leaves water on the
floor.
Make sure the Steam Pocket® is attached correctly.
Make sure the Steam Pocket® is attached correctly.
Steam Pocket® Mop
is hard to push.
Check to see if your Steam Pocket® is excessively dirty.
Try increasing the height of the pole for better leverage.
The micro-fiber Steam Pocket® might be dirty. Flip or
change the pocket.
If you washed the Steam Pocket® with powder, leftover
detergent may be causing the streaks. Re-wash pocket
with liquid detergent.
Floors are cloudy,
streaky or spotty
after steaming.
If you are cleaning in a kitchen area where there might
be a build-up of grease, clean the area first with a
degreasing agent such as an all-purpose cleaner or dish
soap and paper towels.
You might have left the mop in the same spot for
too long.
Do you have hard water? If you do, we recommend
using distilled water.
11
Notes
12
TOLL FREE: 1-800-798-7398
English
ONE (1) YEAR LIMITED WARRANTY
EURO-PRO Operating LLC warrants this product to be free from defects in material and
workmanship for a period of one (1) year from the date of the original purchase, when utilized for
normal household use, subject to the following conditions, exclusions and exceptions.
If your appliance fails to operate properly while in use under normal household conditions
within the warranty period, return the complete appliance and accessories, freight prepaid. For
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC
will repair or replace it free of charge. Proof of purchase date and $9.95 to cover the cost of
return shipping and handling must be included. *
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or
replacement of the unit at our option. This warranty does not cover normal wear of parts and
does not apply to any unit that has been tampered with or used for commercial purposes. This
limited warranty does not cover damage caused by misuse, abuse, negligent handling or damage
due to faulty packaging or mishandling in transit. This warranty does not cover damage or
defects caused by or resulting from damages from shipping or repairs, service or alterations to
the product or any of its parts, which have been performed by a repair person not authorized by
EURO-PRO Operating LLC.
This warranty is extended to the original purchaser of the unit and excludes all other legal and/
or conventional warranties. The responsibility of EURO-PRO Operating LLC warranty if any,
is limited to the specific obligations expressly assumed by it under the terms of the limited
warranty. In no event is EURO-PRO Operating LLC liable for incidental or consequential
damages of any nature whatsoever. Some states/provinces do not permit the exclusion or
limitation of incidental or consequential damages, so the above may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state or province to province.
*Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of
purchase date and to attach tag to item before packing with your name, complete address and
phone number with a note giving purchase information, model number and what you believe
is the problem with the item. We recommend you insure the package (as damage in shipping
is not covered by your warranty). Mark the outside of your package “ATTENTION CUSTOMER
SERVICE”. We are constantly striving to improve our products, therefore the specifications
contained herein are subject to change without notice.
OWNERSHIP REGISTRATION CARD FOR
CANADIAN CONSUMERS ONLY
Please complete and return within ten (10) days of purchase. The registration will enable
us to contact you in the event a product defect is discovered. By returning this card you
acknowledge to have read and understood the instructions for use, and warnings set
forth in the accompanying instructions.
RETURN TO: EURO-PRO Operating LLC, 4400 Bois Franc, St. Laurent, Quebec H4S 1A7
PURCHASER: ……………………………………………………………………………………………............
ADDRESS: ………………………………………………………………………………………………...............
S3505W
DATE OF PURCHASE: …………………….. MODEL: ………………...................................
NAME AND ADDRESS OF STORE: …………………………………………………………………..
13
U.S.:
EURO-PRO Operating LLC
180 Wells Ave
Newton, MA 02459
Canada: EURO-PRO Operating LLC
4400 Bois Franc
Ville St. Laurent, Québec H4S 1A7
1-800-798-7398
Sharkclean.com
COPYRIGHT© EURO-PRO OPERATING LLC 2010
PRINTED IN CHINA
REV. 100428
Illustrations may differ with actual product.
|